Question about Husqvarna Original Sears Craftsman Husqvarna Part 173288 LINK FRONT ASSY

Open Question

Impeller snowblower belt 8/25 - Husqvarna Original Sears Craftsman Husqvarna Part 173288 LINK FRONT ASSY

Posted by Anonymous on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

In heavy snow stop blowing snow


1 -Verify that all of your shear pins or bolts are in place. 1 on each auger and either 1 or 2 on the impeller fan.
2- Make sure all of the impeller blades are not bent as this will affect the throwing distance.
3 -Check the impeller bearing as it will lift if it is bad once snow is introduced into the machine.Remove the spark plug wire and verify that there is no tension on the impeller by turning it with a stick or broom handle. If it is safe reach through the chute hole and grab the impeller shaft and try to move it up and down, there should be little to no play.
4- Check your belt or belts. The belt should only deflect 1/2" with moderate pressure to be adjusted properly.
5- Check the condition of the belt, if the sides of the belt are glazed it may be slipping under load, if so replace the belt or try using a belt dressing spray.

in-heavy-snow-stop-blowing-snow-kf5g5icdgf4bb444zchblqxz-4-4.jpg
snowblower belt adjustment

Jan 31, 2016 | Garden

1 Answer

The impeller is turning but the blades are not. Belt seems ok


Depending on your make of snowblower, At the impeller there is usually 1 or 2 shear pins or bolts circled in red. If the impeller and the impeller shaft are turning but the augers are not, the gear may be stripped inside the gear box circled in yellow or the keyway may have sheared between the auger gear and the auger shaft.
26067241-ly2s5rnveefgf2wh5pb3yebn-3-0.jpg

Jan 24, 2016 | Garden

1 Answer

Snowblower....auger takes time to get going...like five minutes...it will struggle to start spinning then eventually warms up and is fine....whats the issue?


It is most likely your auger drive belts. There are two of them, and they need to be replaced periodically. Your manual should describe in detail as to how to replace the belts. Always start by removing the spark plug wire.
Improper gearcase lubricant could also cause problems. Your manual should tell you specifically what to use in the gearcase, and how to fill it. Also look for grease fittings on the auger and use a low-temp grease to service those fittings.
Lastly; behind the auger is the impeller shaft. Reach in and see if it wiggles. If it does, then have your impeller bearing replaced.

Feb 13, 2015 | Craftsman Snow Blower / Snowblower Bottom...

2 Answers

Auger on snowblower doesn't engage


how do I find good anime movie on Netflix help me fam

Feb 11, 2015 | Mtd Garden

2 Answers

MTD 8/26 snowblower


Either there is a belt or a chain off, or the linkage became disconnected or there is a pin sheared. Take one of the three. If you have power spinning like you said then those are your choices! Best of luck to you. Hope you beat the weather!

Feb 11, 2015 | Mtd Garden

1 Answer

Craftsman 179cc ohv 2 stage snowblower loses power in second stage throwing heavy snow


You should check for belt condition and adjustment. Under more load the auger/impeller belt might start to slip and would result in poor performance. For improved performance in wet slush there is an "impeller modification" that can be found with a web search. It's adding rubber wipers to the impeller blades and it does a great job of tossing that stuff out the chute instead of clogging it.

Feb 13, 2014 | Garden

1 Answer

Impeller does not rotate consistently and powerfully enough


check belt then check and adjust tension
it can be done on idler pulley or the cable going to handle for auger drive

Jan 01, 2014 | Craftsman 26" 208cc* Dual-Stage Snowblower

1 Answer

Ariens ST 724 impeller does not move under stress?


i have a old ariens ST724 snowblower engine will only run with full choke.

Jan 29, 2009 | Farmall Cub Tractor Radiator

Not finding what you are looking for?
Husqvarna Original Sears Craftsman Husqvarna Part 173288 LINK FRONT ASSY Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Husqvarna Experts

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

venugopal durairajan

Level 3 Expert

464 Answers

Are you a Husqvarna Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...