Question about kawasaki Motorcycles

1 Answer

Kavasaki brute force locked up while i was putting along, when you try to turn on it makes a loud noise in the area of the drive pulley

Posted by on


1 Answer

  • Level 1:

    An expert who has achieved level 1.


    An expert that got 5 achievements.


    An expert who has answered 20 or more questions within one hour.


    An expert who has answered 20 questions.

  • Contributor
  • 42 Answers

Sounds like your engine has seized up,. Almost certainly would be terminal, if the bike will move when in neutral but not when in gear I'm afraid its knackered. sorry

Posted on Jan 25, 2014


2 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 283 Answers

SOURCE: my brute force 750i 2005 keeps backfireing when i give it gass

It sounds like you may have water in the gas. Try draining the gas and replacing it with it fresh gasoline.

Posted on Oct 08, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My car keep on breaks alternator belts and it also makes this loud whistling noise. I've put on a new water pump, 3 alternators and several alternator belts

make sure that the pulleys of all the driven equipment are in alignment and not at a bit of an angle to the axis of the drive belt
To break belts something is not lined up properly or something is not turning freely

Dec 31, 2015 | 2000 Mazda Protege

1 Answer

Lg tromm wm1812cw dum makes load noise when spinning


THE DRIVE PULLEY- If the washer is making a loud noise the drive pulley might be worn out, cracked, loose or bent. Remove the drive pulley and inspect it carefully. If it is damaged or defective replace it.
THE DRIVE MOTOR- If the washer is making a loud noise the drive motor bearings may have worn out. Washer motors are normally almost silent when they run. If the motor is run without a belt hooked up to it and it's loud it will have to be replaced.

Jun 15, 2014 | LG TROMM WM2688H 4.0 cu.ft. Front Loading...

1 Answer

I have wh Holden statesman that recently just started playing up when I'm at a standstill at the lights I feel the car like it's going to die out then when I begin to drive it starts making clanking n

if its loud knocking noise at idle from front area of motor possibly crank pulley has separated from rubber.
when motor is not running can you grab the serpentine belt and move it along rotate it from left to right side of vehicle until it clunks to a stop which is the saftey lugs on the inside of the crank pulley, turning the pulleys?
if so the crank shaft balancer needs replacing
if you cant turn belt over by hand its ok and could be an internal motor issue, big end or camshaft bearing failure were the other common faults

Mar 29, 2014 | 1999 Holden VT

1 Answer

Can the drive pulley cause my 2006 kavasaki brute force to not crank??

Ask this question in motorcycles. A 2006 kawasaki brute force is not a printer

Dec 29, 2013 | Computers & Internet

1 Answer

Kawasaki brute force 750 cranks over then locks up it won't turn over by pulling the rope

sound to me you got faulty security switch check them 1st, specially the kick stand, most bike locks up if you try to place it in gears while the kick stand is still on. hope it helps

Dec 24, 2012 | Motorcycles

1 Answer

We just replaced the serpentine belt yesterday, after starting the car realized that the steering wasnt working, checked under the hood and the new serpentine belt is now broken, looks like it snapped

Maybe one of the drive pulleys has become seized. Sometimes the air conditioning compressor can be become seized and this puts a lot of strain on the serpentine belt. Did you take the tension of the tensioner pulley to slip the belt on or did you force it on. If you put it on with brute force the chances are that you did real damage to the belt. Check that all the pulleys turn (by hand). Check out how to take the tension off the tensioner pulley (often it is just a matter of putting a spanner on the pulley's central nut and rotating the mechanism anticlockwise against the spring tension. The belt should slip on without any effort if the tensioner is held back. Once on the tensioner can be released. The tension on the belt should be enough so that it is difficult to twist the belt, between pulleys, beyond about 90 degrees.

Jul 16, 2010 | 2002 Volvo S60

2 Answers

During the final spin, it is making a loud sound, is there a bearing that could be going?

The Maytag Neptune washer has 2 bearings seperated by a spacer pressed into the rear of the outer tub. The shaft from the inner basket support goes through a seal ten the 2 bearings where it attaches to the drive pulley. A small leak in the seal will cause the bearings to fail. The regular repair is expensive for both parts and labor as the outer tub has to be replaced. You can check around your area for a service company equipped to replace only the bearings rather than the tub.

Dec 30, 2009 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Loud buzzing noise

seems the the motor is ****! avoid switching it more further to prevent its motor from burning!
motor could be stuck due to rust build-up.
or something might have jammed along the motor area or along the rotating part.

Jun 18, 2009 | Dryers

1 Answer

Cant get new drive belt to fit washing machine. right one but cant get it to stretch enough to fit from drum wheel to motor

this is a common problem as nowadays stretchy belts are used in order to avoid motor adjustment.
fitting requires some brute force. the way i do it is to put the belt on the motor pulley then start it as much as i can on the drum pulley. turn the drum pulley keeping force sideways to push the belt on and as you turn, the belt will go on

Oct 21, 2008 | Hoover Washing Machines

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

71 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4727 Answers


Level 3 Expert

78257 Answers


Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides