Question about Motorcycles

1 Answer

Have crf450r with 13 to 1 piston on a go kart can the stop on the kick start be taken off so a left hand electric starter for go kart can be used to start in can't hold up race to get started I don't want running to long because of over heat

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Master
  • 1,727 Answers

No the internal kick start mechanism can only swing so far, any further and itll damage more than you are ready to fix...

Posted on Dec 28, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

HOW DO I replace blade


You must remove the spark plug and use a piston stop tool to prevent engine's crankshaft from spinning. An alternate piston stop method is use starter rope and fill the cylinder cavity to stop the piston. With piston block from movement you can remove that nut. Caution should be use as sometime these are left hand versions. Double check which you should be turning it.

Dec 06, 2014 | Echo Es210 Shredder

1 Answer

Yardworks snow blower


Leaks are normally from bad seals or ones put on engine wrong. Many snow blowers leak oil, very common. Electric start needs to be taken apart. Rust is problem most likely. When you engage the starter it kicks out the gear to turn over engine. Carefully remove the starter from engine, try to start starter an if the pinion gear does not kick out from starter disassembly it an try to clean rust away from action. Dont break wires around electric motor careful about getting dirt an rust in winding. Try to lube spring an moving parts around gear. One other thing it could be a sheared off gear on starter also.

Mar 22, 2014 | Tecumseh Garden

1 Answer

Problems starting the CRF450R 07 even after valves done,plus rewired stater. I've just gone from the usual cr250 2 stroke & all I ask seem to tell me the CRF needs getting used to,is this the case??


An 07 crf 450 doesnt have a starter motor. Are you sure about the year and model?
Starting a Thumper is not at all likd starting a two stroke. 2 strokes need a little flick on the kickstart and a little blip of the throttle. 4 stroke thumpers need a long, hard, deliberate kick and absolutely NO throttle. You may want to rest your right hand on the bar clamps to start it just to make sure your not adding fuel. Thumpers have a pretty big accelerator pump that can flood quickly and easily. Once you're used to it, it will become easier

Nov 03, 2013 | Motorcycles

1 Answer

I have a XR600 1990 model. I was washing it the other day and must have gotten water into the exhaust. It run but was really really rough. It then did something funny. As i was kicking it over it felt like...


Does your bike have the decompression lever? If so this could be what is jamming up causing your problems.
Otherwise what often happens is that the kick starter cogs don't mesh correctly, seeing as how you have taken the kick starter apart and put it back again and now no probs I would expect that to be your problem.
It might be worth checking your kick starter for wear, or the return spring to see if it isn't broken.

Oct 01, 2011 | 1990 Honda XR 600 R

1 Answer

How to remove chainsaw clutch


hi
remove statrer cover assy
remove plug, rotate engine until piston @ bdc - insert a thick 6 mm nylon starter rope through plug hole and rotate piston so that it pushes rope in between piston and cylinder top this locks the crankshaft

its called a soft stop

take a punch and hammer and give the clutch 1 or 2 hits in and clockwise direction clutch should loosen

to refit clutch , remove soft stop and rotate engine counter clockwise fit the stop and jamb it again between piston and cyl head then spin on the clutch ( threads are left hand ) use punch and give 1 or 2 hits to tighten again - remove soft stop and refit plug and starter cover assy
clutch should tighten further when engine runs

cheers paul


hope it helps

Aug 02, 2010 | Garden

1 Answer

I need to remove the fly wheel is it right or left hand thread? What is the best way to remove?


The fly wheel is right handed the clutch is left handed.
Please watch this it will help. It explains how to stop crankshaft rotation.

R² Drive Link Outboard Clutch
http://www.youtube.com/watch?v=cdqkIuVNUQc
  1. A length of starter cord or nylon rope may be used instead of the piston stop (retain 6" ± so you can remove it). Make sure the piston is near the top of the cylinder before feeding the cord or it can fall through the exhaust port and damage the piston as it rises.
Lou

Oct 03, 2009 | McCulloch Garden

1 Answer

How do I remove the sprocket and clutch on the Mac 3200 chain saw


Use this as a guide:
R² Drive Link Outboard Clutch
http://www.youtube.com/watch?v=cdqkIuVNUQc
  1. Check at the IPL for your saw to see if any special tools are needed.
  2. A length of starter cord or nylon rope may be used instead of the piston stop (retain 6" ± so you can remove it). Make sure the piston is near the top of the cylinder before feeding the cord or it can fall through the exhaust port and damage the piston as it rises.
  3. It is probably a left handed thread (tighten it to loosen it).
    Let us know how it worked for you. GL
    Lou

Sep 26, 2009 | McCulloch 16 In 4.5 Hp Electric Chainsaw...

1 Answer

How to remove clutch. McCulloch 438 chainsaw. This required to get access to chain lub system. Thank you, Michael.


I think its an outboard clutch, use this as a guide. A YouTube video shows the procedure using a Husqvarna 350 here:
http://www.youtube.com/watch?v=cdqkIuVNUQc
1. I cannot find an IPL for your saw, it may require special tools.
2. A length of starter cord or nylon rope may be used instead of the piston stop (retain 6" ± so you can remove it). Make sure the piston is near the top of the cylinder before feeding the cord or it can fall through the exhaust port and be cut when the piston rises.
3. It is probably a left handed thread (tighten it to loosen it).
Let us know how it worked for you. GL
Lou

Sep 10, 2009 | McCulloch 10" Electric Pole / Chain Saw

1 Answer

Mario Kart no start up


if you have upgraded your software on your wii, your freeloader won't work anymore. Mario carts is written in a way to stop people using programs such as freeloader. Its something called signed trucha, other people will not more. You could try buying a UK mario cart on ebay and trying that. Otherwise, looking into getting it mod chipped to overcome the region barriers. But always buy original games for it

Jan 19, 2009 | Nintendo Mario Kart (Wii) for Wii

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

77169 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...