Question about 2003 Suzuki GSX-R 600

1 Answer

Fyi light code c 29

I have a suzuki gsxr 600 2003 fyi light is on and it reads c 29 that means secondary throttle sensor i replaced the whole throttle body but the light is still on so im wondering if i take the butterfly values off the secondary what would happen?

Posted by on

  • Paul G
    Paul G May 11, 2010

    yes but did you change the sensor it self as well ?


    Thanks

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

You should have to adjust the throtle possition sensor.

Posted on Jun 03, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Code p1659


ok , you scanned or Autozoned it, if latter?, fail you do.
did they write it down wrong?
the code must be told accurately, (im sure you know that)

this code needs honda only meanings, P1
Electronic Throttle Control System Control Relay Off Malfunction
blown 7.5a fuse #15?
baring a simple fuse.
read the FSM./
the FSM covers this code, what to do and to find which part is
bad , not guessing, the ECU cant tell you what part is bad or dirty.
it only tells you what tests failed.
read the FSM or take the car to any ASE certified Mechanic.
this car is Throttle by wire. technology. (a pain , the TSB proves it.)

ever heard of a TSB? all good mech read them first
here is one example, on topic. too.
quote: (look up you car, and YOUR TSBs, read them all)
http://autoproimportrepair.com/Honda_TSB.htm


MIL Comes On With DTC P1659 TSB 05-008
SYMPTOM
In cold temperatures, the MIL comes on with DTC P1659 (electronic throttle control system control relay OFF malfunction). PROBABLE CAUSE Moisture inside the throttle control relay may freeze. This would cause the relay to fail, storing DIG P1659 along with any of these DTCs: P0135: Rear Air Fuel Ratio (A/F) Sensor (Bank 1, Sensor 1) Circuit Malfunction, P0141: Rear Secondary Heated Oxygen Sensor (Secondary HO2S, Bank 1, Sensor 2) Heater Circuit Malfunction, P0155: Front Air Fuel Ratio (A/F) Sensor (Bank 2, Sensor 1) Heater Circuit Malfunction, P0161: Front Secondary Heated Oxygen Sensor (Secondary H025, Bank 2, Sensor 2) Heater Circuit Malfunction, P0498: Evaporative Emission (EVAP) Canister Vent Shut Valve Control Circuit Low Voltage. CORRECTIVE ACTION Replace the electronic throttle control relay, the air/fuel sensor relay, and the starter cut relay.


Nov 20, 2013 | 2005 Honda Odyssey

1 Answer

I have a 2004 gxsr 1000 with fault code c42. It wont start. oil light is flashing and displays FI on the temp. Bike just crank but will not fire it up. Help?


Grab a paperclip.

Place the bike in Neutral, and take the rear seat cowling off. On the side of the bike between the tail section and the trunk you will find a connector that is covered by a rubber cap, and has two wires running into it. Remove the cap and take note of which one of the 4 sockets the two wires go to. Turn the bike ON and start it up, short the wires out with the paperclip. Where your speedo was flashing a -CHEC- with the temp should now be a CXX error code. Write this code down. Then shut the bike off. Match the code up with the list below. Grab a Manual and get to work!

(What you have just done is put the bike into "Dealer Mode".

GSXR Fuel Injection (FI) Code List:

C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR (1000 ONLY)

03-04 GSXR1000 Workshop Manual Verify Download

Sep 26, 2012 | 2004 Suzuki GSX-R 1000

1 Answer

I have a Suzuki GSX-R 750 and my F1 one light has started to come on when I excelerate some speed what does that mean.


Odds are its your SET valve needing adjustment, have the codes pull on the bike. If it is the SET, you can remove the SET system easily or you can have it adjusted.

If you get a code.

The codes are as follows:
C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIP OVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR
C00 - NO FAULT

Jun 28, 2011 | 2007 Suzuki GSX-R 750

1 Answer

What does -c29 in my gsxr 600 2007


means you're having a problem with your secondary throttle position sensor. very common problem with suzuki.

Jan 13, 2011 | 2007 Suzuki GSX-R 600

1 Answer

Hi i have a 2004 sv1000s not getting any fire from the spark plug line i put the bike in dealer mode an i got c41 what dos that mean ?


GSXR Fuel Injection (FI) Code List:

C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR (1000 ONLY)

heres a list of fault codes hope it helps

John

Jan 04, 2011 | 2003 Suzuki SV 1000 S

1 Answer

F1 code on my 2006 suzuki gsxr. it just started an 2 hrs ago drove it home in 20 degree weather now f1 code and no start


When the red light comes on, eg (F1) use these fault codes to find your problem. To extract the codes from the computer system, there is a two pinned connector hanging out of the wiring harness, on the left hand rear of the bike, (say above the pillion foot peg under rear trim. Be sure not to confuse the other connector used by the Suzuki Workshop Mechanics, as this has four or five wires to the connector) After locating the one with only two wires at the back, use a split pin or paper clip to bridge the two wires togeather and turn the ignition to the ON position. You should now be able to read the code on the console. The fault codes are as follows,,
**** GSXR Fuel Injection (FI) Code List:*****
C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR C29 - SECONDARY THROTTLE POSITION SENSOR C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL

Feb 03, 2010 | 2006 Suzuki GSX-R 600

1 Answer

Red light on odometer comes on.... And f1 light also


That is the Suzuki equivalent to a "Check engine light"

Turn your key on and verify the FI light is on and that your red kill switch is set to 'Run'

Remove your seat and behind the battery area you should find a white 6 pin connector (likely with a black rubber boot on it) Using a paperclip connect the white/red striped wire to the black/white striped wire.

Your display should Now read whatever codes are active.
If it reads C00- then there are no active codes. Note that when you turn the key off, the memory is erased so if you have an intermittent fault you should not turn the key off until you pull the codes.

Codes are as follows:

C11 - CAMSHAFT POSITION SENSOR
C12 - CRANKSHAFT POSITION SENSOR
C13 - INTAKE AIR PRESSURE SENSOR
C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C36 - SECONDARY INJECTOR SIGNAL #1
C37 - SECONDARY INJECTOR SIGNAL #2
C38 - SECONDARY INJECTOR SIGNAL #3
C39 - SECONDARY INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR
C49 - PAIR CONTROL SOLENOID VALVE
C60 COOLING FAN CONTROL SYSTEM



Sep 09, 2009 | 2007 Suzuki GSX-R 1000

2 Answers

Yes have 2006 gsxr 600 it flashs F1 will not crank


there is a plug under your seat with 2 wires that you need to short out. The fI code is a dealer code like a check engine light on your car. You need the actual problem code. turn the bike on and keep it running short out the two wires in a white harness under your seat and then the f1 will change to a C## code.
C14 - THROTTLE POSITION SENSOR
C15 - ENGINE COOLANT TEMPERATURE SENSOR
C21 - INTAKE AIR TEMPERATURE SENSOR
C22 - ATMOSPHERIC PRESSURE SENSOR
C23 - TIPOVER SENSOR
C24 - IGNITION SIGNAL #1
C25 - IGNITION SIGNAL #2
C26 - IGNITION SIGNAL #3
C27 - IGNITION SIGNAL #4
C28 - SECONDARY THROTTLE VALVE ACTUATOR
C29 - SECONDARY THROTTLE POSITION SENSOR
C30 - SECONDARY THROTTLE CONTROL UNIT
C31 - GEAR POSITION SENSOR
C32 - INJECTOR SIGNAL #1
C33 - INJECTOR SIGNAL #2
C34 - INJECTOR SIGNAL #3
C35 - INJECTOR SIGNAL #4
C41 - FUEL PUMP CONTROL SYSTEM
C42 - IGNITION SWITCH SIGNAL
C46 - EXHAUST CONTROL VALVE ACTUATOR (1000 ONLY)

Also a good place to look to make sure you have the correct wires is :
http://www.gixxer.com/forums/showthread.php?t=192222
it is a great site to belong to for future issues or just for fun

Sep 03, 2009 | 2008 Suzuki GSX-R 600

1 Answer

How do I check the STVA on my gsxr 600 K1 as code


It is indicating a mismatch with either the secondary butterfly, the actuator or the sensor. The easy fix is to buy a second-hand throttle body from a wrecker and install that. The long and expensive answer is to buy a new TB ($1000, near enough). Alternatively, 'fix' the secondary butterfly in the open position and live with it.

Jun 28, 2009 | 2001 Suzuki GSX-R 600

1 Answer

What is a fault code ct 28 on gsxr 600


c28 is the code for a problem with the secondary throttle valve actuator
hope this helps
regards bert31000

Mar 17, 2009 | 2001 Suzuki GSX-R 600

Not finding what you are looking for?
2003 Suzuki GSX-R 600 Logo

Related Topics:

295 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76649 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...