Question about Buell Motorcycles

1 Answer

Electric choke wireing

Balast voltage

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Buell Master
  • 41,865 Answers

Hi, Anonymous for more information about your issue and free downloads that you will need please visit the websites below, and for specific information or questions, please feel free to contact me at xlch@mail.com. Good luck and have a nice day. http://www.badweatherbikers.com/buell/messages/20164/59815.html?1448003540
buell Electric choke wiring ballast voltage Google Search
http://buellmods.com/content/downloads/manuals/xbxulysses/2006_ulysses_manual.pdf
TWIN Motorcycles Buell parts
Buell Motorcycle Owners Manuals

Posted on Jan 20, 2016

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My right side headlight not working on A4, 2007. Install new H7 bulb from Audi but it did not work. I install the right bulb into the drivers side and it work. I suspect an electrical problem. Possible no...


if it is a hid light system they are famous for the balast going bad. follow the wires from light bulb. if they go into a box then its a hid system and it is the balast box that needs to be replaced. also check the fuses, sometimes there are seperate fuses for each headlight.

Mar 09, 2013 | Cars & Trucks

1 Answer

I put a new battery in my 1986 Dodge ram 50 that has been sitting for a long time. I have no power, is there a master fuse somewhere I need to check?


Check ur balast resistor on the coil located next to the batery if this is bad it can cause either no electricity or too much electricity going through ur vehicle could blow fuses all the time or not give any power to them if u have a ohm meter. Disconnect wires going to balast and read across terminals if it reads more the 1.7 ohms the replace it u should not see k ohms or M ohms just 1.7 or lower. Hope this helps

May 24, 2012 | 1986 Dodge Ram 50

2 Answers

Got a new carborater with electric choke. how do i wire it?


The electric choke needs to be wired to a keyed power source.

Jul 11, 2011 | Chevrolet 1500 Cars & Trucks

1 Answer

84 ford f150 carburetor was rebuilt runs great when cold kicks and bucks when warm have to stomp on throttle to get to go


Sounds as if your choke is hanging up, or not opening at all. With the engine warm remove the air cleaner, there is a butterfly valve right inside the top of the carburetor If this is closed or mostly closed your choke needs to be adjusted. There are manual and electric chokes, yours should be an electric choke. First with engine cold and the key turned to on check for voltage at the choke wires. If you have voltage, then you might just need to adjust your choke. Electric chokes heat up an element inside the choke to tighten a spring and open the choke butterfly valve at the top of the carburetor. There should be between 4 and 5 screws that hold a ring around the choke housing on the side of the carburetor with the wires going to it. While holding the round choke housing in place loosen all of the screws on the retaining ring. If you can feel the choke housing wanting to spin turn it the opposite way that it wants to turn. Do this in stages until your choke butterfly valve is open with the key turned on, or the engine warm. Hope this helps if you have more questions just ask.

Jun 18, 2011 | Ford F-150 Cars & Trucks

1 Answer

Engine runs rough and istrument Gages not working


It sounds like you need to inspect the wiring harness and look for broken wires and any wires that are hanging they may not be connected, the black exhaust is caused by a choke plate that is not opening on the carb the electric choke is not getting any voltage through the wire or the choke plate is out of adjustment it should be wide open after 5 minutes of running, check the fuses to be sure there is no blown fuses and check the wire that goes to the carb. to ensure it has 12 volts.

Dec 02, 2009 | 1985 Ford F150

2 Answers

Ballast error status - lamp voltage too high


You need to replace the balast as the voltages are buringing the bulb out and this is caused by a balast that is bad. The baslast is what the bulb connects to this has a sensor on it that relays voltages and heat back to the main control unit.

Oct 23, 2009 | BenQ SP820 Projector

1 Answer

4-bulb flourescent fixtures flickers before coming on completely


The problem may be related to the balast unit in your light fixture. Check under the cover plate in the middle of the fixture and look for a rectangular (usually black) box. If it has any brown liquid leaking from it then it definately needs to be replaced. Read the label on the box and record the values. Take your stats to the local electrical shop and buy a replacement balast. Installation will require the breaker to be shut off to the circuit. Be absolutely sure you match the wires before attaching them together. Disposal of the old balast must be done through your local recycling center. The material in some of these is quite dangerous.

I would problably suggest contacting an electrician if you are at all uncomfortable with handling a re-wiring job. Good luck with your situation.

OpenSource13

Apr 11, 2009 | Lowel Light Lowel Flou-Tec 450 Fluorescent...

1 Answer

1980 ford f100 choke no voltage


I have somewhat of the same problem but not really. I would check the fuse but you have probably done that. I would run new medium grade wire from powerpoint ( 12V source ) that is hooked up to your ignition. Then run to your choke wire. you can also do a manual set of the choke to get it started. My choke doesn't work at all and needs to be replaced. Having the same starting problem though.

Aug 02, 2008 | 1981 Ford F 100

1 Answer

Rca dlp schematics


what chassis number is your set? Should be an ATC number on the rear of the set. Let me know that number as each series DLP is different for voltages

Feb 15, 2008 | Televison & Video

3 Answers

My samsung dlp tv model hl-p5063 w cuts off multiple times while playing


Hi, I had the same problem on my Samsung.

I removed the rear cover and cleaned the cooling fans, there were (2), it has worked fine ever since.

Be careful of course working with electrical boards.

Dec 01, 2007 | Televison & Video

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

33 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buell Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

jmcpoyle

Level 1 Expert

8 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers

Are you a Buell Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...