Question about 2005 Yamaha Road Star Silverado

1 Answer

How to lower high rpm - 2005 Yamaha Road Star Silverado

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Yamaha Master
  • 1,190 Answers

Wot exactly are you tryin to do that for ? do you have a shaft drive or chain drive rear end ?? P...

Posted on Dec 26, 2013

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ryobi 725r trimmer carburetor adjustment


Turn both low and high adjustment screws carefully clockwise all the way in - do not overtighten.. Then back out each two full turns. Set the idle speed control for highest setting. Prime and start and let it run and warm up for about 15 seconds - then lower the rpms a tad and then adjust the low end screw for highest rpm. Then reset the idle to lower reasonable level. You may have to go back and forth with those two adjustments till it runs fine at low idle speed..

Then accelerate to highest speed and set the high adjustment for highest rpm. Then go from idle to high speed. If not smooth a small adjustment on the high speed screw is in order. Keep doing that until you get a nice smooth transition form low speed to high speed.

Mar 11, 2017 | Ryobi Garden

1 Answer

1992 Vulcan runs great at higher RPM but dies without power at lower RPM?


Not sure what a Vulcan is, but if it has an ignition module these have high rpm and low rpm sections. You low rpm section may have failed. Parts stores can test these if you take the module out and take to them.

Jul 09, 2015 | Cars & Trucks

1 Answer

How do I lower rpm so idle is correct? it's stable around 5k rpm which is too high


Yea, that is way too high. Thankfully your bike is nice and old so idle adjustment is simple. Look for a knob in between the 2nd and 3rd cylinders carburetors. This should be accessible without removing any bodywork, but I'm not certain with your bike. You should set your idle to something between 1~2k rpm when the bike is fully warmed up. If your carb hasn't been serviced in awhile having it idle at 2k rpm will be more stable.

Mar 11, 2015 | 1988 Suzuki GSX 600 F (Katana)

1 Answer

My 1999 zl 440 runs great at 2500 rpm's or higher but any less than 1500 rpm's I need to lift the choke to bring up the rpm's


You have a Blockage in your IDLE JET It is STARVING for fuel, at the higher RPM, the High Speed Jet is able to Provide Fuel but not at lower RPM. You make also have a Damaged Needle and / or Seat.

Feb 12, 2014 | Winter Sports

1 Answer

Car blows white smoke at high rpm runs bad


hmmm...This kind of problem usually is due to cam shaft/valve timing issues. Sometimes, the cam shaft is not properly positioned and is not in sync with the distributor thus the exhaust valves open early releasing unburnt fuel. This will cause the engine to definitely run bad.
I suggest that you try to adjust your engine's timing first (cam and distributor) and then see the results. Also, remember that there is a limit to the rpm that an engine must do- about 6,000rpm is enough for high or max hp. Another information, a camshaft will only work best at a given rpm range so if you run your engine too low or too high, the engine will not work properly. In fact, there are special cam shafts for engines intended to run at high rpm while sacrificing lower rpm levels (the engine runs grumpy at low rpm levels).
Worst case, however, is that white smoke sometimes indicates that oil enters your combustion chamber, this will cost an expensive rebuild if such is the fact.

Dec 24, 2010 | 1996 Nissan Sentra

1 Answer

My mazda 2005 overheat but if i put high rpm like 3000 the temp. go to normal i allready change the termostat and water pump


Sounds like you need a new water pump. When you turn the engine at high rpm's then the pump is pumping faster and circulating the water. But isn't circulating the water good enough at lower rpm's

Sep 16, 2010 | Mazda MPV Cars & Trucks

1 Answer

Idling to high and engine revs from 1000 to 2000 rpm


lower the idle switch,might have to have mechanic do it if u dont know where it is,wont cost alot,very easy

Oct 18, 2009 | 2003 Honda CR-V

1 Answer

High rpm shifting


Does your van have an "EAT" switch -- lower right hand side of instrument panel?

Pressing the switch in changes the shift points by making the transmission shift at a higher RPM.

If the van has the "EAT" switch and it is engaged, try pushing it in again to disengage it.

bikerbc.

Jan 27, 2009 | 1995 Mercury Villager

1 Answer

High Rpm in my toyota Corolla


lower your carburetor gas screw adjuster, there must be 1part gas and 5 parts air.

Jul 11, 2008 | 1991 Toyota Corolla

Not finding what you are looking for?
2005 Yamaha Road Star Silverado Logo

Related Topics:

72 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1147 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...