Question about 2003 Harley Davidson XL 1200 C Sportster Custom

1 Answer

I want to change the battery on my harley. When I disconnect it the alarm goes off

How do I turn off the alarm

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 24 Answers

Pull the side cover off and locate the maxi fuse, then turn ignition key on and then turn it off and pull maxi fuse within 5 sec before system arms.

Posted on Dec 27, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2004 softail springer, engine light goes on then off then stays on. Biker turns over ok but won't start.


Hi Charlie, and the usual suspects are:
1. Fuel tank empty.
2. Fuel supply valve/petcock turned off.
3. Fouled spark plugs.
4. Engine flooded as a result of over use of enrichner.
5. Vacuum hose to fuel supply valve/petcock disconnected, broken, cracked, or pinched.
6. Fuel valve/petcock or filter clogged.
7. Discharged battery, loose, corroded or broken battery terminal connections especially the "NEGATIVE" cable inside the harness at both ends.
8. Loose or corroded wire connection at the coil, battery or plug between ignition sensor and module.
9. Spark plug cables in bad condition and shorting, cable connections loose, or connected to the wrong cylinders.
10. Ignition timing incorrect due to faulty ignition coil, ignition module or sensors (MAP, CMP CKP and/or BAS).
11. Sticky or damaged valve or pushrod wrong length.
12. Primary cam sprocket spline sheared or missing spacer.
13. Security alarm needs a reset.
For more information about your issue, please visit the websites below, and for specific information or questions you can reach me at xlch@mail.com. Good luck and have a nice day.
Harley Davidson Manuals Mark Workshop
Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...

Sep 23, 2015 | Goes Motorcycles

1 Answer

What things could i look for on my 2009 harley davidson super glide as to why my alarm will not shut off and let start my bike


If you are turning the bike on before turning the alarm off that will happen. If not check and make sure that the connection for the alarm has not come loose.

Dec 27, 2014 | 2006 Harley Davidson FXDCI Dyna Super...

2 Answers

How do you reset the factory ignition security system after it has been tripped?


The alarm will reset automatically or you can turn it off with the fob. If you cannot turn it off using the fob, then maybe the fob battery is flat. Replace it with a CR2032 and try again. If the alarm keeps ringing no matter what, then you may have a faulty TSSM module. All Harleys will reset the alarm if bike is turned off and left alone. By the way, have you removed the bike battery? If you have and did not disconnect it correctly (turn off alarm using fob, turn ignition on, disconnect battery) then the alarm siren will sound until its own backup battery goes flat. If this is the case, turn on ignition switch before fitting the battery.

Sep 01, 2014 | 2003 Harley Davidson FXDL Dyna Low Rider

3 Answers

Security alarm problem


Replace the alarm system cos your Harley has probably shook it to death!! Genuinely!!

Mar 13, 2014 | Harley Davidson Motorcycles

1 Answer

2008 electra glide battery draw, test light pulses, now bike wont crank over


The pulsing could be the alarm module. When bike is turned of, you will get small draw for a minute or so and then it should go very low, below a miliamp or so. This is the alarm module setting itself. Check for this. Is battery gone flat while checks were being made? Make sure ignition switch is on when disconnecting battery if alarm (Stock HD) is fitted. If not, alarm module gets confused and can cause problems. The corrct procedure for disconnecting a battery from an alarm fitted HS is - alarm off, ignition switch on, pull main fuse (Maxi Fuse), disconnect battery. To fit, ignition stitch off, connect battery then install main fuse.

Nov 01, 2013 | Harley Davidson FLHTCUI Electra Glide...

1 Answer

Disconnect battery and alarm sounds


Either turn the security system off or remove the battery for the siren. It is in the little black box that controls the siren.

Jan 25, 2013 | 2005 Harley Davidson FXDL - FXDLI Dyna Low...

1 Answer

Speedometer and odometer doesn't work after the battery was changed


Hi Jhuggitt, you may need an alarm reset, try this first, turn the ignition key to on then remove the maxi fuse or disconnect the main circuit breaker and leave the switch on for about a minute, then replace your maxi fuse/main breaker, for more information about your question please visit the websites below. Good luck and have nice day. Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...

Jun 21, 2011 | Harley Davidson XL 883C Sportster Custom...

1 Answer

When changeing battery on 2006 custom 883c '' will i have to reset the alarm or anything '' ??


Hi Lee, it's possible but try this first, turn the ignition key to on then remove the maxi fuse or disconnect the main circuit breaker and leave the switch on, then replace your battery and maxi fuse/main breaker, for more information about your question please visit the websites below. Good luck and have nice day.
Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...

Sep 21, 2010 | 2006 Harley Davidson XL 883C Sportster...

1 Answer

How do i disable alarm on a street gliude. Going on a trip and it will be in the trailer and the lights keep flashing becuase of the movement


Don't mess with alarm parts. Too easy to make it angry.Just disconnect the grd.lead on battery.If alarm goes off when you reconnect grd. just disarm in usual way.Better for battery anyway.

Mar 15, 2010 | 2008 Harley Davidson FLHX Street Glide

Not finding what you are looking for?
2003 Harley Davidson XL 1200 C Sportster Custom Logo

137 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...