Question about Harley Davidson Motorcycles

1 Answer

Turn off alarm without key fob - Harley Davidson Motorcycles

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Harley Davidson Master
  • 1,554 Answers

First off, you need to know the PIN.
Setting the PIN is as follows:

Think of a five-digit PIN, and write it down. Think of this set of numbers as a password for starting your bike and disabling the alarm during those times when you don't have your fob.
Turn the ignition key on, then off, then on, then off, then on again. Then press the left turn-signal switch twice. Press the right turn-signal switch once, and the current PIN should appear in your odometer.
Be sure the first digit of the PIN is flashing. Enter the first digit of your new PIN by pressing the left turn signal to cycle through the numbers.
Press the right turn signal once to switch to the second digit, and select the correct number with the left turn signal. Repeat this process until your new PIN is entered correctly.
Press the right turn signal once, then turn the ignition key off to save the PIN you selected.

Now, how to disable:

Let's assume for simplicity that your code is set at 31313 and you wish to use the manual disarm of the security system using the directional switches as if you lost your fob and cannot disarm the system.

Your security system will disarm the bike and it cannot be started without deactivating the system first.

If you are unsure of what the manual code is refer to the top of this page or check with your dealer and set one if it has not been set by them.

Again this is based on your code being 31313 just to make it easier to understand.

1. Turn the ignition to Accessory.

2. Press both turn signals. (security light should flash rapidly)

3. Press left turn signal button 3 times (the 1st "3" of the PIN). Press right turn signal button 1 time (to "set" the code number).

4. Press left turn signal button 1 time (2nd number of PIN). Press right turn signal button 1 time.

5. Press left turn signal button 3 times. Press right turn signal button 1 time.

6. Press left turn signal button 1 time. Press right turn signal button 1 time.

7. Press left turn signal button 3 times. Press right turn signal button 1 time.

Security light stops flashing and security system is disarmed.

If you've changed the number, use your new number instead of 31313.

Posted on Dec 26, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Turn off alarm without key fob


You can purchase a key fob from your dealer and they will have to program it to your car. The security system can be disconnected but it is not advised.

Mar 22, 2014 | Honda Cars & Trucks

1 Answer

Turn off alarm without key fob


if alarm came with car check with dealer, other than that disconnect alarm from battery

Dec 16, 2013 | Kia Rio Cars & Trucks

1 Answer

Programming keyless remote


Below is a couple proceedures on the subject --first one sets your personal security code in case you lose your Fob or if the battery should die the second one is ASSIGNMENT of a Key Fob to the bike

Below

mail_dir.ashx?url=http%3a%2f%2fwww.fixya.com%2flxp.gif%3ftype%3dimpression%26mailid%3d204&met=0&mt=204 This must be done when you buy a new button type key fob for the Alarm if you lose one.

I assume you know your personal entry code using the directional switches and the key switch to activate , if not , it's in the
Owners Manual

If you never set the code,the dealer can help you out here.

1. Set run switch to off
2. ign to acc
3. hold both turn sigs till lights flash
4. use
Left Turn Signal to enter number by pushing 7 times
5. use right turn signal as enter key
6. repeat until all 5 are entered and you hit enter

lights should flash and you should be OK.


KEY FOB ASSIGNMENT


The Key fob on TSSM motorcycles must be set so it will operate the alarm system on the vehicle.
This assignment must be completed with no pauses between steps greater than 10 seconds.
Turn the ignition OFF after all key fobs have been assigned.
The
programming mode will also exit after 60 seconds has elapsed without detecting any fob signup messages
or turn signal switch activity.
Two key fobs may be assigned to the TSSM.
The first successful attempt to program a fob will disable all previously assigned fobs.
If a second fob is to be programmed, it must be done in the same programming sequence as the initial fob.

Nov 16, 2013 | Harley Davidson Motorcycles

1 Answer

Turn off alarm without key fob


Tracy:

Have you replaced the battery in the fob? After replacing the battery in the fob, the car owner's manual will tell you how to re-program the fob to the car.

Sep 18, 2013 | Pontiac Cars & Trucks

1 Answer

Key fob flashes but wont unlock car vectra sri130 2000


yes then when you get in turn key to number to and press the fob the locks should lock the door and the fob is rest.

Apr 07, 2013 | Vauxhall Cars & Trucks

1 Answer

When we use our key fob to lock the doors, i know we must use the key fob to unlock the doors to avoid the alarm from going off. Recently I parked in a parking garage at an airport (left key fob at home)...


You should be able to just unlock the door with the key, and even if the alarm is still going of try to start it the key should override the alarm.

Sep 15, 2010 | 2001 Toyota Tundra

1 Answer

Hit panic alarm on fob accidentally and wont turn off unless key is in ignition and turned on. as soon as key is removed from ignition panic alarm starts again. fob seems to be not working. can i manually...


reset the computer by disconecting the posative cable for 3min reconect it should cure the problem
if not have a disnostic run most auto parts will do this for free
hope this helps
Please leave feedback

Mar 21, 2010 | 2002 Saab 9-5

1 Answer

Car key fob not working and locking car


i have a rover 25 and the key fob is not opening the car i could use the key to open it but the alarm will go off and cant stop it without the fob...

May 28, 2009 | 2002 Jaguar X-Type

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

201 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...