Question about 2004 Harley Davidson FXDWG - FXDWGI Dyna Wide Glide

1 Answer

Pulling the clutch lever in all the way with the bike in gear and not running,it acts like i dont have the clutch pulled in.will not roll.clutc feels firm.was working when i turned bike off 2 days ago

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

I would check your clutch adjustment you should be able to just stick a nickle in between the housing and the cable end

Posted on May 27, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Transmission issues on a 2003 Buell XB9S Lightning.


sounds like shift lever adjustment problem
take it into a service center and have it properly diagnosed and a quote

Sep 09, 2016 | 2003 Buell Lightning XB9S

1 Answer

My clutch wont engage when i pull the clutch handle to shift. what should i do?


Clutch problem - please help - Dirt Rider Magazine

forum.dirtrider.com/discussion/6668452/clutch-problem-please.../p1

May 11, 2012 - 18 posts - ‎9 authors
If I put it in 1st with the clutch pulled in, it will not roll freely, either the tire will slide ... The cluch is not dis engaging in my opinion. ... it (even with the clutch lever pulled in) the clutch won't disengage, and it will drag the tire or turn the motor over. ... can get notched, however - if your bike shifts into gear (with the clutch pulled in) ... bike not able to roll when in gear even while holding ...
18 posts
Yz 125 new top end, now no clutch?
10 posts
May 3, 2012
2000 YZ 125 clutch problem???
17 posts
May 3, 2012
More results from forum.dirtrider.com

Clutch Problems (Lever Won't Engage Clutch after cable change ...

www.xr1200ownersgroup.com/site/showthread.php?t=12314

Dec 26, 2015 | Cars & Trucks

1 Answer

2002 yz 125 when I put it in gear it will shut off acts like the clutch is not working when I adjust it on the handle bars it slips


Mechanical issue: clutch not disengaging completely...
engine off - put in gear and roll back and forth with clutch released does engine stop the bike from rolling? Now pull clutch lever in and try rolling again is clutch cable adjusted properly?
Electrical issue: bike thinks clutch is still engaged and kills motor when not in neutral
Is the clutch switch properly connected and working? Is it adjusted properly? Use a multimeter to read resistance across switch contacts does it change state when clutch is pulled in?

Jul 28, 2014 | Motorcycles

1 Answer

89 virago 250 clutch sticking


you could try riding the bike in third or fourth gear with the clutch lever pulled in and accelerate

Feb 08, 2013 | 2005 Yamaha Xv 250 Virago S

1 Answer

The only way to shift the transmission into any gear is by holding the shift lever down or up, then releasing the clutch. It then stays in gear. If i just shift (this was working previously) then release...


It sounds like your shifter pawl is broken. It's trying to roll the shifter drum but it's not rolling it quite far enough for the drum to index to the next detent. It is rolling it far enough to put out the neutral indicator light. If this is the problem, a teardown of the transmission is required to repair this.

There is one other possibility. From the foot shift lever, follow the shifter rod back to the shift lever on the transmission. This is the shift lever that connects to the shifter pawl shaft. I"ve seen lots of them get worn to the point that they feel like they are going to fall off. When they get like that, they don't shift well. To repair this, you will have to pull the complete primary to get to it. If the splines on the shaft are worn badly enough, you're back to pulling down the transmission to replace the shifter pawl shaft.

Good luck
Steve

Aug 14, 2010 | 2002 Harley Davidson FLHTCUI Electra Glide...

1 Answer

I put the bike in gear but when i pull the clutch lever in, it wont disengage and stays in gear??


if the clutch lever feels it has plenty of tension, it may just be the clutch plates stuck together from sitting.

Roll start it and ride around while holding in the clutch, vary the throttle, and they usually unstick. Give it an oil change when it warms up.

May 18, 2010 | 2004 Honda CRF 250 R

2 Answers

Start bike in nutral hold in clutch put into first and imediately stalls


G'Day mate,
Sounds like the bike has a stuck clutch, where the pressure plates and clutch plates are not disengaging, probably from sitting for a while. Check the clutch adjustments first to see that you have good operation and tension in the clutch lever. To break it free, try first allowing the engine to heat up to operating temp, this can sometimes allow the clutch to free up with heat expansion.
If you can get the bike to a rolling start(mate pushing) and get into a gear, go roll on and off the throttle a few times with the clutch pulled in, see if you can break it loose. Some peps have success with wrapping wire about the handle bar holding the lever in, and let it sit over night, let the oil into the clutch plates.
Dont get too carried away with dropping it into gear with the engine running. You dont want to do more damage. If it remains an issue, you will have to remove the clutch cover and tear the clutch down. check plates for wear and warping. Replace if required. Good luck with it.
regards robotek

Apr 09, 2010 | 2008 KTM 250 SX-F

4 Answers

HOW DO I SHIFT A 2003 KX 250


pull your clutch in on the left handlebar push the shifter lever down and let you clutch out slowly while giveing the bike a lil bit of gas. But if you don't know how to ride i wouldn't be jumping on a kx 250

Sep 20, 2009 | 2003 kawasaki KX 250

1 Answer

1995 900 sp clutch does not disengage when lever


hi,this may help,it sounds like your clutch plates are stuck together,this is quite common on bikes that have been parked up for a while,mine does it ocasionally,i fix it by getting the bike moving and crash starting it,once you have got it running and moving with the bike in the highest gear you can get it into(you can change up and down the gearbox without the clutch and not do any damage)simply pull the clutch lever in and roll on and off the throttle a couple of times and the clutch should disengage...hope this helps

Aug 02, 2009 | 1998 Ducati 900 SS

Not finding what you are looking for?
2004 Harley Davidson FXDWG - FXDWGI Dyna Wide Glide Logo

Related Topics:

150 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...