Question about 2003 kawasaki KX 125

1 Answer

1994 kawasaki kx100 cant get swingarm bolt out

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 78 Answers

Sound like it sieized in ther try a impack gun on the bolt as i can remmber it runs though the engine case thats wear it could be stuck i would soack it with penatrating fluid give the head of the bolt some nice clouts with a hammer the try a impack gun or large bar

Posted on Jun 26, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

What kind of spark plug fits a kx100, 2000

May 16, 2015 | kawasaki Motorcycles

1 Answer

Bent swingarm

First off the wheelicon1.png will be offset. as well the belt will run on the outside edge of the pulley. It won't run in the middle. Just like if you rotate the wheel in reverse the belt will travel inward on the pulley and remain there until you run it forward again. It part of Harley's design. Also you can't really go off of the adjuster bolts as a guide. They tend to be different. Sometimes the covers just need to be forced away from the wheel too. If the adjustments seem correct then I would try re adjusting the covers or make sure they are spaced out right as well.

Sep 10, 2013 | Harley Davidson Motorcycles

1 Answer

I need to replace the cluch cover on a kawasaki kx 80


Oct 19, 2010 | kawasaki KX 125 Motorcycles

2 Answers

Im trying to replace the swingarm

Is it a through bolt? Does it spin on one end while turning the other? Put the nut back on and tap it with a lead hammer, see if it is just a big bolt, then drive it out the rest of the way with a dowel. Hope this helps.

Mar 25, 2010 | 2004 Triumph Tiger

1 Answer

Gsxr 750 wv swingarm bearing adjustment ?

hi buddy you cant adjust bearings the bearing are there for smooth movement you can losen the swing and arm bolt to make them a little loser but too lose will be dodgy get back to me what you mean

Oct 01, 2009 | 1997 Suzuki GSX-R 750 V

2 Answers

KX100 1998 Don't know where hose from tank goes.


Aug 16, 2009 | 2003 kawasaki KX 125

1 Answer

How do you tighten the chain on a zxr 1100 c3 pls ?

  1. Place your Rex a center stand or rack.
  2. Referring to the Owner's Manual, inspect the chain and sprocket for wear. Replace if necessary.
(Whenever replacing a bike chain, you should really replace both sprockets at the same time, too.)
  1. On both sides of the bike, loosen the large vertically-mounted hex bolts at the very top back of the swingarm.
  2. Noting the alignments marks on each side, place an even larger hex wrench into the side of the circular aluminum insert that's surrounding the axle.
  3. Use the wrench to adjust the chain to about 0.9" (~23MM).
  4. Make sure both side's alignment marks exactly match each other.
  5. Tighten the swingarm bolts down, but not all the way.
  6. Spin the tire around while constantly stopping to check the chain slack. If it's even all the way around, tighten the swingarm bolts all the way. You're done! If not, go to Step 7.
  7. If the chain slack runs uneven around the clock, re-check the alignment marks and re-adjust as needed.
  8. Re-perform steps 3 thru 7 until the chain properly adjusts. Give up after four failures.
  9. If unable to properly adjust, you might need to perform a "string alignment'. Google that, if necessary. It's too complex to put in here.
  10. ALWAYS make sure your Rex's chain is kept clean, and sparingly use a high-quality chain wax every 500 miles or so.

Jun 21, 2009 | 1999 kawasaki ZRX 1100

Not finding what you are looking for?
2003 kawasaki KX 125 Logo

Related Topics:

179 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers


Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides