Question about 2000 Suzuki GSX-R 750

1 Answer

How do i install new brake pads on my gsxr 750 and how diffacult is it is it anything like a car

Posted by on

  • twardowskic1 May 16, 2009

    thank you i will try to them my self it sounds simple

    thank you


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 216 Answers

It quite simple. Loosen the recessed hex bolt that secures the pads but dont remove. Then remove the two bolts holding the caliper to the fork leg and slide away from the disc. Remove the recessed hex bolt and old pads and fit new pads in same fashion as the old pads. You may need to push back the pistons to fit the thicker new pads, be careful not to damage the pistons.

Read the manual for any other problems. Good luck.

Posted on May 16, 2009

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 1997 gsxr 750 srad and it has the standard tokka front break calipers, problem is they stick ,My question is can I fit a different set of calipers and what make are good and will fit .

Hi, Nick those calipers worked fine for 20 years if they are sticking a little rebuild them with a new caliper kit, it;s a lot cheaper for this scenario you will need your service/owners manual if you can't find the first and best tool you ever bought for your Yamaha, despair not, for a mere zero $ you can download another one. For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Brake caliper upgrade
Suzuki GSXR 600 Front Brake Repair and Flush Part 1
Suzuki 1996 GSX R750 Service Manual
OEM parts for Suzuki

Mar 19, 2017 | 1997 Suzuki GSX 750 F (Katana)

1 Answer

F1 code on my 05 suzuki gsxr 750


May 13, 2012 | 2005 Suzuki GSX-R 750

1 Answer

I have a 2005 suzuki gsxr 750 my front brake line got trapped under the front fender and lock the brakes up.why did this happen?

The only thing I can think of it was installed wrong the last time the pads were replaced. If it
is in position and everything is tight, there is know way that could happen . So I would get your
manual and or find the layout design for your brake line and put it back in the right way.

Nov 28, 2010 | 2005 Suzuki GSX-R 750

1 Answer


When you push the caliper piston in to install the new brake pads, you have to keep pumping the brake paddle after the new pads and every thing is put back together, the paddle will come back up, do it with the engine off.

Jul 22, 2010 | 2006 Dodge Grand Caravan

2 Answers

2004 Suzuki GSXR 750 front brakes won't engage

i believe its the disc brake.check for any leakages in the hose connecting the brake pads as well as the oil levels.if its low than the threshold level please fill it up with the recommended brake oil for bike.(usually dot3 or dot4 for disc brakes)
also ensure the brake pads have grooves over it and they are in proper condition.if they are worn out then the disc would be filled with black oily substance.if yes for the previous conditions change the brake pads too.
thanks for contacting fix-ya

Jan 01, 2010 | 2004 Suzuki GSX-R 750

2 Answers

05 GSXR 750 Speedometer Reads 0

I just had the same problem 2004 gsxr 750. After massive troubleshooting and time I found out it was the gauge. So I then ebayed a gauge on ebay and bought on for 290 dollars. Speedo now works. I am just off on the actual speed, need to by a speedo healer.

Sep 17, 2009 | 2005 Suzuki GSX-R 750

3 Answers

How do i change the pads and rotors on my 2002 trailblazer ls?

If you Need Pics/ Illistrations Email

Brake Pads Replacement - Front

Removal Procedure

Caution: Refer to Brake Dust Caution in Service Precautions.

  1. Inspect the brake fluid level in the brake master cylinder reservoir.
  2. If the brake fluid is midway between the maximum-full point and the minimum allowable level, no brake fluid needs to be removed from the reservoir before proceeding.
  3. If the brake fluid level is higher than midway between the maximum-full point and the minimum allowable level, remove the brake fluid with appropriate tool to the midway point before proceeding.
  4. Raise the vehicle. Refer to Vehicle Lifting.
  5. Remove the tire and wheel assembly.

  1. Compress the front brake caliper piston.
6.1. Install a large C-clamp over the top of the brake caliper housing and against the back of the outboard brake pad. 6.2. Slowly tighten the C-clamp until the piston pushes into the brake caliper enough to slide the brake caliper off the rotor. 6.3. Remove the C-clamp from the brake caliper.
  1. Remove the lower mounting bolt from the slide pin.
  2. Rotate the brake caliper upward until it stops.
  3. Remove the outboard brake pad.
  4. Remove the inboard brake pad.
  5. Remove the brake pad retaining clips from the brake caliper mounting bracket.
  6. Remove the brake pad retaining clip from the brake caliper.
  7. Remove all foreign material from the brake caliper using denatured alcohol.
Installation Procedure

Important: When installing new brake pads, DO NOT reuse the old retaining clips for the brake pad. Use only NEW brake pad retaining clips.

  1. Install the brake pad retaining clips to the brake caliper mounting bracket.
  2. Install the brake pad retaining clip to the brake caliper.
  3. Ensure that the brake pad retaining clip in the brake caliper is properly seated.
  4. Install the inboard brake pad.
  5. Install the outboard brake pad.
  6. Rotate the brake caliper down into position.

Notice: Refer to Fastener Notice in Service Precautions.

  1. Install the lower brake caliper mounting bolt.
    • Tighten the brake caliper mounting bolt to 51 Nm (38 ft. lbs.) .
  1. Install the tire and wheel assembly.
  2. Lower the vehicle. Refer to Vehicle Lifting.
  3. Fill the brake master cylinder reservoir. Caution: Refer to Firm Brake Pedal Caution in Service Precautions.
  4. Pump the brake pedal slowly and firmly to seat the brake pads.
  5. Burnish the new brake pads.


Jul 24, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

Excess travel on front brakes of a gsxr 750 ws

You need to make sure master cyl clean possibly needs new seals or master cyl,but try this remove pads keep pumping cyl so that pistons come out further place some wood or plastic between disc and pistons thinner than your pads that should stop your pistons coming out and will allow more fluid into the caliper,then press the pistons back to return fluid back up pipe to pressurise valve good luck it may not work first time just keep pumping .

Apr 25, 2009 | 1995 Suzuki GSX-R 750 WS

2 Answers

Gsxr 750 rear brake


bike brakes are a pain to do man!! id use a bleeder kit on it and if this doesnt work then your master cylinder at the pedal is gone!! iv a fzr600 race bike and thats ten times worse man

Aug 29, 2008 | 2002 Suzuki Aerio

Not finding what you are looking for?
2000 Suzuki GSX-R 750 Logo

Related Topics:

281 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts


Level 3 Expert

75807 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides