Question about 1990 Yamaha XT 600 E

1 Answer

Gears not engaging from 1 to 5

Recently had engine rebuilt and whilst riding no gear seemed to work

Posted by on

  • Caber_Feidh May 11, 2010

    Case assembled wrong. Most likely shift drum binding, or incorrect fork install.

    Would need more clarification to be much of a help, is it "clicking" into the detents and just staying in one gear, or stuck in N?


×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 216 Answers

Take it back to the place/person who re-built the engine.

Posted on May 16, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Engine start Bendix still engaged put into any gear Bendix disengages can go back to park there will be no more problem


if your saying your starter stays engaged after starting engine till you cycle thru the gears , your starter needs serviced , most likely a worn bendix pivot bushing

two options 4 repair
1= replace starter
2= remove starter and have it professionally rebuilt then reinstall it

Sep 14, 2015 | Cars & Trucks

1 Answer

I have a zafira club 1.6 which seems to have no 5th gear. I can enter 5th whilst driving without the clutch. Any ideas please.


because of the close gear ratios and the synchronisation action ,it is possible to change gears without the clutch if the engine rpm's and road speed are close matched. If you put it in 5th gear and the engine rpm's increase without an increase in road speed (gear does not engage) then it is possible that the gear on the out put shaft is stripped. This is a common problem in vehicles where 5th gear is engaged and the vehicle load and speed is excessive inducing excessive wear on the teeth of the gear causing them to fail

May 02, 2014 | Cars & Trucks

1 Answer

I have Toyota Land Cruiser Model S-HDJ81V-RNPCX (1 HD-T) and recently I was doing a major overhaul the engine, everything was fine except the gear. It's seem like gear 1 and gear 2 didn't work. Looks


check that you have hooked up all the cable connections properly. run fault codes and look for TCM problem. Have a pressure test done on the transmission as there may be band/clutch adjustment problems.

Jan 31, 2014 | 2001 Ford Escort ZX2

1 Answer

Fourth gear not engaging


some possibilities are the syncro energise spring has come out and not spinning up the gear to allow engagement Prove by engageing and dis engaging with engine stopped and foot on clutch or the hub has been put in back to front or the selector fork has been fitted inncorrectly

Jan 13, 2013 | 1999 Mitsubishi Eclipse

1 Answer

1998 GS manual Previa with 140k on clock. Has recently started slipping in 4th gear - if changing up from 3rd or down from 5th its asthough something isn't engaging and no further power from the car can...


Sounds like your transmission has come to the end of its life. You can try getting the transmission flushed , and an additive I.E. No Slip added. That might cure some of the problems but obviously if its slipping the clutchs inside are worn out and transmission needs an overhaul.

Mar 15, 2011 | 1996 Toyota Previa

1 Answer

Gearbox engagment


i cant solve this i got the same problem did u ever solve this. i have changed - clutch,slave an master cylinder and the gearbox has been rebuilt

Dec 11, 2009 | 2000 Mini Cooper

1 Answer

MTD mower won't engage traction belts


Check to see if rear axle is broke. Jack up the rear of the tractor, put it in gear and spin one of the rear wheels, the one on the other side should spin the opposite way. hope this helps

Jul 13, 2009 | Garden

1 Answer

1998 ford ranger 3.0 motor auto.transmission slips driven cold


what is the (revolutions per minute) rpm of your engine when the torque converter engages, was the torque converter rebuilt too? what type torque converter is in the ford ie low stall where it engages the gear box at around 900 to 1000 rpm. has there been any power band adjustment by the company that rebuilt your automatic transmission after the insallation.

Jan 02, 2009 | 1998 Ford Ranger SuperCab

Not finding what you are looking for?

Open Questions:

See all 1990 Yamaha XT 600 E Questions

1990 Yamaha XT 600 E Logo

Related Topics:

84 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...