Question about 1999 Yamaha XT 600 E

1 Answer

Cant get a spark on my recoverd xt 600 4pt

Hi any one want a challenge the problem is i can not get a spark, most of the wireing has been chopped out, i am left with no lights no turn signal i have got power to the coil & tdi could any one help me with the
minimum amount of wireing i need to get my bike started again i have been working on this bike for well over two months solid day and night
before work and after and giving the missis a headache to and now she
dont even make me a cup of tea when im out there now, pleeeeease help
the man with no bike no wife no tea no life just basic wires left

Posted by on

  • squif May 15, 2009

    Thanks anyway back to it then. F M X 650 very nicemagic for a yeti sob.sob. I have downloaded a manual now ill try again but basicly i am trying to find out how to (shush), warm wire it, as the clocks are missing no ign or lights, to see if the old heart is still worth saving,wires back to their original destinations? not just yet thats most of the problem, where? ta again im off ohms testing,

  • m_mcneley May 11, 2010

    A silly question, have you connected all the wires back to their original destinations via **** end connectors or what ever it takes? Have you checked all the grounds? Alot of times this is the simplest overlooked problem (even if it looks good it may not be and should be ohms tested for continuity). Some models have sensors/switches for break lite activation that will falter entire electrical systems when failed. Have you purchased a shop manual and ohms tested all electrical components (electrical tolerences and prociedures are in the electrical section as well as wireing scamatics? Your local dealer can get you the shop manual u need. I hope this helps. Good luck.

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 42 Answers

Sorry to hear of your nightmare with the recovered XT, i,m afraid your best bet is to download a manual, now there are a couple of sites out there that let you for free, usually in PDF format and obviously copies, but atleast you would then have a diagram. I can't help further as there may be other components needse or missing that are important even on a basic torky single like yours. I ride an FMX 650 but i like the Yammy and its alot lighter than mine. Best wishes - the Yeti - Hastings

Posted on May 14, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Left side turn signals not working


Hi Anonymous, you could have a faulty module, check your wiring and connections from the turn signal switch to the turn signal module with a testlite. Make sure all connector pins are corroded, broken, or loose. For a free wiring diagram please visit the website below:
Harley Davidson Wiring Diagrams and Schematics

Nov 19, 2013 | 2000 Harley Davidson FLHTCUI Electra Glide...

1 Answer

No left turn signal or indicator


Hi Anonymous, start by checking for continuity at the turn signal switch, then check the wiring harness connector to your turn signal module for corroded, broken or loose pins and the red key light is your security alarm indicator light, for more information on your question please visit the websites below and good luck:
Harley Davidson Wiring Diagrams and Schematics
Harley Diagnostic Codes 04 to Present

Jul 04, 2013 | 2006 Harley Davidson FXDBI Street Bob

1 Answer

I replaced my turn signals in my 84 nighthawk w aftermarket one and chopped of my rear liscence plate mount and light now i cant get my new turn signals or front one to work at all. All that happens is the...


cheak to make sure they are wired correctt it sounds like you might of crossed some wires does the indicatoer stay lite when the turn switch is off that would licnence plate light hooked into signal

Mar 06, 2013 | Honda CB 700 SC Nighthawk Motorcycles

1 Answer

Recently my signal lights quit working properly. when button pressed, emergency lights front and back would come on. no left/right signal or brake lights would come on. replaced the tsm. problems...


Hi Ruben, always check fuses and bulbs first, you could have a faulty turn signal module or a bad turn signal button/switch, remove it from the switch housing and check for continuity, check your wiring and connections from the turn signal switch to the turn signal module with a testlite. Make sure all wires are not worn or pinched and connector pins are not corroded, broken, or loose. For a free wiring diagram please visit the website below:
Harley Davidson Wiring Diagrams and Schematics

Apr 01, 2012 | 2001 Harley Davidson FXDWG Dyna Wide Glide

1 Answer

Front left running light burns too bright and left rear blinker blinks faster.


Hi Kevin, you have the front left turn signal bulb installed 180 degrees out or your wiring is bass ackwards. Good luck and have nice day.

Mar 10, 2012 | 2008 Harley Davidson FLSTC Heritage...

1 Answer

1988 jeep comanche wiring


drove mine to the ends of the earth,
there are 4 books,
big main , engine,and one for trans, no PDFs back then so, none sold. just paper books.
its and old car, very old, not too many left run 1988
with that nasty French REniX EFI system/.end rant
I had the 1988 XJ too, a pair of jeeps. then....


i can see your wiring is all messed up
and grounds.

got a voltmeter,
if not only guessing and wire inspections may work
ever consider get a sparks guy to fix it? He can and easy.
I promise.
for me to teach you electrics in this box, is over the top hard.

id have inspected all those wires, every inch
and #1 is trailer wiring hacks at the rear.
the tails are not tails
if you its Parking lamp after the front parking lamps or side markers can not be called TAIL,but yes, some fuses are still using the old 1884 now TRAIL name
check fuses yet, means test them ones that look good test.
using a METER.

.
.i see there are shorts on the KEY switch IGN out pin
for sure.!! radio is off key OUT and off.
or that wires IS SHORTED
harness messed up near steering/cluster,big time.

Feb 28, 2017 | Jeep Comanche Cars & Trucks

2 Answers

Doing research for a law firm regarding an accident involving a Caterpillar 55 Challenger. Question is if the Challenger had it's four-way flashers on, would the turn signal still work?


Four way flashers and turn signals are typically on the same circuit. If this is the case than no the turn signals would not work since the turn signal switch has been bypassed by the four way flasher.

I wiring diagram for this model would confirm whether or not it was wired in the above fashion.

Jan 19, 2012 | Cars & Trucks

2 Answers

1969 ford mustang mach 1 brake / stop light switch challenge


Most tail light problems are a result of a bad ground......somewhere.

Sep 16, 2008 | 1966 Ford Mustang

Not finding what you are looking for?
1999 Yamaha XT 600 E Logo

206 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...