Question about 2008 BMW G 650 Xmoto

1 Answer

BMW Xmoto Fuel Injection Question.

I just purchased a 2007 BMW Xmoto, I notice that a rubber hose runs from the fuel injector body back to an instrument located on the right hand side rear subframe. The hose in my case is not connected to this instrument, it has a plug in it. My initial thought was that it should be connected to the instrument as its part of the fuel injection system but am wondering if there is a reason why the hose is not connected & plugged off. Can anyone advise me, Thanks, Joe

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 3 Answers

If you are talking about the cylinder looking thing it is a charcoal cannister that is just an overflow for the gas. you can actually remove it if you like. if you do, just try not to overfill your gas tank. some people prefer to remove it because they don't like the way it looks. personall,  i like it, so if you do, just hook the hose up to the bottom of the cannister.

Posted on Sep 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Yamaha YBR 125 2007 not starting, it been standing for 2 years


the fuel pump is most likely seized from setting too long. fuel injectors could be clogged as well.

Apr 12, 2014 | 2007 Yamaha Ybr 125

1 Answer

My Yamaha YBR 125 2007 not starting, it been standing for 2 years, I have cleaned tank, all hoses, filter, fuel injector.


Hi sounds like your nearly there ,try swapping hose around ,I once mixed the in and out ,next did you take the carbs apart and clean ,also a small shot of wd 40 in to the fuel pump without hose connected then pour out ,from what I read sound pretty good kid best of luck

Apr 12, 2014 | 2007 Yamaha Ybr 125

1 Answer

I own a 1990 Chevy Lumina APV 3.1, was leaving for an interview. Suddenly my gas peddle was useless. checked for fuel in tank, made sure spark was there an timing was firing, listened for fuel pump, &...


if it's a trottle body with two injectors.remove fuel pressure,Remove the air filter, remove connector from injector,remove the center pin that hold the air filter case.than remove the top injector from tbi,than pry the injector out,

Aug 02, 2013 | 1990 Chevrolet Lumina APV

1 Answer

Tried to repair a gas leak under car . we tried to repair the hose now it doesnt leak from above the hose only under and used 2 clamps and it is tight as we are able to get it is it the metal piping ?


you don`t say what type of fuel system you have,carburetor or fuel injection,throttle body or port fuel injection system.this determines the type of repair.if it is port fuel injection then you cannot repair with a hose,it must be repaired with a steel line as the fuel pressure is above 30lbs pressure and rubber hose is not strong enough for the pressure.you can replace the section of line that is bad with a new steel line connected to a good section.if it`s carburetor the pressure is only about 6 to 8lbs pressure,and a hose can make the repair.if it`s throttle body then the pressure can range anywhere from 15 to about 20lbs pressure,this can be repaired with fuel injection gas hose,so you can see it makes a difference what system you have.any rubber hose used must be a fuel line hose not just any rubber hose.

Mar 15, 2011 | Chrysler New Yorker Cars & Trucks

3 Answers

How do I know if my truck has a carb or if it's fuel injection?


FUEL INJECTION THROTTLE BODY INJECTION SYSTEM HAS TWO ROUND FUEL INJECTORS ON TOP.CARBURETOR DONT HAVE FUEL INJECTORS.IT HAS CHOKE VALVE AND FUEL NOZZLE WHICH IS THE FUEL METERING SYSTEM.

Feb 04, 2011 | 1987 Nissan Pickup

2 Answers

Hi my bmw 316i 1600 with a e36 engine is only doing about 10 to the gall, any ideas, also notice a strong smell of petrol when first starting car and smells stays there for about 15 mins, and also notice...


run the fault codes
problems with running rich include:-
injectors not working properly
excessive fuel pressure
leaking injector seals
heated oxygen sensor failure ( they are located in the exhaust manifold /pipe before the cat converter and are used to read the exhaust gas composition and report to the ECM which adjusts the air/fuel mixture accordingly
ambient air /BARO sensor which report the air temp/pressure to again allow the ECM to set mixture
The strong fuel smell can be from fuel leaks , flooding --as stated with injectors or an EVAP system vent solenoid problem
The first 4 possibles would be the most obvious place to start especially with a fault code reading

Nov 19, 2017 | BMW X3 Series Cars & Trucks

1 Answer

Where would i locate the fuel filter on a 1999 Ford taurus Se at?


Fuel Injection
General Information (System Description)
Electronic fuel injectors for all gasoline engine applications are basically
the same. They consist of an injector body, an electric solenoid, spring, nozzle
and a filter. The injector is supplied a constant supply of pressurized fuel
from the fuel system. The primary function of the fuel injector is to atomize
gasoline into the surrounding air at the proper time. Throttle body injectors
atomize fuel into the intake manifold in much the same manner as a conventional
carburetor (wet intake); port fuel injectors direct the atomized fuel at the
back side of each cylinders intake valve(s) (dry intake). Gasoline direct
injection systems operate at substantially higher pressure and direct the
atomized fuel directly into the combustion chamber of each cylinder.
---
Az Filters/Fuel Filter
Part Number:
FF679
---
The Fuel Filter is located: Under vehicle, passenger side, below seating area, passenger side of fuel tank, mounted on frame in fuel line

Oct 28, 2010 | Ford Taurus Cars & Trucks

1 Answer

Bmw 325tds diesel flowing back to tank when parked


usual problem ,valves in injector worn for the fuel pump.easy quick fix this one ,fit a non return valve in the inlet pipe,check flow direction on valve when fitting and evan better as well is another in the bleed off return pipe .valves available from a motor factor or a specialist garage like bosch or lucas ,cut pipe and fit the valve with a piece of rubber pipe to connect the valve in line.or listen to the people who want to milk the golden cow and have the whole injector pump overhauled .

Dec 23, 2009 | 2001 BMW 325

1 Answer

Idling and shutoff issues


They have stabilzer with ethenol treatment in it as well .. I use that too..
Put some good 91 gas in it and you should be good, new plugs..

Sep 20, 2009 | 2007 BMW G 650 Xmoto

Not finding what you are looking for?
2008 BMW G 650 Xmoto Logo

Related Topics:

194 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4982 Answers

Mike Gilbreath

Level 1 Expert

50 Answers

yadayada
yadayada

Level 3 Expert

80339 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...