Question about 2002 kawasaki ZZR 400

1 Answer

I nead kawasakizzr 400 cc valve seals&gaskit

I nead kawasakizzr 400 cc valve seals&gaskit

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 434 Answers

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

106 model coldspot

If your asking how, then on this model I think they just push into a slot, if not check for screws & a plate holding it in. Pull or unscrew the old one & reverse the process for the new one.

Nov 19, 2013 | Indesit C133 Bottom Freezer Refrigerator

1 Answer

I am getting coolant into the oil on my drz 400 .i dont think it is the head gaskit , could it be the watr pump seal

It could be the water pump seal, however there is usually a small space and teltale hole where coollant will drip from before it gets to the oil seal.

Aug 07, 2011 | Suzuki DR-Z 400 Motorcycles

1 Answer

Replaced my Moen cartridge, finally got the leaking to stop, but now have no hot water no matter which direction the single handle is positioned

Turn on hot water supply

ok to easy but maybe

take valve cartridge out of valve It may be put in 180 degrees out

compare cold side inlet to warm side inlet: spring, little black gaskit/s seal maybe a ball/s

The cold side works right

Nov 28, 2010 | Moen & Replacement Cartridge

1 Answer

Volume of fork oil needed per fork for a 1986 VF 400 nc 13

Well, when you take off the fork make sure you empty it first before anything else then make sure that the fork pressure spring is released before changing the seals. The fork oil amount should be no more than 200 cc or no less than 190 cc

Jun 24, 2010 | 1986 Honda VF 400 F

1 Answer

I have oil runing into the this a head gaskit or something biger?

It could be valve seals which can be replaced with the heads still attached to the engine block. If compression is good I would investigate that first

Mar 26, 2010 | 2002 Dodge Neon

1 Answer

Oil Pan Gasket Leak

you oil pan bolts of the bottom of the oil resivour the gaskit fits in between the surfaces where the pan meets it creating a seal witch in your case needs to be replaced this procedure replaces that gaskit to create a new seal

Mar 04, 2010 | 2001 Ford Ranger Regular Cab

1 Answer

1994 arctic cat zr440 right seal behind stator is leaking. cani pull it off and replace it or do i have to tear it down

to replace that seal you do not have to overhaul the motor. but you have to drain the coolent and place the motor up side down and open the crank case and pull the stator of as well as the internal coil pack. the internal coils and stator must be off befor you can open the crank case. replace that seal and get black form a gaskit and put her back thogeather and you should be good to go

Feb 23, 2010 | 1979 Suzuki GS 400 E

3 Answers

I just replaced the gasket of the transmission pan and still have a leak on my 1999 chevy suburban?

The leak is coming from the pan ??
Maybe the leak is traveling to the pan seal area from somewhere else ?
Did you scape off the stuck-on old gaskit on trani and pan ?
Its customary to use gaskit sealer on both sides of the new gaskit..

Aug 13, 2009 | 1999 Chevrolet Suburban

1 Answer

I nead kawasaki zzr 400 seal oil,valve guides& head gas ket

have it taken to a shop before someone takes you for your money.

Jun 17, 2009 | 2001 kawasaki ZZR 400

Not finding what you are looking for?
2002 kawasaki ZZR 400 Logo

Related Topics:

121 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers


Level 3 Expert

76109 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides