Question about 2000 Yamaha XV 125 - S

1 Answer

Yamaha Virago XV125 2002 Clutch not releasing when leaver pulled

The Clutch on my Virago xv125 does not completely release when the clutch leaver is pulled .. I can push it forward quite easily in use the starter it cuts out, suggesting it is not completely releasing.. I have set the leaver free play to 10 to 15 mm as specified in the handbook.. Does anyone know where I can get a service manual for this model?

Posted by on

  • ra77929 May 14, 2009

    Thanks Tim for the Info ...

×

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 200 Answers

You can download a free manual at carlsalter.com
good Luck to you friend....Tim

Posted on May 13, 2009

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Yamaha wr200 bike clutch fitment


take clutch case off , you then see the clutch basket and you need to remove the center plate with about 6 bolts , then remove the fiber coated plates along with metal plates .. then replace first a fiber coated plate followed by a metal plate then a fiber following this until all plates are in and a fiber plate is showing ! then replace the cover plate with 6 bolts , tighten all bolts then undo the center nut with the adjusting screw and back it off until there is slight free play on the clutch leaver as you pull it and then release! lock the nut up holding the screw and try ! soak fiber plates for an hour before installing also ! cheers

Dec 04, 2013 | Motorcycles

1 Answer

So duan3longwo how do I know if the clutch is adjusted right on my 89 Yamaha virago 1100? If the clutch cable it's good at the lever could it still be off a little at the crank case? Since it's a wet...


A proper adjustment will have a cable that has just a little slack. It has to completely release the clutch, and completely engage it. Low oil may affect it, too much oil will be struck by the crank and foam up.

Nov 27, 2013 | Motorcycles

1 Answer

1982 Yamaha virago 920 clutch switch


you have a short out in your wiring maybe
try by passing the switch
ie take the wires off and connect them up
if it still does not work disconnect the wires

Feb 20, 2013 | 1982 Yamaha Virago Xv920 Xv 920 Y153 Air...

1 Answer

Do i need to be in gear to adjust clutch


In the past when I adjusted the clutch on my Virago, I would have the bike in gear...with engine off, make sure pulling in the clutch allows the bike to roll..... Then with the engine running I would adjust for the point at which the clutch would begin to engage upon release. Make sure when released, the clutch is fully engaged and isn't slipping.

Sep 01, 2012 | Harley Davidson Motorcycles

1 Answer

Bike cuts out after selecting 1st or 2nd gear


Hi, Graeme I would take it for a nice long ride the clutch will free itself up for more information about your question and valuable "FREE" downloads that you will need please visit the websites below. Good luck and have a nice day.
http://www.xs11.com/forum/showthread.php?t=39074
Fix sticky motorcycle clutch
https://www.tradebit.com/filedetail.php/2864660-yamaha-fzr-600-service-repair-manual-pdf
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-fz-owners-manuals

Mar 18, 2012 | 1990 Yamaha FZR 600

1 Answer

Bike starts in neutral but dies when shifted into gear. because of this I replaced the clutch plates and springs, but no change yamaha virago 700 1985


Check your kickstand switch. It will not allow the engine to run in gear when you release the clutch lever. It may be gummed up.

Aug 09, 2010 | Yamaha XJ 700 S Maxim Motorcycles

1 Answer

Charging Issues 1983 Virago 920 midhight


Are the handlebars on rubber mounting? They may be grounding through the clutch cable. Check for a loose grounding wire in the headlight housing.
The alternator is a 3-phase unit--if one or two of the phases have open wiring or bad rectifier (total of 6-diodes) sections, the voltage output will be reduced. When the engine is released from load (clutch), the engine speeds up making more voltage.

Sep 06, 2009 | 1994 Yamaha XV 535 Virago DX

2 Answers

Yamaha XT 125 Clutch Problem


change the clutch basket and buy a new cable they get stretched out and the basket gets worn severly

Apr 26, 2009 | 2006 Yamaha XT 125 X

1 Answer

Neutral Light Stays On Permanently - Yamaha XV125


it'll be a wire going into the crankcase which has probably been pulled out of the switch i think the switch is on the left side towards the back.



failure to locate it, just remove the bulb and live without it. you will soon get used to feeling when neutral

Apr 03, 2009 | 2000 Yamaha XV 125 - S

Not finding what you are looking for?
2000 Yamaha XV 125 - S Logo

696 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts

dhnguyen

Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers

Tony

Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...