Question about 2008 Keeway Arn 125

1 Answer

My keyway security isn't working proper and shuts down motor bike

My security is being held to control and deny freedom of bike but for those who that want a bike to mental abuse to sell/ Security of shutting motor bike off.....and deny it to start......on and off game....

Posted by on

  • Anonymous Mar 14, 2014

    selling of bikes

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 200 Answers

If you have 2 wires on the positive (red ) side of your battery disconnect the smaller one and try it...this should be your sec sys hookup....i have found the whole system either behind your headlight or under your seat....unplug the whole system if the shortcut doesn't work....Good luck to you friend....Tim

Posted on May 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

JUST REPAIRED BROKEN WIRE LEADING TO MY KICKSTAND BIKE WILL START IN NUTRAL BUT SHUT OFF WHEN PUT IN GEAR ALSO IM HAVING PROBLEM WITH BATTERY NOT RECHARGING ON THE BIKE


Your bike apparently has a safety mechanism where the engine shuts off while in gear, if the side stand is extended. The wire you fixed may not have been fixed properly. There is a switch at the end of that wire which senses the kick stand position. See if that switch is working properly. You can bypass the switch by shorting the wire, but remember it's a safety mechanism and it's better to keep it fixed.

Oct 26, 2014 | Motorcycles

1 Answer

Yamaha ZR


The gear maybe held in place by a KEYWAY or Pin. If it broke then the gear will just spin on the shaft and not propel the bike.

May 06, 2014 | Motorcycles

2 Answers

How to Recover accidentally deleted data from formatted Linux partitions.


You can also try to use a very effective and affordable application for Linux Data Recovery from here:- Linux Data Recovery

Apr 18, 2014 | Computers & Internet

1 Answer

Charging problem Motorcycle


you need 12.6 to turn on the regulator to allow it to charge at 14.25..and than should read 13.75 on shut down..till the battery cools back to 12.6....no 12.6 no charge...new battery needed

May 05, 2013 | 2000 Honda VTR 1000 SP-1 (RC51)

1 Answer

Walking belt slip, sliding away!


You need to replaced the walking belt and have a professional reset the drive belt to the proper tension.

Aug 01, 2017 | HEALTHRIDER S300i Treadmill Motor Control...

1 Answer

CAR SHUTS OFF AT STOP LIGHTS


If it stall coming to a stop it could be that you idle air control motor isn't working correctly. The IAC it a motor that allows air to bypass the throttle plate when the throttle plate is closed. As you come to a stop the motor opens up to allow air in if this isn't occurring the engine will stall as it has no air for combustion to occur.

May 22, 2012 | 2002 Mercury Sable

1 Answer

My maxpro treadmill was wroking for about 6 mins before it jumped from speed 6 to 14 then completely shut down it is now showing an E1 message. i have read a few comments other people have made with...


Hi,

I am sorry for the delayed response as i was not at my desk.

This is a common problem on these treadmills.You will need to check the speed sensor for proper alignment and function. it should be located near the front roller or mounted on the motor. It should be within a credit cards width of the magnet or toothed wheel. If properly adjusted check with an ammeter to see if it is opening and closing by manually spinning the front roller or motor flywheel. If it isn't replace the sensor. If it is functioning make sure you are getting 5vdc to it across the wires. If you are not replace the upper control board(console). If you are getting the proper voltage then replace the lower control board(motor controller).

Let me know,once done so that we could proceed further.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Oct 24, 2011 | Exercise & Fitness

1 Answer

The motor and light work but chain does not move. It is on the wheels and I cant see any problem. At first it would only raise door three or so inches now not at all. I thought manual handle might be...


Look at the drive moter sprocket to make sure that it is properly locked to the drive shaft. they sometime have a set screw locking the sprocket to the drive shaft. It also could be that the drive sprocket is locked down to the drive shaft with a set screw and a keyway. A keyway is a slot milled into the shaft to accept a square piece of square metal. Their is also a small keyway milled into the inside deminsion of the drive sprocket allowing the drive shaft to drive the sprocket.

Mar 16, 2011 | liftmaster Chamberlain Garage Door Opener...

Not finding what you are looking for?
2008 Keeway Arn 125 Logo

Related Topics:

282 people viewed this question

Ask a Question

Usually answered in minutes!

Top Keeway Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4521 Answers

Ron Stone

Level 2 Expert

197 Answers

Are you a Keeway Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...