Question about 2002 kawasaki VN 800 A Vulcan

1 Answer

Front axle came out of my kvf 650 4x4,is it just like some type of o-ring that holds it in place or would i have to buy new shaft?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 93 Answers

Probably a snap-ring. Check with the dealer for one.

Posted on May 09, 2009

  • Dewi Foel
    Dewi Foel Oct 26, 2013

    dont buy a new shaft if it is similar to a kvf 360 it is held on by a spring inside the collar replace the spring and you should be good to go

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ford f150, drive shaft from transfer box to cv axle slides out, what is supposed to hold this in place, front passenger side, 4wd 1999.


It is held in place by an internal snap ring. It sounds like you may have a worn transmission case where the snap ring snaps in. Other issue like suspension modifications can cause thwe axles to pull out as well.

Jun 22, 2016 | Ford Cars & Trucks

2 Answers

How do you pull a 1979 gmc jimmy 4x4 rear right axle


QU40221 19 Spline Outer Axle Shaft for 1977 to 1991 Chevy, GMC Corporate GM 10 Bolt Front Axle is a genuine original equipment outer axle stub shaft for all GM 10 Bolt front axles in 1977 to 1991 Chevy Blazers, GMC Jimmys, and Suburbans, plus Chevy, GMC 4x4 1/2 ton and 3/4 ton Pickups. The splined end on these new axle shafts has three snap ring grooves in three places so they are compatible with all types of automatic and manual lockout hubs plus all full-time solid splined drive gears.

Also available while supplies last: QU40221U Used Outer Axle Shaft with 3 snap ring grooves and QU40660UUsed Inner Axle Shafts with 2 snap ring grooves (QU40660U is not compatible with automatic locking hubs)



see this vdio

Apr 01, 2015 | GMC Jimmy Cars & Trucks

2 Answers

Front differential diagram


Looks like you have your answer. most toyota's I have dealt with were full floaters, no lock ring needed. good luck

Mar 31, 2014 | 1993 Toyota Pickup

1 Answer

Front passenger side broken axle


Need to replace the drive shaft. Aftermarket parts work fine. The biggest issue is removing inside connection to the half shaft. The clip ring tension is stronger than the boot holding the inboard joint on the drive shaft. To break it loose get a large screw driver and from under the car in front hit the inboard joint hard several times until it over comes the clip ring. Remember... always use jack stands when working under the car.

Aug 12, 2013 | 2005 Acura TL

1 Answer

Front axle 2002 highlander


to remove front axle.to loosen front axle nut leave vechicle weight on wheel then just loosen front axle nut because axle nut torque at 217 ft lbs torquehard to loose axle nut with vechicle weight off wheel.okay. you need a 1/2 breaker bar and axle socket to loosen axle nut dont use 12 points sockets need go auto parts store buy right socket for axle nut.okay when you loosen front axle nut you need safely raise support vechicle. need to remove wheels remove fender apron seal remove transaxle fluid remove transfercase oil if you have 4WD.remove hub nut remove stabilizer bar link remove speed sensor remove tie rod end remove lower arm from the ball joint then slide the halfshaft from the hub then carefully pry the shaft from the transaxle.then install new front axle push in make sure front axle snap ring on front axle snap in place inside transmission just pull a little on front axle make its in place. when all done tighten front axle much as you can then when done putting every thing back in place.lower vechicle need torque front axle nut to 217 ft lbs.

Jan 12, 2013 | 2002 Toyota Highlander

1 Answer

How do i repla


replace front axle shaft you need to loosen axle nut with vechicle weight on the wheel just unloosen axle nut dont take axle nut all the way off just loosen it enough first remove hub cap to loosen axle nut.once loosen then raise vechicle remove wheel tire.you need to remove loosen brake caliper bolts just move brake caliper out of way support caliper piece of wire dont have to disconnect brake caliper hose just move it aside let it hang with a piece clothe hanger or piece or cord dont hang caliper by brake hose will damage brake hose.you need to remove brake caliper mounting bracket.go ahead remove axle nut.you have to remove steering knuckle bolts pull steering knuckle out of the strut bracket.you can remove front axle shaft by using large pry bar to the inner cv pry inner cv joint use a little leverage front axle should pop out.when you install new axle shaft push it in place until you hear it snap in place try pull by hand make sure half shaft in place. when done axle nut torque is 191 ft lbs.strut bracket bolts torque at 133 ft lbs.if this is your first time working on vechicle let a garage do the job.but buy the new shaft then take it with you for garage to replace be cheaper take own parts help cut down costs for part just pay for labor.

Apr 05, 2012 | 1994 Chevrolet Beretta

2 Answers

How to change cv joints


I would replace the complete axle assembly,
it would be cheaper and come with a warranty.

Instructions
  1. Remove the CV Joint
    • Remove the boot straps from the CV joint using a standard screwdriver or a pair of diagonal cutting pliers.
    • Slide the boot back over the interconnecting shaft.
    • Get Chevrolet Info at InsideLine Free News, Videos, Photos & More!
      Detach the stop ring at the base of the CV joint assembly using a pair of snap ring pliers.

    • Pull the CV joint assembly from the interconnecting shaft to force the snap ring at the top of the shaft through the CV joint assembly.
    • Tilt the inner cage (the cage holding the balls in place inside the housing) in different angles to remove the six balls. Use your thumb or a hammer and a wooden dowel, if necessary.
    • Tilt the inner cage enough to remove it from its housing.
    • Rotate the race inside the cage--the part that holds the balls against the inner cage--and remove the race from the cage.
      Replace the CV Joint
      • Apply a thick coat of grease to the new CV joint race using special high temperature/high pressure grease (see Tips below).
      • Install the race inside the new cage. Then install the cage/race assembly inside the CV joint housing.
      • Tilt the cage at different angles and fit the new balls in place.
      • Slide a new CV joint rubber boot over the interconnecting shaft.
      • Install a new snap and stop ring on the interconnecting shaft.
      • Push the interconnecting shaft through the CV joint assembly to force the snap ring through the assembly.
      • Apply a thick coat of CV joint grease to all moving parts of the assembly.
      • Apply a coat of CV joint grease to the inside of the rubber boot. Then slide the boot over the CV joint assembly.
      • Install the boot straps at each end of the boot, and tighten the straps using a clamp tool or screwdriver, depending on the type of clamp.


Mar 22, 2012 | 1997 Chevrolet Cavalier

3 Answers

I need to remove my front axel on my 1989 toyota camry


Jack up car and apply e-brake. car will roll if one of the front tires leaves the ground. remove tire , spindal nut and lower ball joint bolts. remove axle from hub then use a prybar to pop it out of trans. the passenger side will have a braket holding axle to engine , remove bolts from braket or squeeze snap-ring to rmove axle from braket.

Jan 11, 2011 | 1989 Toyota Camry

1 Answer

What holds a passengers side drive shaft in on the front differential of a 2000 suzuki ventura?


The attached hub and bearing when installed keeps everything together. After removing all items from the axle outer end the inner shaft is locked in by a c ring. It simply snaps in and the same upon removing the shaft. The c ring will stay on the shaft when taking the axle shaft out

Jan 10, 2010 | 2000 Suzuki Vitara

3 Answers

My front differential is leaking!


I cannot see it, but I am guessing that you need to replace your axle seal. To do this,you have to pull your CV shaft out. Remove the tire, remove the caliper from the top of the rotor. Using a hammer on the back, remove the rotor. Take off the spindle (axle) nut, separate the axle (CV shaft) from the hub. Replace seal. It should pop right out. Good luck!

Aug 05, 2009 | GMC Sierra 1500 Cars & Trucks

Not finding what you are looking for?
2002 kawasaki VN 800 A Vulcan Logo

Related Topics:

183 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4533 Answers

yadayada
yadayada

Level 3 Expert

76630 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...