Question about 1997 Honda VTR 1000 F Firestorm

1 Answer

Clutch problem vtr1000

I just changed my chain n sprockets n now the clutch wont work i tried the solution posted but it is still not fixed plz help. Mel!

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 39 Answers

The cover that you took off to do the front sproket is where the clutch push rod gets pushed by the slave cylinder take cover off thats the only thing that could go wrong

Posted on May 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

WEN 6014: Motor is running, but chain doesn't move. Chain sprocket seems fine, cogs are only slightly worn, sprocket fits perfectly, no wear. Is there an internal clutch or connector? Motor worn out?


There is a clutch behind the metal housing where the chain sprocket at the engine end attaches to the chain . There are wear parts with springs on them that have to be changed. ChainSaw Shed Chain Saw Parts for Wen Wagner Brand Chain Saws Chains Bars... You can get parts here.

Sep 15, 2016 | Garden

1 Answer

I pull the clutch lever and it wont disengage. Before i ave done some work on it, pull out the front sprocket cover and took out the push rod (chain sprocket change), put back the cover in place than the...


Drain the oil and Pull the clutch cover off. That rod connects to the clutch push button. sounds like it fell out. Undo all the little clutch cover bolts. Carefully pull the cover off leaving all the clutch plates in a stack as some are different to others usually the first or last plate .Check the center of this plate as that is where the button usually is. Put it all back together and check clutch with cover off. You should see it move away as you pull the lever. Make sure you back off your clutch first. Hope this helps cheers

Oct 23, 2013 | 2004 Suzuki GSX-R 750

1 Answer

Blades wont enga ge


slack adjuster too tight, bar jammed into sprocket,clutch slipping, chain brake on in off position,chain binding on sprocket or bar, broke end on crank, sprocket slipping on end of crank, a clogged/pinched bar guide,etc.

Sep 02, 2013 | Garden

2 Answers

Chain turns when idling


If the oil pump gear is driven by the back of the sprocket you must make sure the the sprocket has engaged into it correctly if it has not the sprocket will bind on the back of the clutch

Sep 07, 2012 | Garden

1 Answer

Poulan pro model 4218 got caught in stump I was trying to cut down. Bar was bent. Went to box store where I bought the saw and bought "POWER CARE" 18A replacement bar and chain, brought it home and...


Try the easy solution first and post back if this does not solve the problem:

Insure your chain is on the teeth of centrifugal clutch sprocket correctly. It is easy to have it either on the inside of the sprocket or on the outside of the sprocket. If it is not on the sprocket teeth, it will not turn the chain.

Sep 29, 2010 | Poulan 18" Chain Saw Replbar (small Saws)

2 Answers

My electric chainsaw used to carve ice, chain stops while motor still spins when cutting ice


Is there some form of tensioner for the chain or do you believe it's the drive sprocket?Gas chainsaws have a bolt you can tighten which takes up the play in the chain.The drive sprocket is either on a key-way or clutch.I would remove the chain and check the drive sprocket.There must be a clutch to allow the motor to free spin until a given RPM would drive the chain.That clutch is suspect.You didn't give any information(make or model of chainsaw)that I could use to search for an answer for you.Try to work on that clutch,re-post if you need more help.

Jan 13, 2010 | Garden

1 Answer

Unit works but chain stops when pressure applyed, what oil goes resevior.


Does the motor continue to run when chain stops? Electric saws usually don't have a clutch, so I would look for badly-worn chain sprocket, or a possible sheared key in the sprocket hub, or a loose mounting nut. Remove the chain and bar, try to turn the sprocket by hand (wear good gloves). There may be some type of overload clutch built into the sprocket.

May 09, 2009 | McCulloch 10" Electric Pole / Chain Saw

1 Answer

Husqvarna 50 Chainsaw - chain wont engage with throttle


if you lost tension on chain and now it wont turn you might want to check sprocket

Nov 06, 2008 | Garden

Not finding what you are looking for?
1997 Honda VTR 1000 F Firestorm Logo

395 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4888 Answers

yadayada
yadayada

Level 3 Expert

79847 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...