Question about 2006 Bajaj Wind 125

1 Answer

Wiring diagram shorted circuit hence need an electrical diagram to trace shorted parts or wirings

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An user who is expert in 3 categories / brands.

  • Master
  • 1,727 Answers

Need model number... if this is an Asian motorcycle/scooter you are not going to like having electrical problems. I can help but you need to tell me exactly what is wrong... And no, I don't speak slang so you better know what it's called

Posted on Nov 27, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Saturn vue keeps blowing tail light fuse

You have a shorted wire, get a wiring diagram and trace down the wiring to find the short

May 02, 2018 | Saturn Cars & Trucks

1 Answer

What causes mains fuse to blow ?

A large short!. A short is a hot wire unintentionally touching ground- a metal piece of the frame. It will immediately cause sparking and blow a fuse. Also, an electric motor can have an internal short and blow the fuse for that circuit.
To find what is blowing the fuse, you have to follow every circuit that fuse protects until you find the source of the short. Look for burnt wires, like maybe too close to exhaust. Also a shorted wire can be bundled within a wiring harness, touching other wires and blowing a fuse. Since it is a main fuse, you will probably need a wiring diagram to trace all the circuits which that fuse protects. Try to isolate parts of circuits, like disconnecting the electrical connector at the ignition switch and then see if a new fuse blows. Keep working through each circuit like that until you see results. If some part or component is disconnected and the fuse doesn't blow, then you may be onto it- it could be that part you disconnected, or the wiring associated with the part.
Find a wiring diagram and see what all is part of that fuse. Good luck.

Oct 14, 2017 | Cars & Trucks

1 Answer

What causes fuses to blow while trying to start engine on 93 Jimmy

You have a dead short to ground on those circuits an blows when trying to start the vehicle because those circuits only get power from ignition switch in start or run ! Check out how to find a short circuit video on youtube . Also check out basic electrical trouble shooting , how to read a wiring diagram .Then go to free wiring diagrams . You'll need those to trace out the different circuits !

Apr 16, 2016 | Cars & Trucks

1 Answer

2006crownvictoria fuel pump relay fuse keeps blowing tried resetting relay fuse still blowing fuses why &how do i fix problem

There is a short to ground on that circuit . Go to youtube an check out videos on how to fine an automotive electrical short . Also watch videos on basic electrical trouble shooting , how to read a wiring diagram . Go free wiring diagrams . Then trace the circuit , look for bare wirers touching body ground or shorted components etc...

Mar 21, 2016 | Cars & Trucks

1 Answer

My 1994 ford thunderbird v8 eec fuse keeps blowing. Ive replaced it about 3 times everytime i try to start it the fuse blows

You have a dead short to ground on that fuse , you need a wiring diagram an electrical distribution diagram . You have to see what all is powered by that fuse , Then disconnect things , one thing at a time till the fuse doesn't blow any more . Then with a DVOM - digital volt ohm meter ,trace out that circuit an find the short . Go to for free wiring diagrams . If you don't have an automotive electrical system knowledge you can check out some basic automotive electrical trouble shooting videos on you tube .

Jan 03, 2016 | Ford Cars & Trucks

1 Answer

Blowing ctsy fuses on 1994 chev 2500

You have short on that circuit , You need to find a wiring diagram an wiring harness layout diagram an trace that circuit out till you find the short , sound easy ! Well it's not ! They sell short circuit testers that make it easy , For a few hundred dollars ! Finding The Source Of Electrical Shorts In Your Car

Aug 23, 2015 | Cars & Trucks

1 Answer

I need a wiring diagram and manual for my camper. ive got a short somewhere in my wiring.

Honestly, a wiring diagram will not help you. What you will need to do is remove all fuses, and replace them one by one until you find the circuit where the "short" exists. Once you have done that, you will need to trace the wiring (either manually or using a tone device) to determine where the short circuit exists. Most likely, a wire has become crushed or a staple or nail has been driven through a wire.

If removing all fuses from the fuse panel does not eliminate the short circuit, the problem is in the wires running from the battery to your fuse panel.

May 06, 2015 | RVs

1 Answer

My 1989 gmc c 2500 panel cluster started smoking

You have a serious short circuit in the instrument panel and if the fuse did not blow and if you didn't switch of the motor your car could have caught fire.
You need an auto electrician to fix this problem. You maybe able to trace down the short circuit by looking for burnt electrical wiring etc. but you also need a wiring diagram to trace the wiring to replace the the damages wiring and any components.

Mar 16, 2012 | 1989 GMC Sierra

1 Answer

My electricity trips out as soon as i turn my dryer on a time to work. if turned on and just on standby and not on any time it's fine, but as soon as i turn the knob to a time it all cuts out.


Either there is an internal short or the control module is shorted inside.

The control board is difficult to test. Usually you first check the board at the glance to check if any component is melting or if there is trace of damage. If timer is analog(I don't have model number), then check for shorts at the contacts. If there is nothing at a glance inspect the rest of the wiring and parts, then eventually replace the timer board if all the rest is testing good. If the machine trips off when you turn on the timer, then either the heater or the motor can be shorted. Check wiring at motor and heater. A multimeter set on impedance may help to find shorts. Most shorts that result in main breaker trip off are visible at a glance because they leave traces (also smell) of burning. Testing is done after disconnecting the appliance from power by tripping circuit breaker or unplugging power cord.

If you need parts or diagrams see this tip explaining how to find parts and diagrams for most appliances: Where do I find parts and diagrams for my appliance?



Sep 20, 2011 | Dryers

Not finding what you are looking for?
2006 Bajaj Wind 125 Logo

244 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bajaj Experts

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4974 Answers


Level 1 Expert

8 Answers

Are you a Bajaj Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides