Question about 2001 Harley Davidson FLHRCI Road King Classic

1 Answer

Remove gas tank

Motor misfires and dies at 1/4 throttle smoothes out when I accelerate past that point, happens in all gears worse when its cooler weather

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Master
  • 1,727 Answers

Does it idle correctly ??? You have an idle mixture screw that might need to be tweaked a little or you have an idle jet that is dirty. When you turn the throttle past that point you are pulling fuel through the main jet and bypassing the issue. Try to partially apply the choke and see if it runs better at your problem spot, this will help diagnose the issue...

Posted on Nov 27, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 Ford Explorer. Wrench light (powertrain) and Check Engine light is on. The codes say Throttle Motor, Throttle Position Sensor and a couple other throttle problems. While engine (REALLY ROUGH) is...


Non of what was replaced was had
anything wrong with those parts

The only issue is Class A Cylinder misfires
that spike the PCM & you loose throttle plate
position

Need to work on ignition coils & such

Sep 09, 2013 | 2006 Ford Explorer

1 Answer

1997 Plymouth Voyager 3.3 dies at idle hesitates during acceleration


It should show up with a P code as it misfires. If it doesn't, check the engine temperature sensor and O2 sensor.

Mar 01, 2017 | Cars & Trucks

1 Answer

1994 Ford escort 1.9L sputters


throttle position sensor or crank position sensor. but first have it on a fault diagnosis machine to find a fault code and go from there

Feb 27, 2012 | 1994 Ford Escort

1 Answer

I have to push the accelerator almost to the floor to get it to go in to passing gear. Motor feels weak and takes a long time to gain speed. car feels heave but the motor runs very smooth


Actually, this is normal. To 'kick down' the gear in the transmission, you should go WOT or wide open throttle.

4 cylinder motors seem to feel weaker than v-8's and are tuned to the transmission to rev higher to accomplish a certain acceleration point.

Good luck on driving.

Jul 08, 2010 | 2004 Mazda 3

2 Answers

Code p0300 and p1406


P0300 is misfire and p1406 is EGR. It sounds like you have a chunk of carbon stuck in the EGR valve. Remove the valve and clean the carbon from the valve, bottom side. Then install a screened gasket so it won't happen again.

Jun 24, 2009 | 1996 Chevrolet Blazer

1 Answer

97 srad no power under 4000 rpm in, in first gear acceleration


If you have installed the Dynojet kit's carburetor needles take them off and use the stock ones.
Dynojet's needles are for track use only and the don't work properly under 4000rpm.

Jun 15, 2009 | 1999 Suzuki GSX-R 600

1 Answer

Starts fine, but will not accelerate: Homelite UT-10798R


Do you have the H and L adjuster screws on the carb? If so, then normally I'd back out a little bit on the L (low speed side of carb) The instructions for adjusting carbs, years ago, on 2-stroke, say to back out on the L when motor will not rapidly rev up. Most 2-stroke carbs have these 2-jets. The L is for gas to pass to motor with butterfly throttle plate closed. When opening throttle plate, there is a sudden rush of air, at first, and this L adjustment is allowing enough gas to pass for motor to begin to rev. up. Then the gas will also flow through another small port H, usually a small brass tube in the venture area (smallest diameter section of carb). You adjust the H with the throttle wide open, motor revved up. Turn either in or out slightly till highest RPMS reached, motor smooth and fast, then turn H out about 1/4 turn. The idea is to run motor slightly rich for highest HP when under load (cutting). Hope this helps

Nov 18, 2008 | Garden

Not finding what you are looking for?
2001 Harley Davidson FLHRCI Road King Classic Logo

124 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...