Question about Motorcycles

1 Answer

CODE 12 2008 YAMAHA RAIDER

BIKE CAME IN WITH A NO START NO CRANK ISSUE FOUND CODE 12 REPLACED THE CRANK SENSOR / PICK UP CANT CLEAR CODES STILL NO CRANK NO START WILL RUN WITH A REMOTE STARTER WIRE FROM BATTERY TO STARTER ALSO IF JUMPING THE SOLENOID WITH REMOTE STARTER WIRE BUT NO CRANK NO START WITH START BUTTON ANY HELP WOULD BE GREAT AND THANK YOU IN ADVANCE

Posted by on

  • DAN THOMAS
    DAN THOMAS Nov 26, 2013

    YES I HAVE A NEUTRAL LIGHT I HAVE CLEARED THE CODES AND STILL HAVE NOTHING THE RELAY AND SOLENOID ARE BOTH NEW I CAN START THE BIKE USING A REMOTE STARTER BUTTON FROM THE BATTERY TO THE STARTER ALSO AT THE SOLENOID SO THE STARTER CIRCUIT IS IN GOOD ORDER WHEN I PUSH THE STARTER BUOOTN ON THE BIKE THE RELAY CLICKS AND YET I HAVE NOTHING NO CRANK NO START

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 17 Answers

Selenoid is bad....replace, or jus keep arcing it to starter, selenoid is bad

Posted on Dec 07, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 29 Answers

SOURCE: Starter dragging problem

Two things come to mind, other than an internal problem with the starter. Diconnect the battery and take the small cover off the solenoid. pull the plunger and spring out and check the 2 internal contacts and the copper washer on the plunger for a badly burned or worn condition. Rebuild kits are available for some models. If not, you can dress up the contacts and the washer. Push the plunger in by hand and see that it hits both contacts at the same time.
Another possibility is the starter clutch. Usually when these fail the starter spins without turning the engine over, but I have seen them cause the symptom you described. Replacement involves removing the starter and dissasembly of the drive end of the starter, but since you were savvy enough to take the initial steps you mentioned, I know you can handle it.

Posted on Dec 25, 2008

tellme2
  • 137 Answers

SOURCE: Yamaha xj600 doesn't start

hi m8,, i guess u have a neutral light lit up 2,, u need that to start it as well,, no light and she wont go ,, or try pulling the clutch lever in as u push the starter,, ,if none of that works,, then 1st u can do a quick experiment ,, grab a rubber or plastic handled screw driver, and cross the two terminals on the solonoid, if she turns over then the starter button needs cleaning up, or may have a break in the wire,

Posted on Dec 27, 2008

  • 2 Answers

SOURCE: My 2005 Suzuki Boulevard Will not start most of

Same problem here ... 2008 C90T ... dealer no help ... in 3rd or 4th, ignition off, force it to roll backwards until you hear the piston shift ... should start then. Told it's the rear piston stopping at or near top dead center, but also told adjust the decompression will "solve" the issue; anyway, a rolling forward-start in 4th will work, too, otherwise try rolling the bike backwards until you hear, and you will know when the piston moves and then it will start.

Posted on May 25, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1997 Chevy pick up 4.3 I though it was the coolant sensor because a code camr out


crank sensor will do the same as a cam sensor ans is the same code

Oct 21, 2015 | Cars & Trucks

1 Answer

Customer stopperd to refuel the bike and and it wont crank has error code 12 it is a 2008 yamaha raider 1900 replaced the crank sensor cleared the codes and still has a no crank issue if keep trying to...


not enough power in battery, common issue for most street bikes, to save room and weight, they put a battery on em that s well a wee bit just enough to run the machine, but in most cases simply isnt enuff, try jumper cables,, then chase starter selenoid or run stop swithch

Nov 26, 2013 | Motorcycles

2 Answers

I have a 1994 chevy s-10 pick-up. I just replaced the gas tank, sending unit and fuel pump. Still won't start Prior to doing this I tried to drive it last week. It started and ran for about 2 minutes and...


Check the distributor cap and rotor.... If they look originial or if there's any moisture inside the cap, replace both of them.
Make sure that if you do replace them that theres no moisture in the distributor before putting new parts in.

Oct 21, 2013 | Cars & Trucks

1 Answer

Car has dieing while going dwn rd. Sometimes wjll start rght back up, other times we wait sometimes hrs. I've checked the coil pack& module both pcm &ecm were checked by g&s auto and said...


Code 17 & 18 are crank/cam correlation codes. Depending on what car you have, some sensors are dual sensor, crank and cam in one. Some are set up with up to three sensors. One crank and one or two cam sensors. I you have a dual sensor, I would replace it, but check the plug first. Sometimes corrosion can mess with sensors. Just unplug it and plug it back in. This usually takes care of contact issues. Clear the light and see if that code comes up again. If you have two or more sensors, then we are talking timing belt issues. To check code 26, you will have to check for voltage on that wire. Pinout and color codes are needed to find the wire from the ECM. Again not knowing your car, voltage could be 5,8, or 12 volts. Or real close to these numbers. If you don't see any voltage from here, the ECM is bad. Quad drivers either work or don't work. 56 is an 02 heater code. This could make the car run a little rough, but not cut out. Now the injector test, if you didn't get a reading from the injector, it is bad. This will make the run real bad, Because you lost that cylinder.

Jul 13, 2013 | Cars & Trucks

2 Answers

Car died. Cranks, but wont start. Codes P0328, P0340


Yes, if the camshaft position sensor has failed, your vehicle won't start.

Jun 11, 2013 | 2004 Nissan XTerra

1 Answer

93BUICK H BODY 3.8, CODE 42, HELP!


On 3.8 engines I have seen problems with the cam and crank sensors - also the harmonic balancer and the magnet on the cam gear.
You might want to take a look at those issues too.

Aug 31, 2012 | 1993 Buick LeSabre

1 Answer

2007 road king codes p0152, S-U1016, SP - U101. Bike will crank but wont start


P0152 Rear O2 sensor high (rich)

U1016 Loss of ECM serial data - this is why the bike will not run. Fix this first.

NO code such as U101

Jul 19, 2012 | Harley Davidson FLHRCI Road King Classic...

1 Answer

I have a yamaha r1 and it's showing error code 12?


The error code 12 on your bike is a crankshaft position sensor malfunction. Just means you should replace that sensor.

Feb 24, 2010 | 2005 Yamaha YZF-R1

5 Answers

Trouble code 1345 crank sensor/camshaft sensor correlation


I had this same P1345 code on my 1998 GMC K1500 5.7 for about 2 years. Each time the code was erased, the "Service Engine Light" came right back on with the same code. I tried replacing the cam sensor, but that didn't solve it. I had the timing adjusted, it was out -13 degrees. After adjustment, the "Service Engine Light" went off, but only for a short time. Adjusting the timing is just a temporary mask on fixing the real problem and eventually you will run out of adjustment. I read about this same problem on another forum and someone recommended changing the distributor gear. So I checked the gear and a the teeth were worn. Replaced the gear ($35 part), readjusted the timing and the light has been off ever since. Apparently the gears in 96-99 are soft and wear enough to throw off the timing. This code is telling you the crank and distributor are out of sync. So before you start buying sensors and other misc. parts, try the distributor gear if you are getting a P1345 code.

Mar 03, 2009 | 1998 GMC Sierra

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

291 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76682 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...