Question about Motorcycles

1 Answer

Can anyone show a picture of which way piston goes in cylnder on kx 125

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 41 Answers

Piston always moves up and down

Posted on Nov 25, 2013

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 66 Answers

SOURCE: how much trasmission oil goes in a kx 125 2005

sae 10w40 0.74 qts.

Posted on Feb 20, 2009

  • 3567 Answers

SOURCE: 2002 kx 125 fork oil level

3.5 inches to 5 inches from the top of the fork with the cap removed.

Posted on May 03, 2009

robotek
  • 1512 Answers

SOURCE: wher can i get a cylinder and piston kit to suit

Hi
Just to confirm with you... looking for a piston kit, barrel, and topend gasket kit for your 1991 kx125?
Where in the world are you?
regards
robotek

Posted on Jul 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Which direction does piston face on 2001 kx 125 show picture


there is normally an arrow or numbers that point to the exhaust port on the top of the piston , also there are intake ports that should line up to the piston !

Nov 24, 2013 | Motorcycles

2 Answers

I have a 1987 kx 125 just put topend gasket set in with piston and rings and coolent is getting in the case bottom end anyone know why plz help me


It sounds as if you have rebuilt the engine without torqueing the head bolts. Although, it could be that the cylinder base gasket has been torn during the rebuild. Try to re-tighten the head bolts to the correct settings first. Good luck.

May 23, 2012 | 2003 kawasaki KX 125

1 Answer

I need to know how much engine oil goes in my 2003 kx 125


there is a checl bolt on the rh side it doesn't hold anyhting one and has a copper waher. sorry i tried to get the picture on here but it's to big

Jun 24, 2011 | 2003 kawasaki KX 125

1 Answer

Engine started knocking badly at high RPM. Just loan it to a friend and think he may have put straight gas in it?


Usually if straight gas was run it seizes up, but not all the time, if it didn't run long. If you take off the muffler you can look inside the cylnder, pull the starter rope untill the piston goes down and then you can view cylnder walls. This should appear smooth and shiny, any scratches and gouges would indicate straight fuel was used. If the cylnder shows these signs its an expensive fix. Good luck, hope this helps.

Dec 10, 2010 | Husqvarna 502cc Back Pack Blower HVH 350BT

1 Answer

My 2003 kx-125 will not kick over. It has a new piston but locked up on me recently. Please help me Thanks, Dustin


hopefully u put the rite size rings n piston in--du u hav proper libricant in case-what that model calls for--how is the cam chain tensioner @ correct value--du u have a shop book like clymer etc

Aug 30, 2010 | 2003 kawasaki KX 125

2 Answers

Why would clip holding gudgon pin in on piston come out and make a bit of a mess after 70 hrs use kx 85 08


Unfortunately it is never possible to find out the cause, it is not very common, but does happen. For this reason when doing work on the piston it is recommended to always use new circlips.
Even then it may be the installers fault, or a damaged clip, or the groove in the piston not machined exactly.

May 25, 2010 | 2003 kawasaki KX 125

1 Answer

2003kx 125 thew new piston does not have arrow to


first time i heard of a piston without a mark, is this an OEM, if it is after market, consult the manual, else have it replaced, same goes with OEM.

Jan 07, 2010 | 2003 kawasaki KX 125

1 Answer

Wher can i get a cylinder and piston kit to suit my 1991 kx 125 cheap as pos


Hi
Just to confirm with you... looking for a piston kit, barrel, and topend gasket kit for your 1991 kx125?
Where in the world are you?
regards
robotek

Jul 14, 2009 | 2003 kawasaki KX 125

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75807 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...