Question about Motorcycles

1 Answer

Hi there me with the tzr125 again I mannaged to open the clutch and cleaned thre plates but now the clutch won't engage from one extreme to the other Any advice thx

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Motorcycles Master
  • 1,190 Answers

Wen u had the clutch apart were there any wear on the clutch basket were the plates slotted into coz they need to be streight so the plates go back n forth smoothly !

Posted on Dec 05, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 32 Answers

SOURCE: Clutch push rod will not depress to engage

go to this http://www.cmsnl.com/yamaha-rt1-19701971_model8356/partslist/A-09.html and then click on "view big image", this will give you a diagram of the clutch etc,, the adjustment (No. 26) may need looking at, or (No.11,12,) have broken.Basically you turn 26 in (clockwise) untill you feel light resistance then back off 1/2 turn (been years since i worked on one of these!) this should give you freeplay, have you just got the bike?, and do you think it has been stripped lately(ie the clutch). PS I am not affiliated with the web site i offered above, just a handy reference for you maybe? cheers

Posted on Jul 24, 2009

  • 738 Answers

SOURCE: I just replaced the clutch

Remove cover and check if you can rotate the clutch centre without the outer moving, this would suggest the clutch centre has not seated correctly or the pushrod or opperating lever is not allowing it home all the way, i presume you measured the thickness of the clutch plates before hand

Posted on May 30, 2011

  • 409 Answers

SOURCE: how to bleed clutch kawasaki zx7 1998

Sounds more like worn dogs on your 2nd gear...bleeding clutch is the same as the brakes...make sure there is fluid in the master and bleed from the slave cyl nipple down by the front sprocket casing

Posted on May 30, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1986 Honda VT 1100 C goes into gear but won't move


Hi, Anonymous and the usual suspects are:
1. Clutch cable adjusted too tight.
2. Pressure plate center screw adjusted too tight
3. A broken clutch rod.
4. Slave cylinder piston stuck.
5. Clutch plate missing from the clutch pack.
6. Clutch plates have worn past minimum specifications.
7. Clutch plates crystallized due to incompatible oil.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
86 Shadow 1100 won move
86 VT1100 Clutch Won Engage
Honda SHADOW VT1100 Owners Workshop Manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda Shadow VT1100 Owner Manual

Mar 12, 2014 | 1986 Honda VT 1100 C

1 Answer

1978 Suzuki GS 750 E clutch won't engage


Hi, Anonymous and the usual suspects are:
1. Clutch cable adjusted too tight.
2. Pressure plate center screw adjusted too tight
3. A broken clutch rod.
4. Slave cylinder piston stuck.
5. Clutch plate missing from the clutch pack.
6. Clutch plates have worn past minimum specifications.
7. Clutch plates crystallized due to incompatible oil.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
Thread Clutch won engage
What did do wrong Clutch won engage or dis engage 07 DL1000
http://www.vanluik.eu/Suzuki%20GS750%20Service%20Manual.pdf
OEM parts for Suzuki
http://mybikemanuals.com/suzuki/suzuki-gs-owners-manuals

Dec 17, 2013 | 1978 Suzuki GS 750 E

1 Answer

Clutch not engaging


Well, it would shift easily with engine off, because the transmission input shaft is not turning. Engine running and clutch engaging good, the input shaft would again be stationary and allow smooth shifting.
What you have to determine is if the clutch disc or pressure plate is bad (a new clutch is needed), or if the pedal hydraulic system has a malfunction. When you push the pedal down, a rod from the top of pedal pushes into the clutch master cylinder bolted to the firewall under the hood. This cylinder has a reservoir filled with brake fluid. When the rod forces fluid from the clutch master down a steel line and into the clutch slave cylinder down on the transmission bell housing, the hydraulic pressure forces a plunger from the slave cylinder to extend and push the clutch fork lever a small amount, enough to force the clutch release bearing (aka throw-out bearing) against the pressure plate. This relieves pressure on the clutch disc and input shaft becomes stationary for easy shifting.

Jul 26, 2013 | 2000 Chevrolet Blazer

1 Answer

1985 Honda CB 700 SC Nighthawk hydraulic clutch hard to pull


Hi, Bconley721 and the usual suspects are:
1. Clutch cable bent, kinked, pinched, rusted or needs lubrication.
2. Hydraulic clutch hose collapsed or pinched.
3. Improper clutch adjustment.
4. Clutch plates rusted.
5. Pressure plate or springs to heavy for service.
6. Damaged clutch shell.
7. Damaged, bent, or stuck push rod assembly.
8. Faulty worm gear mechanism.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
http://katriders.com/vb/showthread.php?t=92873
How to bleed hydraulic clutch on motorcycle in an extreme case of air...
https://www.pdf-archive.com/timer.php?id=36746
http://www.partsfish.com/page/oem-parts-for-honda
Honda CB Owners Manuals

Apr 13, 2013 | 1985 Honda CB 700 SC Nighthawk

2 Answers

My clutch won't engage 1997 Honda civic


Clutch plate and pressure plate seem to be too weak to pull the car. To test the clutch plate, park the car on flat surface. Pull the hand brake up, start the car, depress the foot brake pedal, depress the clutch pedal, put the car in 1st gear, press the gas pedal and leave the clutch pedal at once, while keeping the brake pedal depressed.
Follow one of the two following statements:
1. Engine does not shut down and remain start. (Clutch plate, pressure plate and clutch bearing defective - Replace all as a set)
2. Engine shuts down. (Clutch system is OK and does not require any repair).

Apr 06, 2013 | 1997 Honda Civic

1 Answer

Clutch lever won't engage on 2005 honda rebel


Hi, Anonymous and the usual suspects are:
1. Clutch cable adjusted too tight.
2. Pressure plate center screw adjusted too tight
3. A broken clutch rod.
4. Slave cylinder piston stuck.
5. Clutch plate missing from the clutch pack.
6. Clutch plates have worn past minimum specifications.
7. Clutch plates crystallized due to incompatible oil.
For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
How to adjust motorcycle clutch cable
Clutch won engage can shift into gear
Honda rebel 250 Service Manual
https://www.partsfish.com/page/oem-parts-for-honda
http://mybikemanuals.com/honda

Sep 07, 2012 | 2005 Honda CMX 250 Rebel

1 Answer

I just replaced the clutch plates on my sons 95 KX 80...and now it acts like I've got the clutch engaged all the time and it won't let the gears engage...I've changed a lot of clutch plates and...


Remove cover and check if you can rotate the clutch centre without the outer moving, this would suggest the clutch centre has not seated correctly or the pushrod or opperating lever is not allowing it home all the way, i presume you measured the thickness of the clutch plates before hand

May 30, 2011 | kawasaki 650 Bizon Motorcycles

1 Answer

Clutch not disengaging when clutch lever is depressed.


Assuming the clutch cable is intact and adjusted properly at the handlebars, the normal things that would cause the clutch to fail to disengage are extremely dirty oil or that synthetic lubricant has been used in the gearbox instead of 10w40 motor oil. Synthetics can cause the cork on the fiber clutch plates to swell. This causes the clutch to stay engaged. Extremely dirty oil can also cause the clutch to fail to disengage. If the oil is dirty, change it then ride for 30 minutes and change it again to flush out the grit. Please rate my answer. Thanks.

Feb 16, 2010 | 2004 Yamaha YZ 250

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

46 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76848 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...