Question about 1997 kawasaki ZX-7R

Open Question

Need to view electric schematic

Won't start. has gas but recently had interlock taken off and want to see if they put wires back correctly.

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2010 merc gm shift lever stuck in park car will start steering wheel turns


You have a shift interlock problem . What kind of vehicle ? a mercury what ?
Shift Interlock System
The shift interlock system prevents shifting from PARK unless the brake pedal is depressed. The shift interlock system consists of a shift lock actuator mounted on the selector lever. If the ignition switch is in the RUN position, the shift lock actuator is disabled when the brake pedal is depressed.
If the selector lever will not move out of PARK with the key in the ON position and the brake pedal depressed, it will need to be unlocked manually.
Do the brake lights work ?
Visually inspect for obvious signs of mechanical and electrical damage; refer to the following chart:

Visual Inspection Chart Mechanical Electrical
  • Damaged shift lock actuator
  • Damaged transmission control (TC) switch
  • Damaged shift interlock switch
  • Failed fuse(s):
    • F20 (10A)
    • F22 (15A)
  • Damaged wiring harness
  • Loose or corroded connections
  • Damaged shift interlock switch
Symptom Chart Condition Possible Sources Action
  • Shift interlock system does not release/lock correctly
  • Circuitry
  • Fuse(s):
    • F20 (10A)
    • F22 (15A)
  • Brake pedal position (BPP) switch
  • Brake shift interlock actuator
  • Brake shift interlock actuator module
  • Go To Pinpoint Test A .
PINPOINT TEST A: SHIFT INTERLOCK SYSTEM DOES NOT RELEASE/LOCK CORRECTLY Test Step Result / Action to Take A1 TEST THE BRAKE LIGHTS
  • Apply brake pedal and view brake lights.
  • Do brake lights illuminate?
Yes
GO to A7 .

No
GO to A2 . A2 TEST FUSE F22 (15A)
  • Key in OFF position.
  • Check fuse: Smart Junction Box (SJB) Fuse F22 (15A).
  • Is the resistance less than 5 ohms?
Yes
GO to A4 .

No
GO to A3 . A3 TEST THE CIRCUIT FOR A SHORT TO GROUND
  • Key in OFF position.
  • Disconnect: Brake Pedal Position (BPP) Switch.
  • Measure the resistance between pin 1 and ground.
    s7n~tr~en~file=n0039468.gif~gen~ref.gif
  • Is the resistance greater than 10,000 ohms?
Yes
GO to A4 .

No
REPAIR circuit for short to ground. TEST the system for normal operation
Do

Jun 19, 2016 | 2010 Mercury Grand Marquis

1 Answer

Engine starts easy and immediately dies. Fuel supply is ok. Seems to be ignition/ interlock issue but i need some guidance.


Have you checked the fuel supply first. Its possible your jet valve may be plugged or dirt in the fuel bowl. One quick way of checking this is take the spark plug out and put a little shot of gas in the spark plug hole then reinstall the spark plug and put wire back in place and try to start engine. If it start and revs up for a few seconds till the gas is burnt up then stalls it is pretty certain its a dirty fuel jet or dirt in the fuel bowl. This quite often a real cheap fix .

Jul 30, 2015 | Garden

3 Answers

Saab 9-3 won't start. Has Spark but won't get gas.


why not bypass the fuel pump relay with a jumper wire / fuse and see if it will start that way

Sep 27, 2017 | Cars & Trucks

1 Answer

Error code 40, found problem, still wont start


you can disconnect the battery to clear the codes. If I remember correctly the code 40 is indicating an open injector circuit. You might want to check that area as well as the service manual for more detail

Nov 15, 2011 | Yamaha YZF-R6 Motorcycles

1 Answer

Dishwasher does not function. No lights in front panel. Have taken off kick plate and see no wires disconnected. Checked breakers in house. No sign that breaker is tripped.


You need to know if it is getting electric ,if it is then you have an interlock problem like a door switch not making when you close the door and if you aren't then trace it back is it the cord ,the outlet and so on. if you have electric and most of the time you do (there are shutoff switches close by for most dishwashers) the door is a tricky ****** that will drive you crazy. If the gasket is a little off or the door misaligned it won't start. It's a safety to keep the thing from leaking all over your floor, so try those things and let me know . Hint the wiring diagram is usually inside the back panel Be CAREFUL turn off electric if you pull panel

Jun 30, 2011 | KitchenAid Dishwashers

1 Answer

1994 nissan pickup - will not shift into gear from park. Transmission is working fine - but the button will not push down to put it into gear. With the cable can be pulled manually, and the car will lock...


Most likely it is a problem with the brake pedal interlock. This can be an electrical or mechanical problem. When you are in park and press the brake pedal, you should hear a faint click near the gearshift lever. If you do hear a faint click when you press the brake pedal, you have eliminated an electrical problem anyway- this would mean the interlock solenoid is not disengaging.

If the interlock solenoid is not disengaging, you will need to troubleshoot the mechanical problem. Often there is a return spring that pops off or breaks. The solenoid plunger can become stuck from either rust or one too many spilled cups of coffee.

If there is no sound at all (and it can be very faint, so you need to have the interior as quiet as possible. Key on, don't start the truck, everything that makes noise off) it can still be either mechanical or electrical. Begin troubleshooting by verifying that all your fuses are good.

That is about all the basics I can provide. Google your truck and you should be able to find a detailed service manual that will instruct you on how to disassemble the gearshift assembly and provide you with an electrical schematic of your trucks wiring. Good Luck, and Thank You for using FixYa.

Jun 08, 2011 | 1994 Nissan Pickup

1 Answer

F7 Error


This is schematic:
http://www.servicematters.com/docs/wiring/wiring_main.htm
But your correct model # is: GH5184XPS4

F7 Power to magnetron
interrupted
1. Check the door, hinge and cavity front alignment. Adjust as needed.
2. Check the operation of all interlock switches.
3. To check the over-temperature protection for the magnetron, unplug
microwave oven or disconnect power.
4. After 40 seconds, check to see whether this solves the problem.
5. If this solves the problem, check the cooling fan for proper operation or
blockage.
6. Unplug microwave oven or disconnect power.
7. Check resistance of the magnetron thermostat. It should be close to
0 ohms. If necessary, replace magnetron thermostat.
8. Check that the control cable to the 1100 watt inverter is correctly connected
to plug P2 on the display PCB. If necessary, adjust or reconnect.
9. If interlock switches operate correctly, replace 1100W inverter.
10. If problem persists, replace electronic control.
11. Plug in microwave oven or reconnect power.

Dec 06, 2008 | Whirlpool GH5184XPQ Microwave Oven

1 Answer

Dryer


I am a recently retired appliance engineer of 20 years this sounds like a door interlock problem, have you had it in bits, for some reason, it sounds like the wires have been reversed, it may be that the interlock has moved or been damaged, or has just gone faulty, check wires on the interlock are not shorting out, these can normally be sen after removing the lid, start with that and post if still having problem for reasons of safety the machine should not be left plugged in if children about work with safety, unplug when working on machine

Sep 09, 2007 | Malber TD700 Electric Dryer

2 Answers

Door Lock LED flashing


Hello, This depends on how old your machine is mine is now 7 years old so I do not want to invest in long term soltions. So I repaired my own, I bought a new interlock and replaced the old one that did not work. So I shorted out the three links that go to the interlock, the machine now shows the lock is always on and you can open the door during the wash cycle so BEWARE. Also if you have never wired a plug or fixed basic electrics DO NOT DO THIS. 1. Turn off power and unplug. (Very Important) 2. Remove lid you will need torx drivers. 3. Unscrew door interlock from the front of the machine. 4. Lift out interlock. Try replacing the interlock with spare first (about £15). 5. If new interlock does not work do the following. 6. Put Interlock back on without wires attched to it. 7. From car spares shop buy spade conectors and create a three way shorting link (insulate well). 8. Put shorting link into each of the wires that go to interlock. Safely tie up wire to a loom (do not let dangle) 9. Shut the door remove hands and try starting the machine. 10. If that works put the machine back together. And warn people that the DOOR CAN BE OPENED DURING WASH CYCLE and STARTED WITH DOOR OPEN. So check when the machine has stopped properly.

Oct 20, 2006 | Hotpoint WMA58 Front Load Washer

Not finding what you are looking for?
1997 kawasaki ZX-7R Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

bazzz7071
bazzz7071

Level 2 Expert

342 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...