Question about Bajaj CT 100 Motorcycles

1 Answer

My engines cannot turn on to power, - CT 100 Bajaj Motorcycles

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Bajaj Master
  • 39,940 Answers

Hi, Dennis and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Bank angle sensor tripped and ignition/light key switch not cycled to the "OFF" position and then back to the "ON" position.
5. Security alarm needs a reset.
6. Starter control circuit, relay, or solenoid faulty.
7. Faulty starter button.
8. Electric starter shaft pinion gear is not engaging or over-running starter clutch slipping.
For more information about your issue, please visit the websites below. Good luck and have nice a day.
Startup Troubleshooting Starting Your Scooter 1 7
Scooter won start DOWNLOAD BAJAJ CT 100 SERVICE MANUAL
http://www.marutibajaj.com/pdf/ct100.pdf
Bajaj Auto Ct 100 2015 User Manual

Posted on Dec 01, 2015

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Installed new starter. Has power. Turn key and it won't start and lose power. If I remove & reinstall battery cable the power is back but it starter still won't work


stock engine?
i did not decode that, at all.
has power? (what 12vdc power or engine power)
turn key it wont start but does it crank.??????? fast..
and lose power, what power is lost 12vdc power or engine runs but lost power?
the power is back what power? name something, specific,
like 12vdc power, starter power, engine power.
the starter wont work, i take that its silent?
or
starter spins but engine dont?
or starter clicks
or starter, is weak
or ???? try to be clear,

no engine stated.
no transmission.

if stick shift the clutch switch must work or the starter will be dead.
does that help
ever hot wire a starter, see this.
http://www.fixkick.com/nocrank.html

if engine will not crank, say that.
then say sounds. it makes if any.

Mar 15, 2015 | 1988 Suzuki Samurai

1 Answer

05 ford ranger started knocking and shut off now won't crank. What is wrong?


Started knocking and shut off ? Now will not start?
That sounds bad - check fluids - engine oil and coolant - those three symptoms can indicate overheating (either by lack of coolant or engine oil).
Did either fluid get low AND does the engine oil look contaminated - milky colored and way overful.
Not Start? Does it turn the engine and just not fire up running?
Or does the engine not turn over at all?
If the engine is siezed - you can tell by the electrical power needed to crank the engine - turn on the lights and try to crank the engine - if all you hear from the starter is a click and all the lights dim - that means a lot of power is needed like:
1. the battery doesn't have enough power - jump start to verify
2. or it requires more power to turn the engine than the battery can provide - engine siezed - try turning the engine by hand with socket/wrench to verify.
I hope your engine is not siezed - if so - hope you still have warranty coverage on the powertrain.
Please let me know what you find and if this helps?

Mar 12, 2015 | 2005 Ford Ranger

2 Answers

Lawnflite 903 will not start


starter engages? does it try to turn over? what make and engine model?

Sep 14, 2014 | Garden

1 Answer

The power steering isn't working. The reservoir was empty and I added power steering fluid and it still very hard to steer


YOU HAVE A RUPTURE PRESSURE LINE IF YOU HAVE NO POWER STEERING FLUID IN THE POWER STEERING RESERVOIR.LOCATE LEAK THEN BLEED POWER STEERING SYSTEM BY ADDING POWER STEERING TO RESERVOIR.DONT OVER FILL BY FULL COLD MARK ON POWER STEERING DIP STICK.ADD FLUID TO RESERVOIR WAIT A 2 MINUTES.CHECK FLUID LEVEL AGAIN.WHEN POWER STEERING FLUID LEVEL STOP DROPPING.START ENGINE LET IT RUN FOR 10 SECONDS.THEN TURN OFF ENGINE CHECK POWER STEERING FLUID ADD FLUID IF FLUID LEVEL DROPS. WHEN FLUID LEVEL STOP DROPPING.SAFELY RAISE SUPPORT VECHICLE FRONT WHEELS.START ENGINE.NOW TURN STEERING WHEEL GENTLY FROM STOP TO STOP MEANING LEFT TO RIGHT DONT HOLD IN POSITION.LET THE STOP TO STOP BE QUICK.CHECK POWER STEERING FLUID AFTER YOU HAVE TURN STEERING WHEEL ABOUT 7 STOP TO STOP.WHEN FLUID LEVEL STOP DROPPING YOU AT HOT MARK ON DIP STICK BLEEDING PROCESS COMPLETE.TURN OFF ENGINE LOWER VECHICLE BACK TO GROUND WAIT ABOUT 5 MINUTES CHECK YOUR FLUID LEVEL.IF FLUID LOOKS LIKE A TAN COLOR.YOUR POWER STEERING SYSTEM FULL OF AIR.TURN OFF VECHICLE LET VECHICLE SET A LONG WHILE TO AIR BUBBLES SETTLE DOWN LOOK FOR LEAKS AROUND POWER STEERING PUMP FRONT SEAL AND CHECK FOR LEAKS AROUND POWER STEERING LINES.

Dec 01, 2010 | 1999 Oldsmobile Alero

1 Answer

7.3 Liter Diesel starts hard in morning, ok if not left more than 8 hours. How to check the Glow Plugs?


Your glow plug relay is located on the top of the engine on the right side toward the front. Some models there are 2 solenoids. A large one toward the front and a smaller one right behind it. The glow plug relay is the smaller one toward the rear. The larger front one is the intkae heater relay. To test the glow plug relay turn engine to on. dont start it. both of the large terminals should have power with key on. then turn engine off. only one large terminal should have power. If when you turn engine to on you only have power on one side then go to this test. Turn engine on and test smaller wire. it should have power. If it does replace the relay. If the smaller wire does not have power you have an ignition problem or power (wiring) problem to the relay. Also note the engine needs to be cold. If temp of engine is over 130 the computer will not turn the glow plug circut on! Most of th time this is what fails and not your glow plugs.

Oct 27, 2010 | 1996 Ford F350 Crew Cab

1 Answer

It won't turn over. I put new starter,alt. cables starter relay switch battery etc


go to starter, with the test light make sure the big terminal comes from the battery has power.
then have some one start the car while you touch the smaller terminal with the test light.
if it has power while start then check the starter again
also check if the engine can turn by hand ( what I mean is use a socket and a ratchet to turn the crank bolt at crank pulley to see if the engine is turning )
if the engine turn, the big terminal has power, the small terminal has power then the starter is defected.
if engine turns, big terminal has power, small terminal has not then check the relay, the switch, the fuse and wiring again

Mar 09, 2010 | 1988 Toyota Pickup

1 Answer

Peugeot 206 Engine Power Loss


Sounds like your Mass Air Flow sensor is in need of service/ cleaning.

Jul 07, 2009 | 2005 Peugeot 405

1 Answer

92 jeep wrangler has power but wont turn over to start


The terms "turning over" and starting are often confused... Cranking (turning over) is when the starter turns the engine, regardless of the end result. Starting is when the engine actually runs (even if for a moment).
If your problem is that the engine is turning when the starter is engaged, but not starting, then you have either a fuel or spark fault.
If the engine is not turning, check that the battery has a full charge, and holds adequate power when loaded, that proper voltage is reaching the starter and there is a good engine ground. Power should also be present at the small trigger wire on the starter when ign key is turned to start position.After checking these things you can begin to make a decision on what needs attention and proceed from there.

Feb 28, 2009 | 1992 Jeep Wrangler

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

38 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bajaj Experts

sachin sharma
sachin sharma

Level 2 Expert

171 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Joseph Gallucci

Level 2 Expert

120 Answers

Are you a Bajaj Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...