Question about Harley Davidson Motorcycles
We are trying to fix a missing in the Ultra Glide. The bike gave us the code: PSSPt b (6?) Where can I find an electrical diagnostic manual for this bike? The missing is not constant.
Posted by Anonymous on
Hi Anonymous, PSSPT is not a code it is a menu in which to choose a particular area of the electrical system that the ICM/ECM has generated a trouble code in. For more information on how to retrieve these codes please visit the website below and good luck:
Harley Diagnostic Codes 04 to Present
Posted on May 17, 2015
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Does the sidecar harness have a square 4 pin plug? If it does it more than likely connects to the auxillary plug under the seat.
Posted on May 20, 2009
open up the ignition cover plate and check the backing plate. it may have come loose and threw the bike out of time.
make sure your plug wires are plugged on tight and the coil wires are secure.
It is most definitely a timing problem.
Posted on Jun 06, 2009
Not too hard - Undo the two bolts on the caliper and then seperate the caliper and pull the old ones out. Insert the new ones and put the bolts back in to hold the caliper back together and then install them back on the bike with the two retaining bolts. Use a bit of lock tight (Blue) on the threads. Warning do not let anyone apply pressure on the brakes while you have them off the bike or you will have a mess and/or a problem.
Posted on Jun 21, 2009
1) Remove hard bags.
2) Use a marker to mark a position of the belt tension cams on the axel. This will help you put the proper amount of tension on the drive belt when you put it all back together. The left cam is welded to the left side of the axel. The cams are used to tighten or loosen the belt tension. You will see what I'm talking about when you get there and look at it.
3) Remove the two bolts from the rear of the left side bag support. Then loosen the front bolt of the bag support. (Remove the left fusebox cover to access the front support bolt.) Lower the bag support. This is necessary to slide the rear axel out.
4) Remove the two banjo bolts from the rear brake bracket and slide off from the rotor. Support brake with something so you don't damage the brake line.
5) Look carefully at the spacers on the axel and note, along with the order.
6) Loosen the cone nut of the axel on the right side of the bike, but don't remove.
7) Use a bike jack to raise the bike so that the rear wheel is barely touching the ground. Just enough that you can turn the rear wheel and feel the treads rubbing the ground.
8) Remove the cone nut from the right side, along with the right alignment cam washer
9) Genlty tap the end of the axel from the right side of the bike until it slides out from the wheel hub.
10) Pull the axel from the left side, take note of IDS washer and spacer order and position.
11) Slowly jack up the bike until you can pull off the belt pulley...that also contains the IDS (Isolated Drive Sprocket) NOTE; Check that damned IDS bearing in the drive pulley. I have gone through 4 of those crappy bearings...usually every 10k. If the seal is broken on the IDS bearing, get it replaced. This is the wicked gremlin of the 08 FLHX. The rear IDS pulley should just pull away from the hub at this point.
12) Jack the bike up until you can roll the tire, or get it out from underneath the bike. Did I tell you to strap the bike so it doesn't fall over? Just in case ya'know.
It all goes on in the reverse order. I never mount the tire on the rim...I have someone else to that and the balancing. Make sure none of the rubber isolators in the drive pulley have fallen out. Once you have the axel back in, tighten the cone nut enough so that you can tighten the drive belt by turning the cams from the left side of the axel. Use the paint marks you put on the right side of the axel cam to get the drive belt tension where it was at the time you started this whole process. Tighten hand tight, then loosen one full turn, then tighten the cone nut on the right side to torque specs. (Damn, I can't remember what that was. I think 90 - 110 foot pounds but I can't say that with certainty. I think the brake bolts are 35 to 45 foot pounds.)
Hope the helps. You can get cheap PDF shop manuals online if you look hard enough. The best investment I have made was a Harley Shop Manual for the bike...but they ain't cheap.
Posted on Feb 22, 2011
Tips for a great answer:
Sep 29, 2012 | 2008 Harley Davidson FLHTCU Ultra Classic...
Aug 01, 2012 | 2008 Harley Davidson FLHTCU Ultra Classic...
Jul 16, 2012 | 2008 Harley Davidson FLHTCU Ultra Classic...
Oct 13, 2011 | 2008 Harley Davidson FLHTCU Ultra Classic...
May 17, 2011 | 2010 Harley Davidson FLHTCUTG Tri Glide...
Sep 29, 2010 | Harley Davidson FLHTCUI Electra Glide...
Mar 19, 2010 | 2005 Harley Davidson FLHTCUI Electra Glide...
122 people viewed this question
Usually answered in minutes!