Question about 2006 Harley Davidson FLHX Street Glide

1 Answer

06 street glide no power gauges and lights flickering on/off when igntition is on

When the ignition is in the locked position, almost sounds like static noise coming through the speakers. When I attempt to turn the bike on, the gauges and lights on the dash begin to flicker on/off and I can't even start the bike. Brand new battery but same problem. Battery is fully charged.

Posted by Anonymous on

  • mike_wade728 Dec 10, 2013

    Hi Guest, I want to help you with your problem, but I need more information from you. Can you please add details in the comment box? Are you sure the battery is connected properly red to Positive side of battery and all cables are tightened properly. Do you have an alarm

×

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Harley Davidson Master
  • 40,632 Answers

Hi Anonymous, please visit the website below and good luck:
HarleyTechTalk

Posted on May 14, 2015

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 18 Answers

SOURCE: I have a 2004 Harley Wide Glide with electronic

That is very interesting. I don't have a real solution, but if I were you I would try grounding the frame to a separate ground source. I don't know why, but I'm thinking you charged the bikes grounding source so now it doesn't appear to be a ground at all anymore. Not sure how, but the frame, engine, etc may have a huge static charge lingering on it.

Posted on Apr 07, 2010

wd4ity
  • 4565 Answers

SOURCE: bike won't start, new Harley

I'm not too familiar with the later model bikes but if I were getting a clicking noise under the seat and the bike was not starting, I'd investigate the source of the noise. It's possible that it is a starter relay that engages the solenoid that is an integral part of the starter. Look at the starter from the right hand side of your bike. You'll see a single small wire that connects to the end of the starter just above the end plate of the solenoid. Disconnect this wire and connect a test light or volt meter to the wire. Turn on your ignition switch and press the start button. You should hear the click under the seat and see voltage at the end of that wire. If not, replace the relay, a plastic cube about an inch in dimension.

Good Luck
Steve

Posted on Jul 02, 2011

  • 411 Answers

SOURCE: My 06 street glide doesn't seem to be charging

Voltage regulator is going/gone bad would be my first guess. Other possibilities include loose or corroded connection(s), sulfated battery, or failing stator (not likely).

Since electronic parts usually can't be returned, it might be worth it just to have a shop check it and give you an estimate. Even if you have to pay a diagnostic fee, if it's something as simple as a regulator, you can do the repair yourself and save some bucks.

Posted on Jul 05, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Ignition locked static noise through speakers, dash gauges and lights flickering and no power


Several things 1. was the bat. installed properly ie; cables and wires?
2.The ignition switch may be defective.
3.Last there could be a short.

Nov 19, 2013 | 2006 Harley Davidson FLHX Street Glide

1 Answer

Street glide won't start no power with ignition turned on


Hi Anonymous, try checking around the fairing bracket for tight or worn wiring harness. Good luck

Nov 19, 2013 | 2006 Harley Davidson FLHX Street Glide

1 Answer

Street glide has no power in on position


Hi Anonymous, 1992 and later touring models, fuel pump fuses and relays will be behind the right side panel, everything else will be behind the left side panel to access fuses pull back on the front two locking tabs and slide the cover up. Good luck.

Apr 09, 2013 | 2008 Harley Davidson FLHX Street Glide

1 Answer

06 street glide no dash lights


Hi Anonymous, and the usual suspects are:
1.Ignition/Light Key Switch not in IGNITION position.
2.Engine Stop switch in the OFF position.
3.Discharged battery, loose or corroded connections check negative cable at both ends. (solenoid chatters).
4. Bank Angle Sensor tripped and Ignition/Light Key Switch not cycled to Off and then back to on.
5. Starter control circuit, relay or solenoid faulty.
6. Electric starter shaft pinion gear not engaging or over-running clutch slipping.
7. Security alarm not disarming
For a prime suspect please visit website below and good Luck.
Harley Diagnostic Codes 04 to Present
Set Change Override Transport Harley Security Alarm PIN Code No Key Fob...

Apr 09, 2013 | 2008 Harley Davidson FLHX Street Glide

1 Answer

Where are the fuses located on an 06 street glide


Hi Jerry, 1992 and later touring models, fuel pump fuses and relays will be behind the right side panel, everything else will be behind the left side panel to access fuses pull back on the front two locking tabs and slide the cover up. Good luck.

Oct 01, 2012 | 2006 Harley Davidson FLHX Street Glide

1 Answer

2004 Dyna Super glide Fuel Gauge not working


Hi Anonymous, you could have a faulty sending unit or guage, there could be a problem with your wiring. On models with the fuel gauge posing as a left hand fuel cap the gauge is a press fit do not try to unscrew it, simply ample force lift up in a rocking motion to remove gauge. Disconnect wires to the gauge and with a set of positive and negative jumpers from the battery connect the positive jumper and flash the negative, gauge should peg full, if not replace gauge. With a test light check for power to the sending unit, then remove the sending unit and manually operate the float arm slowly with the correct wiring hooked up to the fuel gauge and sending unit and the ignition on, the gauge should respond accordingly if not replace the float arm assembly. For a free wiring diagram please visit the website below and good luck.
Harley Davidson Wiring Diagrams and Schematics

Aug 03, 2012 | 2008 Harley Davidson FLHX Street Glide

1 Answer

My 06 street glide doesn't seem to be charging the battery all the time my gauge for volts jumps around from 12 to16 then my battery light and engine light come on


Voltage regulator is going/gone bad would be my first guess. Other possibilities include loose or corroded connection(s), sulfated battery, or failing stator (not likely).

Since electronic parts usually can't be returned, it might be worth it just to have a shop check it and give you an estimate. Even if you have to pay a diagnostic fee, if it's something as simple as a regulator, you can do the repair yourself and save some bucks.

Jul 05, 2011 | 2007 Harley Davidson FLHX Street Glide

1 Answer

Fuel gauge on 2002 street glide work then doesn't , it kicks back and forth what could be the problem.


Hi Eric_prior, you could have a faulty sending unit or guage, there could be a problem with your wiring. On models with the fuel gauge posing as a left hand fuel cap the gauge is a press fit do not try to unscrew it, simply ample force lift up in a rocking motion to remove gauge. Disconnect wires to the gauge and with a set of positive and negative jumpers from the battery connect the positive jumper and flash the negative, gauge should peg full, if not replace gauge. With a test light check for power to the sending unit, then remove the sending unit and manually operate the float arm slowly with the correct wiring hooked up to the fuel gauge and sending unit and the ignition on, the gauge should respond accordingly if not replace the float arm assembly. For a free wiring diagram please visit the website below and good luck. Harley Davidson Wiring Diagrams and Schematics

Sep 10, 2010 | 2008 Harley Davidson FLHX Street Glide

1 Answer

Im adding lights to my 2006 street glide.


You turn the ignition knob to LOCK position, and then you feel under the knob on the left for a switch. Push that up with your finger and at the same time, turn the ignition KEY (not the knob) counter clockwise for about 1/8 turn. You will feel a click and the knob will pull right out. After that, unscrew the collar nut on the threaded section and two metal pieces and a plastic spacer pull off. The fairing cap (the plastic cover) is attached by two bolts, on the outer sides. The wiring loom will disconnect when you unplug the connector.

Mar 10, 2009 | 2008 Harley Davidson FLHX Street Glide

Not finding what you are looking for?
2006 Harley Davidson FLHX Street Glide Logo

159 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...