Question about Moto Guzzi Motorcycles

Open Question

Hydraulic clutch replace - Moto Guzzi Motorcycles

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Seem to be going slow even when accelerating on my c max 1600 diesel


hydraulic clutch---replace the faulty clutch master cylinder
( compensating port blocked keeping the clutch partially disengaged and slipping)
cable clutch ,---replace the cable
( same indications for hydraulic clutch)

Nov 13, 2017 | Cars & Trucks

1 Answer

I have a 1998 Dodge Dakota 3.9 with a 5 speed. I am having difficulties with the clutch and am trying to figure out if it is the clutch needing replaced or if it is the hydraulics.


Bad hydraulics (leaking/spongy) and worn out clutch have opposite symptoms. If the clutch does NOT ENGAGE - get the vehicle moving - you probably need to replace the clutch and/or pressure plate.
If the clutch does NOT DISENGAGE - you can't get the transmission into gear, or there is difficulty or grinding when trying to shift between gears - your hydraulic system is not moving the clutch release arm far enough to disengage the clutch.

Jun 09, 2017 | 1998 Dodge Dakota

2 Answers

How do I adjust the hydraulic clutch on a 1996 Chevy s-10?


The beauty of hydraulic clutches is there is no adjustment.
If your clutch is slipping it is all done.
if you are having issues with clutch disenguagement , then there is a possiblity of other componants needing attention...

Mar 23, 2013 | Vehicle Parts & Accessories

1 Answer

Transmission issues


Typical Clutch Problem. Check to see if Clutch Linkage is Hydraulic or Mechanical. If Hydraulic then replace Clutch Slave Cylinder First.Bleed out air from Hydraulic line. if this doesn't fix it and or it has a Mechanical Clutch Linkage then Replace Clutch itself don't forget to get a new throw ou bearing and pack it with heavy duty grease otherwise in 20,000 miles you'll be doing it again. Thanks Keith

May 15, 2012 | 2004 Pontiac Sunfire

1 Answer

I have a 2007 VW Touran, recently serviced. After a motorway run using the cruise control I often find the clutch feels as if it had lost all hydraulic pressure and I have to pump the pedal to get the...


It might be the brake & clutch fluid wrong because it is too old inside. First time change the brake & clutch fluid. If the problem persists then replace both clutch master hydraulic cylinder and clutch receiver hydraulic cylinder. Bleed also correctly the clutch hydraulic line!

Sep 06, 2010 | 2009 Volkswagen Routan

1 Answer

My clutch is sitting on my floor board


This is caused by a failed clutch slave or master hydraulic clutch release cylinder has, it is best if these are replaced as a pair. here are the parts u need.
BRUTE POWER / PERFECTION CLUTCH Part # 39836 Hydraulic Clutch Master cylinder
BRUTE POWER / PERFECTION CLUTCH Part # 3788 Hydraulic Clutch Slave Cylinder

Jul 30, 2010 | 1993 Honda Prelude

1 Answer

Hi i have a peugeot 406 2.0 hdi 1999, when i get in the car the clutch pedal is on the floor and i have to pump the pedal for a couple of minutes, then it is ok to drive. any ideas what is wrong with it?


The clutch acting system is hydraulical, (clutch hydraulic system).
Your clutch pedal master cylinder is weak, and needs to be replaced or repaired by gasket kit replacement. Also the clutch slave cylinder can be used, and needs to be repaired (by gasket kit replacement), or replaced. The clutch system must be bled after carrying out work on the hydraulic clutch mechanism.

Dec 09, 2009 | 2006 Peugeot 504

1 Answer

1st, 2nd, 3rd gears difficult to select and reverse grinds in


You are in the wrong section of FixYa, but I can help you.
The reason why you are having trouble changing gears is your clutch is not disengaging properly from the engine when you press the clutch peddle.
If the clutch is a cable type control, then the clutch cable and clutch lever may need adjusting to disengage the gearbox from the engine so you can change gears without crunching the gears.
If the clutch is hydraulic type, you could have air in the system or you have leaky hydraulic seals, both of which will prevent the clutch from disengaging from the engine properly. Check the clutch master cylinder and the clutch slave cylinder for leaks. If there are leaks you need to replace the seals and if the master and slave cylinders are badly scored then they need to be replaced as well.
If there are no hydraulic leaks then bleed the hydraulic line to remove the air in the hydraulic system, you may also need to adjust the push rod from the slave cylinder to adjust the clutch lever arm so when the clutch peddle is depressed the clutch fully disengages the engine.

Oct 24, 2009 | Enlight Combo (5601908) (Beige) (5601908)...

2 Answers

My clutch is slipping on my 1993 toyota truck. Are there adjustments I can make myself. I am fairly handy, but not a car repair expert.


Sorry, there are no adjustments on your vehicle., The clutch is activated via hydraulic pressure. The master and slave cylinders are "self-adjusting". If the clutch is slipping, you are going to need to pull the trans and replace the clutch assembly. Changing the hydraulics will not help a slipping clutch at all.

Thanks for choosing FixYa for advice!

Mar 05, 2009 | 1993 Toyota Pickup

2 Answers

Trying to figure out how to adjust the clutch on a 2005 Toyota Corolla style s


You car does not have an "adjustable" clutch. The Corolla uses a hydraulic clutch. The action of the hydraulics eliminates the need for adjustements. If the clutch is slipping, you may need to replace the clutch.

Jan 15, 2009 | 2005 Toyota Corolla

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

14 people viewed this question

Ask a Question

Usually answered in minutes!

Top Moto Guzzi Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

john h

Level 3 Expert

12650 Answers

Are you a Moto Guzzi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...