Question about 2011 Honda CB Unicorn

Open Question

Honda unicorn mono shock adjustment

What is the standard setting of honda unicorn mono shock absorber, and how to adjust the settings can i do it with a screw driver

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 2336 Answers

SOURCE: Honda cbr 600f2 throttle adjuster?

Sounds like you were adjusting the idle mix screw on the carburetor. I think www.bikebandit.com has OEM parts, with diagrams. Also, there are many forums for different motorcycles and their owners on the internet, I would try a Google search for the right forum for your bike. Good Luck!

Posted on Nov 10, 2008

  • 8 Answers

SOURCE: What are the stock suspension settings for a 2003 Honda CR 250 R?

set your compression out 10 or 11 your rebound 9 or 10 and your fork oil height to roughtly 380cc.since its in 03 u should drain the fork oil out, u have to unscrew the top cap of the fork while its in the triple clamps( because its easier this way), loosen then take the fork out of the clamps, unscrew the top caps and pull the fork tube down and turn the fork upside down to drain the oil out then hang the forks up upside down for about 15 minutes then add the new oil right in the fork tube were you'll see a spring, just add the oil in there and you'll be fine and u should replace it with a good medium weight oil

Posted on Feb 04, 2009

  • 28 Answers

SOURCE: 1997 Honda Magna VF45c 750 clutch adjustment

Did you do an oil change recently? Sometimes a motor cycles clutch shares the oil with the engine and a different kind of oil then the bike requires will cause the clutch to slip. This happens alot especially if someone switches to some types of synthetic oil when the bike had regular oil before the oil change.

Posted on Jun 24, 2009

  • 3 Answers

SOURCE: Where is the idle screw, air/fuel adjustment screw on a VT750Cd

It just need to be perfect keep trying different air flows

Posted on Aug 18, 2009

nedkelly900
  • 345 Answers

SOURCE: honda xr 125 to set tappet clearances and adjust

timing chain should be auto adjust. set valve clearence to inlet 4 thou, exhaust 6 thou

Posted on May 20, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How to adjust unicorn monosuspension?


Move it to counter clock wise as it mentioned on sticker << HARD--SOFT>> depending on ur weight <<Left makes firmRight>> makes soft

Sep 26, 2012 | 2011 Honda CB Unicorn

1 Answer

How to lower honda wave 100


simple, buy small shock absorber(rear) and in front adjust the shock absorber. then buy small tires..

Jul 03, 2012 | 2005 Honda NF 100 Wave

1 Answer

My honda CB unicorn gives mileage of 38kmpl only . just on eyear old bike . any solution ?


Change the engine oil to the recomended 20/40W, oil the chain drive adjust the tension of the chain.
hope this will solve the problem

May 09, 2012 | 2011 Honda CB Unicorn

1 Answer

Torque setting 1999 300 ktm head &side cover


Thank you for contacting FixYa with your inquiry. I have been going over some of the inquiries that have been archieved and trying to provide solutions for those that didn't get answered. Hope this information helps.


KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nuts on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs

Oct 29, 2011 | Motorcycles

1 Answer

Torque setting for centre nut for clutch housing


Thank you for contacting FixYa with your inquiry. I have been going
over some of the older help requests that have been archieved and
trying to provide solutions for those that didn't get answered. Hope
this information helps.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nuts on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs

Oct 29, 2011 | Motorcycles

1 Answer

If Seat adjustment is possible in 2011cbunicorn


Your bike has a mono shock. It does have adjustments but it is for ride stiffness not necessarily ride height. But adjusting the rear shock will lower and or raise the seat a small amount. But at the lowest setting the seat height is still 792mm or 31.2 inchs. You may find a shorter shock but it would have to be from a parts search to match.

Sep 18, 2011 | 2011 Honda CB Unicorn

1 Answer

What is the axle torque settings on the front an rear axle bolts on a 2007 ktm 250 xc?


Thank you for contacting FixYa with your inquiry.
I have compiled a list of all the useful KTM torque setting that apply to your bike.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber botton bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nutes on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs
Let us know if we can provide further assistance.
Best regards,
TF

Jul 05, 2011 | KTM 250 XC Motorcycles

1 Answer

What are the torque settings?


Thanks for contacting FixYa. I was reviewing some of the older un-answered questions trying to ensure your issue has been resolved.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber botton bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nutes on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs

TF

Mar 11, 2011 | KTM 530 EXC-R Motorcycles

1 Answer

How do i adjust the hear shocks for pillian weight?


This is directly from the 2008 VRSC Service Manual:

Make sure both shocks have the same preload.

The average weight solo rider might use the extended spring
preload position (adjustment setting 1 or 2).

1. Place the shock absorber adjustment tool around the lower
collar of the shock absorber.

2. Turn the collar clockwise (toward higher numbers) to
increase the preload or pressure.

Use the adjustment setting numbers as a reference for equal
adjustment of shock absorbers on both the right and left side
of the motorcycle. A heavy solo rider might require additional
preload or pressure (adjustment setting 3).

Adding a passenger may require maximum preload (adjustment
setting 5).

Turn the collar counterclockwise to decrease the preload or
pressure.

Mar 06, 2011 | 2008 Harley Davidson VRSCDX Night Rod...

1 Answer

2009 ktm 125sx torque settings for head and cylinder


Thank you for contacting FixYa with your inquiry. I have been going
over some of the older help requests that have been archieved and
trying to provide solutions for those that didn't get answered. Hope
this information helps.

KTM Torque settings


  1. Collar screw, front wheel spindle Front axle nut 40Nm 30ft lbs
  2. Brake Caliper front Brake Caliper front Loctite 243 2 19ft lbs
  3. Brake Disk, front Brake disk front Loctite 243 1 11ft lbs
  4. Brake Disk, rear Brake disk rear Loctite 243 1 11ft lbs
  5. Clamping screws, upper fork bridge Top triple clamp 20Nm 15ft lbs
  6. Clamping screws, lower fork bridge Bottom triple clamp 15Nm 11ft lbs
  7. Clamping screws, fork stubs Front axle pinch bolts 10Nm 7ft lbs
  8. Collar nut, rear wheel spindle Rear axle nut 80Nm 59ft lbs
  9. Hex nut swingarm bolt Swingarm nut 100Nm 74ft lbs
  10. Hex collar screw handlebar clamp Upper handlebar clamps 20Nm 15ft lbs
  11. Allen head screw handlebar support Lower handlebar clamps Loctite 243 4 30ft lbs
  12. Shock absorber top Shock absorber top bolt 60Nm 44ft lbs
  13. Shock absorber bottom Shock absorber bottom bolt 60Nm 44ft lbs
  14. Sprocket screws Rear sprocket bolts Loctite 243 3 25ft lbs
  15. Ball joint for push rod Rear brake pedal pivot Loctite 243 1 7ft lbs
  16. Engine mounting bolts Engine mounting bolts 45Nm 33ft lbs
  17. Engine brace Engine brace 33Nm 24ft lbs
  18. Screw adjusting ring spring preload Shock preload collar bolt 8Nm 6ft lbs
  19. Spoke nipple Spokes 5Nm 4ft lbs
  20. Other Screws on chassis M6 10Nm 7ft lbs
  21. M8 25Nm 19ft lbs
  22. M10 45Nm 33ft lbs
  23. Other collar nuts on chassis M6 15Nm 11ft lbs
  24. M8 30Nm 22ft lbs
  25. M10 50Nm 37ft lbs
  26. Front Sprocket 44ft lbs

TF

Nov 05, 2010 | 2008 KTM 125 SX

Not finding what you are looking for?
2011 Honda CB Unicorn Logo

Related Topics:

300 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75005 Answers

Gino Cussen
Gino Cussen

Level 2 Expert

216 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...