Question about Motorcycles

Open Question

Set timing valve - Motorcycles

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I set the timing on an unidentified motorcycle?

Dan's Motorcycle " Ignition Timing "
But set the ignition timing? NO WAY... they are scared stiff of it. Others figure they can throw in a new set of points, set the gap with a matchbook cover and drive ...

Dan's Motorcycle Valve (Cam) Timing
How to time the Valves on your Motorcycle Engine. ... Every time we assemble a four stroke engine we have to set the valve timing. It's quite simple but very ...

Dynamic motorcycle ignition timing - YouTube

? 2:21
Mar 18, 2014 - Uploaded by A Motorcycle Nut
Motorcycle ignition timing. Works for all types of bikes.. Set your ignition timing for best performance. Get ...

Checking Your Timing - Angelfire
When I first started riding motorcycles, more than a few of my friends were ... is controllable by adjustment of the spark advance - setting your ignition timing.

Dec 11, 2015 | Motorcycles

1 Answer

What is codes p1111 and po447

the valve timing solenoid is what advances /retards the valve timing according to the requirement pre-set in the CPU program. If this solenoid is malfunctioning then the valve timing will be out and the cam shaft position sensor becomes unbalanced with the CPU setting and raises the fault code

The vent valve solenoid will produce problems with fuel flow and running and filling of the tank. I suggest that you have both checked and repaired by an accredited specialist shop that is conversant with you car.

Sep 11, 2014 | Cars & Trucks

1 Answer

How do I set the timing

Are you trying to set the ignition or valve timing ? The ignition timing is factory set and changes with engine rpm - you can set the air gap between the flywheel and the ignition unit which should be around 0.25mm (0.010") Excessive air gap will retard the ignition timing. Unless you\'ve had the engine apart, the valve timing won\'t need re-setting. The valve clearances will need setting from time time and the clearance between valve and rocker is 0.1mm and is adjusted with both valves closed and piston at the top of it\'s stroke - you should replace the gasket and copper washer at the same time.

Apr 04, 2014 | Stihl HT101 Pole pruner

1 Answer

How do I set the valve timing on my 2007 Astra 1.3 cdti when there is no timing hole on the bell housing

If therewere a hole to view as on other cars you would be setting "Ignition " timing Valve timing is done at the gears one on the crank & one on the cam shaft ,if so there is mark on each gear ,You should rfer to specific specs. in a book for that model & year.. You have to open the case cover for that. Are you refering to setting the "valve lash" ? If so you need to refer to "valve clearence or valve lash" specifications chart, If adjustable. Either way always check a manual for specific needs.
Mr. Red

Dec 16, 2013 | 1994 - 2001 Lexus ES300 Engine Timing Belt...

1 Answer


the piston has to be on tdc
the valves have to be in the valve rock position
that is the exhaust is just starting to close at the same time as the inlet is just starting to open
the number of links should now be at the timing marks or the timing marks should line up when the crank is turned one full revolution

Apr 16, 2017 | Cars & Trucks

1 Answer

15hp briggs

the only timing is the key on the flywheel to crankshaft i set the valves to .006 turn the engine till one of the rocker arms opens a valve then set the other one then do the same to the other valve those engines are known for valve seats falling out let me know if that's the case i can guide you to that repair

Apr 02, 2012 | Briggs & Stratton Garden

1 Answer

How do i set cam position and timing on an old yamaha xt 500

You didn't say WHY the cam / valve timing needs to be reset. For some reason I get the feeling someone told you that resetting was needed and so you are asking how. Obviously, you may have installed new pistons and that is why the resetting is needed. In either event, when the cam timing is set the valve timing is also set. Other than adjusting valve lash, setting the cam sets the valve timing. Below is a web site where you can do a free download of a factory service manual. The process is not hard but having a manual will be more help and faster help than I can give online.

May 25, 2010 | 1997 Yamaha XT 600 E

1 Answer

I just rebuilt the top end on my daughters 90cc baja atv put it together set the timing and it cranks up and you can ride it for a little bit and it will start spitting and spurtting and die and then it...

Sounds like the valves are not set correctly. It is likely the intake valve is set too tight. Set the clearance at 5 to 6 thousandths. The exhaust should set at 8 to 10 thousandths. Check the timing with a timing light if you already haven't done it. If the valve clearance and ignition timing look okay, recheck the cam gear timing.

Feb 23, 2010 | 1985 Honda CX 500 A

1 Answer

1995 acura how do u set the vals and timming

First you will need a service manual or information for this vehicle for the valve lash setting. The procedure is usually removing the valve cover( You will need a new valve cover gasket) putting the # 1 cylinder on top dead center and using wrench, screw driver or allen key,and a feeler gauge. You will need to follow the firing order when adjusting the valves. You will need a timing light to set the timing and also the timing spec. This usually involves warming engine to normal operating temp. clean harmonic balancer and mark the timing mark with some white paint loosen the the distributor hold down bolt hook up timing light and turn distributor until the timing mark on the balancer lines up with the timing mark on the timing cover then tighten the holding bolt back down. Also the timing advance has to be disabled when setting the timing and enabled when you are done. The valves should be set first then set the timing. A Haynes manual available at your local auto parts store should contain pictures and information to help you do this.

Nov 21, 2009 | 1998 Acura TL

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers


Level 3 Expert

76846 Answers


Level 3 Expert

102366 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides