Question about 2006 Suzuki GSX 750 F (Katana)

Open Question

Were does the hose from the sending unit go to

Posted by Anonymous on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change fuel pump 1999 Saturn sl1


You need to drop your gas tank, first un clamp filler hose fro underneath, and vent hose. Undo the two gas tank straps and wiggle tank down around the exhaust system. Once on the ground you will see a small ring around the hoses going into the sending unit, being very careful to not get dirt in the tank. Sending unit should pop out . The fuel pump is bolted onto the sending unit. You un plug the 2 wires going to it and the bolts holding it on, and replace the opposite way good luck

Oct 05, 2014 | 1999 Saturn SL

1 Answer

I changed my fuel pump on my 93 fleet wood and it still will start but cuts off at about ten min of driving should I get a factory cadilliac fuelpump


NOTE! WHILE THIS IS NOT A HARD REPAIR, YOU ARE DEALING WITH GASOLINE AND GAS VAPOURS. tAKE THE NECESSARY PRECAUTIONS.
Take out the back seat (there are 2 pull-tabs to release it and it will lift up) and you will see 2 square plates that are screwed down. Remove the one on the passenger's side and you will see the the top of the gas tank and the sending unit (the sending unit contains the fuel pump).
Remove the electrical connector on the sending unit, and then start the car. It should die immediatly. Try starting the car several time to relieve the fuel pressure.
Next, remove the negative battery cable for safety. Then remove the 2 hoses going to the sending unit. One is held on by a hose clamp while the other is a threaded fitting. I REMOVED THE RUBBER HOSE FIRST AND ALLOWED THE GAS TO LEAK INTO A CONTAINER UNDER THE FUEL TANK.
AFTER TRYING TO UNSCREW THE METAL HOSE COUPLING, I REALIZED THAT THE RUBBER HOSE CONNECTED TO THE THEREADED FITTING WAS TWISTING INTO A KNOT. ( THE FITTING ON THE SENDING UNIT DOES NOT TURN_YOU CAN RUIN THE SENDING UNIT BY TRYING TO TURN THE FITTING ATTACHED TO THE SENDING UNIT. )
I HAD TO JACK THE VEHICLE UP, PLACE JACK STANDS UNDER THE REAR WHEELS, AND UNSCREW THE OTHER END OF THE THEREADED FITTING FROM THE SENDING UNIT WHERE IT CONNECTS TO THE FUEL LINE UNDERNEATH THE VEHICLE. YOU WILL HAVE TO TURN THE FUEL LINE FITTING TO DISCONNECT IT FROM THE LINE THAT ATTACHES TO THE SENDING UNIT. AT THIS POINT, YOU WILL BE ABLE TO UNSCREW THE THEREADED FITTING THAT GOES TO THE SENDING UNIT. IT IS SAFER TO UNDO BOTH ENDS OF THE THREADED FITTINGS AND REMOVE THE HOSE BEFORE YOU ATTEMPT TO REMOVE THE SENDING UNIT/FUEL PUMP ASSEMBLY.
Then remove the bolts on the sending unit and remove it from the gas tank.
Replace the pump in the sending unit and then put everything back together.

Apr 23, 2014 | Cars & Trucks

1 Answer

Temperature sending unit


there are 2 hoses that connects the radiator to your engine. sensor is attached in one of these hoses

Jun 21, 2013 | Pontiac G6 Cars & Trucks

1 Answer

Replace fuel pump 1993 mazda 323



REMOVAL & INSTALLATION

323, Protege, 520-22 626 and MX-6 and 522-24 MX-3 Models
See Figures 1 and 2

  1. Relieve the fuel pressure and disconnect the negative battery cable.
  2. If not already removed, depress the clips on each end of the rear seat cushion and remove the cushion.



0900c152802612b0.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 1: Detach the fuel hoses and electrical connections from the fuel pump, then remove the attaching screws and the pump


0900c152802612b1.jpg enlarge_icon.gifenlarge_tooltip.gif

Fig. Fig. 2: Exploded view of the fuel pump assembly for the 323, Protege, 520-22 626, MX-6 and 522-24 MX-3

  1. If not already done, detach the electrical connector from the fuel pump/sending unit.
  2. Remove the attaching screws from the fuel pump/sending unit access cover and remove the cover.
  3. Disconnect the fuel supply and return hoses from the fuel pump/sending unit.
  4. Remove the attaching screws and the fuel pump/sending unit from the fuel tank.
  5. Detach the sending unit electrical connector, remove the sending unit attaching nuts and remove the sending unit from the fuel pump assembly.

To install:
  1. Attach the sending unit to the fuel pump assembly and install the nuts. attach the sending unit electrical connector.
  2. Install the fuel pump/sending unit into the fuel tank with a new gasket and install the mounting screws.
  3. Connect the fuel supply and return lines.
  4. Install the access cover and the mounting screws.
  5. Attach the sending unit electrical connector.
  6. Position the rear seat cushion over the floor, making sure to align the retaining pins with the clips. Push down firmly until the two retaining pins are locked into the rear seat retaining clips.
  7. Connect the negative battery cable, start the engine and check for proper system operation and for fuel leaks.

May 08, 2012 | 1993 Mazda 323

2 Answers

Fuel pump replacement


Fuel Pump - Multi-Port Fuel Injection models REMOVAL & INSTALLATION 1984-95 Models Fig. 1: Loosen the hose clamps and tag the fuel hoses before disconnecting them . . . 91075p07.jpg
Fig. 2: . . . then detach the hoses from the fuel pump module/sending unit 91075p06.jpg
Fig. 3: Disengage the fuel pump module/sending unit wiring harness connector 91075p05.jpg
  1. Disconnect the negative battery cable.
  2. Remove the fuel tank filler cap.
  3. Relieve the fuel system pressure as outlined in this section.
  4. Drain the fuel from the fuel tank.
  5. Raise and support the rear end on jackstands.
  6. Remove the fuel inlet and outlet hoses from the sending unit. Be ready to catch any spilled fuel.
  7. Disengage the sending unit wires. Fig. 4: The fuel pump module/sending unit retaining ring must be rotated counterclockwise for removal 91075p01.jpg

  8. Using a brass punch and hammer, remove the sending unit retaining lockring by tapping it counterclockwise. Fig. 5: Carefully pull the fuel pump module/sending unit out of the fuel tank - step shown with the fuel tank mounted on the vehicle 91075p03.jpg
    Fig. 6: Remove and discard the fuel pump module O-ring gasket 91075p02.jpg

  9. Remove the sending unit, which incorporates the electric fuel pump, along with the O-ring seal from the fuel tank. Discard the O-ring.
  10. Remove and discard the pump inlet filter.
  11. Disengage the fuel pump terminal wires.
  12. Remove the pump outlet hose and clamp.
  13. Unfasten the pump top mounting bracket nut and remove the pump. To install:
  14. Install a new inlet filter on the pump. Fig. 7: This is the proper positioning of the fuel pump module assembly inside the fuel tank 86745g55.gif

  15. Assemble the pump and bracket. Connect the hose and wiring.
  16. Install the unit and new O-ring in the tank. The rubber stopper on the end of the fuel return tube must be inserted into the cup in the fuel tank reservoir.
  17. Install the lockring. Carefully tap it into place until it seats against the stop on the tank.
  18. Connect the hoses.
  19. Engage the wiring.
  20. Lower the vehicle, fill the tank, run the engine and check for leaks.
1996-98 Models Fig. 8: Fuel pump module location - 1996 model shown 86745g52.gif
  1. Drain and remove the fuel tank as outlined in this section.
  2. Using tool 6856 or its equivalent, remove the module locknut which is threaded onto the fuel tank. The module will spring up when the nut is removed.
  3. Remove the module. To install:
  4. Install a new gasket and place the module into the opening in the fuel tank.
  5. Position a new locknut on top of the module and tighten the nut using tool 6856 or its equivalent to 40 ft. lbs. (54 Nm).
  6. Install the fuel tank as outlined in this section. Fig. 9: Locknut removal using tool 6856 or its equivalent 86745g56.gif
    Fig. 10: Install a new gasket on the fuel tank opening 86745g57.gif
prev.gif next.gif

Jan 19, 2011 | 1993 Jeep Grand Cherokee

1 Answer

My digital gas gage reads full all the time I have to go by my miles and sometimes that don't work and I run out of gas..how do I fix my problem


This is a common problem and to correct this problem will require the replacement of the fuel sending unit. The fuel sending unit is inside the fuel tank and has the fuel pump mounted in it. This requires the removal of the gas tank and then the fuel sending unit can be removed from the tank.

REMOVAL AND INSTALLATION Fig. 1: Fuel pump unit 8470h037.gif
  1. Disconnect the negative battery cable.
  2. Relieve fuel system pressure.
  3. Remove fuel filler cap to release fuel tank vapors. Leave cap off until repairs are completed. Gasoline fuel vapors are extremely flammable. Ensure that fuel is stored in a container that can be properly sealed. Never store fuel in an open container. Store container in a safe place away from heat.
  4. Remove fuel tank by performing the following:
    1. Step 1: Drain fuel from the tank into an approved container for storage.
    2. Step 2: Raise and safely support the vehicle.
    3. Step 3: Remove rear stabilizer bar at links, pivot bar downward.
    4. Step 4: Remove hoses and pipes from tank unit.
    5. Step 5: Remove hoses at tank from filler and vent pipe.
    6. Step 6: Disconnect tank unit harness from rear body harness.
    7. Step 7: Support fuel tank and disconnect 2 fuel tank retaining straps.
    8. Step 8: Remove tank from vehicle.
  5. Remove sending unit, gasket and pump assembly by turning cam lock ring counterclockwise. Lift assembly from fuel tank and remove fuel pump from fuel tank sending unit.
  6. Pull fuel pump up into attaching hose while pulling outward away from bottom support. Take care to prevent damage to rubber insulator and strainer during removal. After pump assembly is clear of bottom support, pull pump assembly out of rubber connector for removal. To install:
  7. Push fuel pump assembly into attaching hose.
  8. Install fuel tank sending unit and pump assembly into tank assembly. Use new O-ring seal during reassembly.
  9. Install cam lock over assembly and lock by turning clockwise.
  10. Support tank and position in vehicle. Install tank straps and secure with retaining bolts. Tighten to 25 ft. lbs. (33 Nm).
  11. Connect tank unit harness to body harness.
  12. Connect hoses to filler and vent pipes. Tighten clamps.
  13. Connect hoses and pipes to tank unit.
  14. Connect rear stabilizer bar to links. Tighten bolts to 42 ft. lbs. (58 Nm).
  15. Lower vehicle.
  16. Refill tank and install filler cap.
  17. Connect negative battery cable.
  18. Start engine and check for leaks.

Dec 24, 2010 | 1992 Oldsmobile Toronado

1 Answer

I JUST WOULD LIKE TO KNOW WHERE A FUELPUMP IS LOCATED ON MY 1999 GMC JIMMY TO SEE IF I CAN REPLACE IT ON MY OWN. THANK YOU!


it's inside the tank. Please let me know if you have more questions.


FUEL TANK REMOVAL & INSTALLATION
Except With Shield Package

  1. Properly drain the fuel tank, then disconnect the negative battery cable.
  2. If not done already, raise and support the rear of the truck safely using jackstands.
  3. If equipped on late-model vehicles, loosen and remove the tank plastic shield.
  4. Loosen the retaining clamp and disconnect the tank filler hose from the tank neck.

If fuel and vapor hoses or pump/sending unit wiring can be accessed at this time, they may be tagged and disconnected. If not, wait for the retaining straps to be loosened and lower the tank slightly for access.
  1. Tag and disconnect and accessible wiring or hoses from the top of the fuel tank.
  2. Have and assistant support the fuel tank, then remove the fuel tank-to-vehicle straps and, if equipped, the isolation strips. If no assistant is available, position a floor jack to support the tank while the straps are removed.
  3. Lower the tank slightly, then remove the sending unit or sending unit/pump wires, hoses and ground strap. Be sure to label all connections to ease installation.
  4. Carefully lower the fuel tank from the vehicle and store in a safe place.


Equipped With Shield Package
  1. Properly drain the fuel tank, then disconnect the negative battery cable.
  2. Raise and support the rear of the truck safely using jackstands.
  3. Remove the shield forward support and bracket.
  4. While supporting the shield and tank assembly with the help of both an assistant and a floor jack, remove the remaining bolts holding the assembly to the frame, then lower it sufficiently for access to the hoses and wires.
  5. Tag and disengage the hoses and wires from the sending unit assembly.
  6. Carefully lower the fuel tank and shield from the vehicle, then if necessary for service or replacement, separate the tank from the shield.


FUEL PUMP REMOVAL & INSTALLATION See Figures 5, 6 and 7

  1. Properly relieve the fuel system pressure.
  2. Connect the negative battery cable.

Be sure to keep a Class B (dry chemical) fire extinguisher nearby.


CAUTION Due to the possibility of fire or explosion, never drain or store gasoline in an open container.

  1. Drain the fuel tank, then remove it from the vehicle. Refer to the procedure found later in this section for details.
  2. Using the GM fuel gauge sending unit retaining cam tool No. J-24187, J-36608 (or equivalent) or a brass drift and a hammer, remove the cam locking ring (fuel sending unit) by twisting counterclockwise. With the locking ring released, carefully lift the sending unit from the fuel tank.
  3. Remove the fuel pump from the fuel sending unit, by performing the following procedures:
    1. Pull the fuel pump up into the mounting tube, while pulling outward (away) from the bottom support.


When removing the fuel pump from the sending unit, be careful not to damage the rubber insulator and the strainer.
    1. When the pump assembly is clear of the bottom support, pull it out of the rubber connector.


To install:
  1. Inspect the fuel pump hose and bottom sound insulator for signs of deterioration, then replace, as necessary.
  2. Push the fuel pump onto the sending tube.
  3. Using a new sending unit-to-fuel tank O-ring, carefully lower the sending unit/fuel pump assembly into the fuel tank.

When installing the sending unit, be careful not to fold or twist the fuel strainer or it may restrict the fuel flow.
  1. Secure the sending unit by turning or driving the lockring clockwise and into position under the tabs.
  2. Install the fuel tank assembly to the vehicle.
  3. Connect the negative battery cable and check for proper pump operation.

e4b833a.gif

Fig. Fig. 5: A special tool is usually available to remove or install the fuel pump locking cam


17a367b.gif

Fig. Fig. 6: A brass drift and a hammer can be used to loosen the fuel pump locking cam



74c9b76.gif


Fig. Fig. 7: Once the locking cam is released it can be removed to free the fuel pump

Oct 24, 2010 | 1999 GMC Jimmy

1 Answer

How do you replace the fuel pump on 2003 extend cab silverado


Hello;
The fuel pump is in the tank connected to the sending unit assembly. First drain the tank. Unfasten the hose clamps to the fill and vent hoses. Unfasten the hoses that attach to the sender. Unbolt the tank and lower to ground. Blow off the area where the sender is and take the retaining ring off. Pull the unit out and replace with the new unit.
Install is in the reverse order.
Note: I recommend you replace with the complete sending unit pump assembly rather than just the pump.
Thanks;
Rich
RPM Northwest

Jun 12, 2009 | 2003 Chevrolet Silverado 1500

1 Answer

How do you replace a fuel pump on a 1999 chevy blazer


Relieve the fuel system pressure if any. Wrap a shop rag around the Schrader valve located on the inlet fuel line of the fuel rail, right before the first fuel injector-the valve is similar to an air valve on a bicycle tire; then depress the small stem inside the valve using a small standard screwdriver to free the fuel form the line.
  1. Disconnect the black, negative battery cable; raise the rear of the vehicle using a floor jack and safely support it on 2 jack stands.
  2. Working from underneath the vehicle, disconnect the filler hose form the tank by removing the hose clamp using a Phillips screwdriver or ratchet and socket; then remove the Fuel tank shield using a ratchet and socket. Support the fuel tank with the floor jack and remove the tank mounting straps using a ratchet, ratchet extension and socket.

Lower the tank carefully, just enough to disconnect the two fuel hoses and vapor hose from the sending unit/pump assembly on top of the fuel tank. Press the lock tabs on the hoses connectors and pull the hoses form the assembly fittings; unplug the fuel pump electrical connector and lower the tank to the floor.

Remove the lock ring from the sending unit/pump assembly using a drift punch and hammer. Carefully rotate the lock ring tabs counterclockwise with the drift punch and hammer until the ring is free from the assembly. Lift the sending unit/pump assembly off the tank and out of the vehicle.

Install the new pump on the sending unit/pump assembly. Make sure the pump filter is in a horizontal position and does not interfere with the travel movement of the sending unit float arm; then install the sending unit/pump assembly into the tank using a new O-ring between the assembly and the tank.

Secure the assembly in place by turning the locking ring clockwise using the drift punch and hammer; then raise the fuel tank enough to connect the fuel and vapor hoses and plug the pump electrical connector.

Raise the fuel tank, install the tank mounting straps and tank shield; connect the filler hose to the tank and lower the vehicle; install the fuel pump relay and connect the black, negative battery cable. Start the engine and check for fuel leaks.

Good luck and hope this helps. It's about a 4 hour job from start to finish, also if your going to go through all that work. Buy a wire harness from the fuel sending unit to the frame. It's only around $15.00 and who knows, it may just be a bad wire harness that may be the problem.

May 02, 2009 | 1999 Chevrolet Blazer

Not finding what you are looking for?
2006 Suzuki GSX 750 F (Katana) Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Richard
Richard

Level 2 Expert

83 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...