Question about Motorcycles
Has it been stood months , is fuel good as it goes off after 6mths ! drain and replace ! P...
Posted on Dec 05, 2013
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
Based off of the limited information, the solutions are going to be generalized.
Visually check your battery for any acid build up. If you spot any, obviously some acid remove would be called for. Acid can sap a battery's output to a starter.
Visually inspect fuel components. Fuel injectors on bikes tend to get clogged when they sit for a while. Especially on older models. Refer to a repair guide for your specific model for guidance on the procedure to inspect fuel injectors.
Those two common starting problems for bikes. Without more information it is hard to offer a specific solution.
Posted on May 29, 2012
There should be 2 screws on each side which holds the light housing, losen then about 2 turns, adjust the headlight accordingly and tighten all back again. If you are doing it yourself, do it in your dark garage or at night time (dusk) so you can see the height you wanted.
Posted on Mar 24, 2010
YOU WILL FIRST WANT THE ENGINE HOT SO ALL THE OIL IN THE ENGINE WILL BE NICE AND THIN, 1ST PLACE THE MACHINE ON A SUTABLE PADOCK STAND AS THIS WILL AID REMOVAL AND GIVE SUITABLE CLEARENCE UNDER THE ENGINE FOR A CLEAN CONTAINER, WITH THE CONTAINER UNDER THE ENGINE TAKING CARE NOT TO BURN YOURSELF ON THE ENGINE OR ANY OTHER HOT PARTS OF THE BIKE , FIND A SUITABLE SPANER OR SOCKET, 17MM, SOME OF THE OLDER 1S USED A 14MM, REMOVE THE OIL DRAIN PLUG, IT MAY BE TIGHT,IT IS LOCATED UNDER THE BIKE AT THE LOWEST POINT ON THE ENGINE, THE OIL WILL BE HOT AND THIN AND MAY COME OUT QUITE QUICKLY SO TAKE CARE NOT TO SPILL ANY ON YOUR SELF. CLEAN AND INSPECT THE SUMP PLUG FOR DAMAGE TO THE SEALING WASHER, REPLACE IF IN DOUBT, REPLACE THE PLUG AND TIGHTEN ACCORDINLY DO NOT OVERTIGHTEN THIS AS DAMAGE MAY OCURE TO THE SUMP, WHEN YOU ARE SATISFIED ALL THE ABOVE WORK IS DONE YOU CAN THEN REPLACE THE ENGINE OIL, WITH THE CORECT AMOUNT AND GRADE FOR THE MACHINE, START AND RUN ENGINE, THEN AFTER A couple of miniuts RE CHECK THE OIL LEVEL, EASY JOB, SOME AMOUNT OF FINNESS REQUIRED.DONT RUSH THIS JOB.
Posted on Aug 10, 2010
Check you side stand safety switch . Suzuki uses a system that kills the motor if you put it in gear with the side stand down or put the side stand down while it is in gear and it is running.
Posted on Oct 02, 2010
Tips for a great answer:
Mar 26, 2017 | 2002 Suzuki GSX-R 600
Dec 26, 2016 | 2009 Suzuki GSXR600
Jun 12, 2016 | 2000 Suzuki GSX-R 600
Jan 01, 2016 | Mirror Block Offs-Suzuki - GSXR 600...
Nov 17, 2013 | Motorcycles
May 29, 2012 | 2001 Suzuki GSX-R 600
Apr 01, 2012 | 2001 Suzuki GSX-R 600
Oct 09, 2017 | 1998 Suzuki GSX-R 600
Oct 01, 2010 | 2001 Suzuki GSX-R 600
48 people viewed this question
Usually answered in minutes!