Question about Keeway Outlook 150 Motorcycles

1 Answer

I have a Keeway outlook 2012 scooter and the seal p/n 150013160000 located on the crankshaft broke and it's leaking oil on the drive-belt. The seal is not possible to find. How can I use a different seal which is 1 mm smaller in external diameter? How do I fill that millimeter in a very effective way? Thanks in advance for the suggestions.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 8 Answers

You cant
0

Posted on Oct 23, 2013

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 7 Answers

SOURCE: 2 stroke engine smokes. how do you adjust the fuel/oil mixture?

The thing with two strokes is that they smoke a bit under normal operation, and they smoke like mad if they haven't really been run for a period of time, I would advise you to run it for a while and see if that helps.

You should not need to adjust the mixture settings at all.


Hope this helps

Posted on Feb 08, 2009

  • 200 Answers

SOURCE: Can't get Keeway ARN to start

If you did not prep the bike for winter storage with Sta-Bil in your gas you might have some clogged carb problems You say this is a scooter but the description at top calls it a motorcycle. If it's a scoot then your engine and carb are underneath all that plastic your sittin' on.If it's a motorcycle your carb is right behind the engine between ur legs. It has a rubber gas line connected to it. Get some starter fluid from your local auto parts store and spray a short burst into the air cleaner and then hit the starter button. It should start but if it won't sit there and idle youv'e got a plugged card idle jet...time for a mechanic....next year prep the bike and disconnect the battery and you won't have to buy a new one....Good Luck !!

Posted on May 08, 2009

wd4ity
  • 4565 Answers

SOURCE: oil leak -between inner primary and transmission

There are several seals that can leak in this area. You say you replaced the mainshaft seal in the back of the primary. I've seen a lot of people replace this seal only to have it start leaking immediately. The reason was that they didn't know you must lubricate the seal before you reinstall the primary cover. When you put the primary cover on with the seal dry, when the engine starts up, the mainshaft immediately goes to 1000 RPM or higher with no lubrication on the seal. The friction burns the lip of the seal up before the lubrication in the primary can get there. It only take a second, literally.

Other seals that can cause leaks in this area are the large final drive gear seal in the face of the transmission behind the front belt pulley and the "Quad" seal that is inside the transmission. The Quad seal is almost like an O-ring. It's purpose is to prevent transmission lubricant from seeping out through the splines of the final drive gear. If the front sprocket splines wear and the sprocket gets the slightest bit loose, the compression on the Quad seal will be lost and the tranny will leak. The tale tell sign on this leak is that the transmission will leak a spot of oil about the size of a quarter or a bit bigger when you park the bike. If you wipe up the spot, it won't leak anymore until you either ride the bike or simply start the engine. Then it'll leak that quarter sized spot and stop. Check your lube level in your transmission.

Whenever I pull the inner primary and the belt on a Big Twin, I replace ALL the seals. Make sure you lubricate the lips on the seals so they don't cook before lubrication can get to the seal.

Good Luck
Steve

Posted on Jul 13, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much tire pressur for outlook keeway


The Keeway outlook 150 model 2012 owners manual recommends a pressure for both tires of 280 kPa (Kilo-Pascals) which means 40.61 pounds per square inch. However, I have a service manual that recommends 225 kPa which means 32.63 Pounds per square inch. I personally like high pressure (280 kPa) in my tires because the scooter feels more docile. I hope this answer fits you well.

Sep 23, 2014 | Keeway Outlook 150 Motorcycles

1 Answer

How much oil for keeway outlook 150?


You should change the oil on the keeway outlook 150 every 2000 Kmts and the old oil should be drained completely and add one liter.

May 22, 2014 | 2010 Keeway Outlook 150

1 Answer

2000 Mazda Protege 1.6L big oil leak passanger side. No oil in timing belt area. All over firewall & steering rack. What is leaking?


probably gaskets are not sealed properly you have to redo it or try and cleaned it remove all the oil that sorrounds the engine and try to seal with a high temp silicon

Jan 17, 2013 | Mazda 323 Cars & Trucks

1 Answer

Changing seals onfront diferentil half axles on 97 chavy astro


Its a long procedure.

Go through the related help links,similar to your issue:---
Click the link below:---
How to remove Front differential? http://howtobyme.blogspot.com/2012/01/how-to-remove-front-differential.html

---------
Timing Belt, Cover, Sprockets, & Seal replacing ? http://technoanswers.blogspot.in/2012/02/timing-belt-cover-sprockets-seal.html

-------------
Crankshaft Front Seal? http://schematicsdiagram.blogspot.com/2011/12/crankshaft-front-seal.html

-----------
Rear Main Seal Leaking? http://whatisbyme.blogspot.in/2012/05/2003-lexus-rx300-rear-main-seal-leaking.html

---------
Differential Chatters? http://whatisbyme.blogspot.in/2012/04/1996-toyota-prado-differential-chatters.html

---------
4x4 front differential will not engage the axle? http://technoanswers.blogspot.in/2012/02/4x4-front-differential-will-not-engage.html

-----------
CV AXLE stuck in Transmission? http://technoanswers.blogspot.in/2012/04/cv-axle-stuck-in-transmission.html

--------
These will help.For more help,keep updated.Thanks.

Nov 06, 2012 | Cars & Trucks

2 Answers

Squeaking while driving


jack up each wheel and turn them see if noise is comeing from wheel moveing or could be in drive train or worn out brakes squelers going off

Dec 12, 2011 | 2004 Kia Sedona

1 Answer

How do i change the belt on my 2009 keeway outlook scooter?


There's some work needed to be done on that. Download the service manual and buy the proper tools for that job.
https://www.scribd.com/doc/238408121/Manual-de-Taller-Keeway-Logik-Idioma-Ingles

Apr 02, 2011 | Keeway Outlook 125 Motorcycles

2 Answers

Oil Is Leaking Out Under The Harminc Balancer On my 92 Jeep Wrangler,4.0 6cyl. I Replaced The Main Seal & Put A New Balancer On & It Still Leaks From The Bottom Of The Balancer


  1. timing cover is leaking oil betwwen cover and block
  2. Disconnect the negative battery cable.
  3. Remove the drive belt(s), fan and fan shroud. If equipped, remove the accessory drive belt pulley.
  4. Remove the vibration damper retaining bolt and washer. Remove the vibration damper using a suitable puller.
  5. Remove the accessory drive brackets attached to the timing cover.
  6. Remove the A/C compressor, if equipped, and alternator bracket from the cylinder head and move to one side.
  7. Remove the oil pan-to-timing case cover bolts and the cover-to-cylinder block bolts.
  8. Remove the timing case cover front seal and gasket from the engine.
  9. Cut off the oil pan side gasket end tabs and oil pan front seal tabs flush with the front face of the cylinder block. Remove the gasket tabs.
  10. Clean the timing case cover, oil pan and cylinder block gasket surfaces.
  11. Remove the crankshaft seal oil seal from the cover by prying it out with a suitable tool.

To install:

  1. Install a new seal in the timing cover using a suitable seal installation tool.
  2. Apply sealer to both sides of the replacement cover gasket and position the gasket on the cylinder block. Cut the end tabs off the replacement oil pan gasket corresponding to those cut off the original gasket. Attach the end tabs to the oil pan with sealer.
  3. Coat the front cover seal end tab recesses generously with sealer and position the seal on the timing cover.
  4. Apply engine oil to the seal-oil pan contact surface, then position the cover on the cylinder block.
  5. Insert timing case cover alignment tool J22248 or equivalent, in the crankshaft opening. Install the cover-to-cylinder block bolts and tighten them to 62 inch lbs. (7 Nm). Install and tighten the oil pan-to-cover bolts to 11 ft. lbs. (13 Nm).
  6. Remove the cover alignment tool and position a replacement oil seal on the tool with the seal lip facing outward. Apply a light coat of sealer to the seal and a light coat of oil to the crankshaft. Install the seal on the timing cover.
  7. Apply a light film of oil to the vibration damper hub seal contact surface. Install the vibration damper using a suitable installation tool.

Do not hammer the damper into place as damage may result to the damper or engine.

  1. Install and tighten the crankshaft vibration damper bolt to 80 ft. lbs. (108 Nm).
  2. If equipped, install the crankshaft pulley and tighten the bolts to 20 ft. lbs. (27 Nm).
  3. Install the accessory brackets.
  4. Install the fan and fan shroud.
  5. Install the drive belt(s) and adjust to the proper tension.
  6. Connect the negative battery cable.
  7. Start the engine and check for leaks
  8. .

Jan 18, 2011 | 1992 Jeep Wrangler

1 Answer

How to chane battery on keeway outlook 125


You have to remove the lid that covers the battery on the floor of the scooter. There are only two screws to be removed and the battery is exposed.

Apr 08, 2010 | 2008 Keeway Outlook 125

1 Answer

1993 Dodge Stealth Oil leak 3.0 SOHC


there are seals behind the timing cover.when they leak oil drips down and out.my 93 base model leaks oil and coolant from this same place.

Apr 03, 2009 | 1993 Dodge Stealth

1 Answer

1999 cross country v70 awd crankshaft seal replacement


Your info is confusing. The rear cam seal is not inside the timing belt cover, and the crank seal is at the bottom of the engine, while the cam seal is at the top.

Is there oil at the top, around the cam seal? Or just at the bottom? It's common for the oil pump seal to leak. If you get the oil pump reseal kit, it contains the oil pump seal and gasket, as well as the crankshaft seal. Make sure you seal the oil pump bolts, Volvo has special copper washers for this purpose.

Just try to locate the oil leak before replacing any more parts. Sometimes it can be something simple like the oil cap seal or the oil trap housing.


Bret
RepairPal.com

Nov 23, 2008 | 1999 Volvo V70

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

120 people viewed this question

Ask a Question

Usually answered in minutes!

Top Keeway Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4536 Answers

Ron Stone

Level 2 Expert

197 Answers

Are you a Keeway Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...