Question about Motorcycles

1 Answer

I have a 2012 Speed Triple R, the indicators light up but don't flash. What would be causing this?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    An expert whose answer gotĀ voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 103 Answers

If you are saying that the turn signals stay on without flashing the common problems are:
1. The turn signals relay is broken or 2. The socket that connect wires to the relay has a imperfect contact. First try to remove the relay and clean the socket and the pins from relay with some contact cleaner spray. Also you could give some kick with the fingers to the relay. Could it be stuck. Please reply.

Posted on Oct 21, 2013

  • 1 more comment 
  • Tony Reynolds
    Tony Reynolds Oct 22, 2013

    Thanks for speedy reply. This has helped. Dealing with bike shop now to order part

  • Joita Constantin
    Joita Constantin Oct 22, 2013

    I don't know where the signals relay is located but on bikes is located behind the dash or in fuse compartiment or somewhere under the seat.

  • Joita Constantin
    Joita Constantin Oct 22, 2013

    Anyway, you told that your bike is from 2012? If so the bike should have warranty and all you have to do is to take the bike into service and pay nothing.



1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Caravan malfunction indicator light

The check engine light comes on when there is a fault or failure of a component within one of the systems.It will need to be checked for a fault then a diagnostic procedure routine will need to be done to determine the cause of the fault.If that check engine light is flashing while driving STOP and have it towed to the nearest shop,preferably a Chrysler dealer as they have the highest trained techs to correctly diagnose issues on any Chrysler product.

Apr 22, 2014 | 2012 Dodge Grand Caravan American Value...

1 Answer

Fault detection indicators

2012, is it under warranty? did you call them?
AC dead. at all vents.
the first check is,
  1. all fuses in cab and engine bad box good,
  2. fan on?
  3. fan actually blows on at least high? to any vent?
  4. does the compressor clutch ENGAGE?
  5. In USA we conn. our SCAN tool and SCAN all cars, no matter.

this is first , then up to 6 more checks.
but we stop here,

Jan 26, 2014 | 2012 Toyota FJ Cruiser Base 4dr SUV 4.0L...

2 Answers

How to reset engine lite in dash

Check engine light comes on and off, these are indication that there is some error code stored in your vehicles ECM. The engine module computer needs to be scanned. These will give the code and as per the error code the further problem can be detected and confirmed. The engine light indicator blinks or remains steady on dash when engine computer noticed any problem with any engine electrically operated components.

For more help, I suggest you to refer the help links provided below. These will let you know more about which areas to look, check, when there is engine light coming up on dash panel.


Click the link below: -------

Check Engine Light Reset Procedure?


Check Engine Light ON?


Intermittent Check Engine Light?


WHY Check Engine Light On car?


Check Engine Light, VSC light and Traction Control Light ON?


Check engine light flashing?

Service engine soon Light Turned OFF after Jump Start?


After replacing throttle body the Check engine light starts blinking?


2005 Chevy Impala: Service Vehicle Soon Warning Light?


Malfunction Indicator Light ON


Check power-train message with orange engine light came on?


2007 Toyota Highlander Hybrid: Yellow Check Engine Light ON dash?


1999 Toyota Tacoma: Check Engine Light Read Code P0171?


Car Runs Fine But Check Engine light is ON?


Check engine light with codes P2195 and P2197?


How to Read Codes from Check Engine Light?


Vehicle smog test failed Due to NO MIL/check engine light?


OBD Code is cleared but check engine light will not RESET?


Car jerks while going uphill and Check engine light is ON?


Toyota Camry Check engine light flashes while driving?


These details will help.


Nov 28, 2012 | 1999 Acura CL

1 Answer

Bluetooth wont charge or power on. when charging the red light comes on. once disconnected from charger it wont come on

Indicator Lights:
1.Headset Status Headset Indicator Light
2.Powering on Steady blue, then intermittent flashes
(changes to standby mode)
3.Powering off Red appears and goes off
4.Standby Blue intermittent flashes
5.Charging battery Red solid light. Light indicator turns off when
battery is fully charged and headset is off.
6.Low battery Triple red flashes
7.Pairing mode Blue/red alternating flashes
8.Missed call Purple flashes. Press the call control button
to cancel flashing light.
9.Incoming call Triple blue flashes when ringing.
Power on and off:
1.Turn on the headset Press and hold the call control button until the
indicator glows blue. You will hear ascending
2.Turn off the headset Press and hold the call control button until the
indicator glows red. You will hear descending
tones. When power is off, indicator stays off.
If none of this is helpful then it may be that your battery is dead, if that is the case then you will need to replace the whole headset. The battery's are not replaceable.

Good luck from Headsets Direct!

Sep 21, 2011 | Plantronics Explorer 220 Bluetooth Headset...

1 Answer

2007 triumph speed triple won't start. a while before it wouldnt start, it would periodically seem to drag while turning over. usually i could release the starter and push again and it was fine. that...

Hi, Suntaster66 and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a "LOAD" test, your battery may show 12.5 volts but has little or zero amps and must be replaced.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter.
5. Bank angle sensor needs a reset or is faulty.
6. FOB battery low or dead.
7. Faulty ignition switch.
8. Faulty starter button.
9. Faulty kickstand or clutch pull in switch/sensor.
10. Security alarm needs a reset.
11. Starter relay, solenoid or wiring faulty.
12. Starter armature or field coils have failed.
13. Main fuse or circuit breaker may be blown or faulty.
14. The electric starter is working but starter clutch has failed.
15. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
What to do When Your Motorcycle Won Start
Triumph Speed Triple Service Manual
Triumph Speed Triple User Manual

Mar 24, 2017 | 2007 Triumph Speed triple

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

54 people viewed this question

Ask a Question

Usually answered in minutes!

Top Motorcycles Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4825 Answers


Level 3 Expert

79123 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Motorcycle Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides