Question about 2011 Yamaha Roadliner Midnight

1 Answer

Speed sensor where is sensing unit localed

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert whose answer got voted for 20 times.


    An expert who has answered 20 questions.

  • Expert
  • 103 Answers

Probably is situated on the gearbox's carter.

Posted on Oct 20, 2013


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Where is the input speed sensor SC297 located

On the front wheels one each side senses the speed the wheels are rotating it generates a small DC voltage around .5v uses it as a referance to compare it to the third sensor VVS witch is senseing the output speed of the drive shaft at the rear of the transmission.

May 07, 2015 | 2004 Kia Sedona EX

1 Answer

Where odometer sensing device local?

Usually the speed sensor is on the gearbox's carter. If the bike has abs than probaly the speed is readed by the abs sensor.
Those are general informations, not special for you bike.

Oct 20, 2013 | Yamaha Roadliner Midnight Motorcycles

1 Answer


There are five speed sensors. There are four in every wheel area sensing wheel speed and the transmission has one at the end of the right side of it.
OBD2 code scanner

Oct 20, 2012 | Lincoln Continental Cars & Trucks

1 Answer

Check engine seems to only pop on when driven on the highway.Been driving it for weeks and it hasnt popped back on since my last highway travel, untill i drove on the highway today. I brought it to...

they could b referring to the vehicle speed sensor, which senses vehicle speed for input to ur ecm and not to ur speedometer. u most likely have 2 sensors with almost same name. their located on ur trans, an some sense input shaft speed an the others sense output shaft speed..... good luck hope this clarifies it for u a little bit

May 01, 2011 | 1999 Saab 9-5

1 Answer

Dsc warning light on , bmw e46

Dynamic Stability Control....a derivitave of ABS / Traction control. The control unit that monitors the dynamics will most likely be sensing a difference in the measured wheel speeds. Possibly defective ABS sensor, wiring, ABS exciter ring, ABS module or steering angle sensor. Can also be triggered by wheel spin.
Have a diagnostic scan done ( cost £30 - £50 approx at good local garage) to read the fault codes first. If you get a fault code relating to "ABS module pressure sensor" the module requires replacement (common issue). Used to be a £1400 job, but repair kit now available from dealer for £180 ish and 2 hours to fit.

Apr 27, 2011 | 2004 BMW 3 Series

1 Answer

Just installed speed only sensor self test on Matrix 17 finds everything else cannot find sensor, any tips welcome. Thanks Bill

the sensors position and the quality of the connection are important also reconnection when the device is starting up is when it senses new and current connections

Jan 14, 2011 | Humminbird Speed Sensor SW GPS Units

1 Answer

Engine cuts out when approaching a roundabout or junction, when slowing and clutch is down. Changed the speed sensor a few months ago which we thought had worked, problem came back yesturday

this is may be due to the idealing problem.set the idealing in correct amount so that it doesnt stops.

considering the speed sensors check any signal comin to the sensing unit is getting intruppted.

i think only these are the problem wihch may be the reason

Jul 09, 2010 | Ford Focus Cars & Trucks

1 Answer

What is an Error 22, 23,and 26 on a precor 9.35?

Error 22 indicates that the drive motor (running belt) has been instructed to start, by either manual or program control, and the monitoring system has not received any response from the speed sensing system indicating that the drive motor has started.
Error 23 indicates that the speed sensor signal was lost while the treadmill was in operation
Error 26 this error monitors the speed sensor signal and verifies the the speed sensor signal is appropriate for the requested speed. If the speed sensor signal is incorrect or erratic an Error 26 will be displayed.
Unplug unit and remove motor shroud and try these procedures:
The treadmill utilizes an optical (infrared) speed sensor and the line of sight between the speed sensor and the speed sensor target is obstructed. The speed sensor position relative to the speed sensor target is incorrect. The speed sensor potentiometer adjustment is incorrect (when equipped). The speed sensor target is damaged
Carefully, vacuum out the drive motor compartment with a static safe vacuum cleaner. Pay special attention to the area between the speed sensor and speed sensor target. Adjust the speed sensor position so that the space between the speed sensor and the speed sensor target is 3/16 inch and so that the speed sensor photo eye is aimed at the larger portion of the targets wedge shaped section. On hall effect speed sensors (magnetic sensor) the space between the end of the speed sensor and the flywheel tooth should be 3/16 inch. If the treadmill utilizes a speed sensor potentiometer, locate the speed sensor potentiometer on the lower PCA. Set the speed sensor potentiometer at mid-range. Start the treadmill and increase the speed to 6 mile per hour. Carefully adjust the speed sensor potentiometer to the point where the treadmill is operating the smoothest. Increase the treadmills speed to full speed at repeat the previous adjustment. These two adjustments are typically small and are usually only a matter of fine tuning. . Most speed sensor targets consist of a circular arrangement of alternate black and silver sections. If the speed sensor target is torn or badly scratched the speed sensor may receive an incorrect reading. Replace the speed sensor target.

Jun 25, 2010 | Precor 935 Premium Series Treadmill

2 Answers

What is a cam crank sensor on 2004 Audi A4

The "cam crank" sensor is the "reader" for position and speed of the camshaft. This sensor send informations to Engine Control Unit about camshaft position and speed. If the sensor is faulty engine stops!

Oct 23, 2009 | 2004 Audi A4

2 Answers

AVIC-N1 GPS not working

Have you tried calibrating the sensors? And is the speed sense working, i thing the unit relies primarily on the speed sense then on GPS. You can easily tell if the speed sense is woking on the calibration screen, as you drive the unit omits a bleep.

Sep 29, 2006 | Pioneer AVIC-N1 Car DVD Player

Not finding what you are looking for?
2011 Yamaha Roadliner Midnight Logo

Related Topics:

32 people viewed this question

Ask a Question

Usually answered in minutes!

Top Yamaha Experts


Level 2 Expert

281 Answers

Steve Sweetleaf
Steve Sweetleaf

Level 3 Expert

1144 Answers


Level 3 Expert

2600 Answers

Are you a Yamaha Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides