Question about Harley Davidson FXDWG - FXDWGI Dyna Wide Glide Motorcycles

1 Answer

Throttle sticking on 1984 harley davidson shovel head

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Harley Davidson Master
  • 40,868 Answers

Hi Anonymous, your cables are adjusted too tight or need to be lubricated, for more information on your question please visit the websites below and good luck:
Harley Davidson Throttle Cable Adjustment
How to Lubricate Throttle Cables on 2013 Harley Softail Deluxe

Posted on May 21, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: What type of oil does my 1978 Harley Davidson shovel-head use?

60 wt (50 if hi temp under 50f)

Posted on Apr 02, 2009

  • 1 Answer

SOURCE: Throttle to engine problem on 1993 Harley 883 Sportster

 You either need to lube the cables, or adjust them. You adjust the throttle to have a 16th to an 8th inch of freeplay with the bars like youre riding straight. You adjust the snap back with the bars fully to the right. As far as the motor shutting off , you need to use the enrichner ( they call it a choke) until it will idle on its own without rapping the throttle.  Also , your idle may be set too low on the carb. The adjustment is made at the idle speed screw , right behind the air cleaner. 

Posted on Sep 13, 2009

wd4ity
  • 4565 Answers

SOURCE: what is the float height setting for a 1984 harley

With the float bowl off and the float assembled in the carb, hold the carb on it's side with the needle and seat hinge upwards.

Set the float height to 0.630" to 0.670" (16-17mm) from the "bottom" of the float to the gasket surface where the float bowl gasket seal is.

These carbs are notorious for leaking past the needle and seat even when the float level is set correctly. They make a tool for refurbishing the seat in the carb as it is not replacable but the tool is very expensive for what it is and the amount of use will get out of it ($100). Sometimes I've set the float level an additional 1mm low (18mm) to put more pressure on the needle if it does leak. Good Luck!

Posted on Nov 13, 2009

wd4ity
  • 4565 Answers

SOURCE: how to change bearings in

Remove the rear wheel leaving the brake drum on the bike. There is one wheel bearing in the wheel. Drive it out with a hammer. The other two are in the brake drum, drive them out with a hammer as well. These are sealed beaings.

good luck,
Steve

Posted on Aug 06, 2010

  • 1 Answer

SOURCE: looking for oil line diagram

c81a64b0-e4ac-4fc6-952f-2c59f78a9fdb.jpg hope thid helps

Posted on May 01, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1984 Harley Davidson FLHX


I believe it should be a 2:1

However, your old speedo should have the ratio on it's underside.
Take it off and turn it over and see if it's indicated there.

Feb 18, 2014 | Motorcycles

1 Answer

WHAT IS AND HOW TO DIAGNOSE STARTER DRIVE ON FLHTC 1340CC HARLEY


Hi Anonymous, it sounds the like starter drive/clutch has gone south, it has components inside, that when spinning, centrifugal forces cause them to grab or lock into permanently fixed counterparts. The gear only spins one way and locks the other way. If you have one that spins both ways it makes a noise like the starter is just spinning, it has failed and needs to be replaced. Please visit the web site below for more help. Good luck and have nice day. Harley Davidson Manuals Mark Workshop
2005 Harley Dyna FXDX starter replacement

Oct 22, 2012 | Harley Davidson FLHTC Electra Glide...

1 Answer

Installing time gears on FLH 1200 harley davidson


Hi Anonymous, for more information on your question please visit the websites below and good luck:
picture of shovel head cam timing marks Google Search

Sep 03, 2012 | 2003 Harley Davidson XL 1200 C Sportster...

1 Answer

How to take cam out of a 1977 shovel head


Hi Homeboy, for more information about your question please visit the websites below. Good luck and have nice day.
Harley Davidson Shovelhead Engine rebuild 01

Aug 25, 2012 | Harley Davidson Motorcycles

1 Answer

Ignition wiring diagram for 78 shovel head harley


Hi Anonymous, for a free wiring diagram please visit the website below and good luck.
Harley Davidson Wiring Diagrams and Schematics

May 05, 2012 | 2002 Harley Davidson FXDL Dyna Low Rider

1 Answer

I have a 1984 FLHS Shovel. It is pumping oil out of the crankcase breather tube.


you either have too much oil in there or the engine needs rebuilding as the rings/bore will need sorting out.

Mar 18, 2011 | Harley Davidson FLHT Electra Glide...

1 Answer

1982 Harley davidson shovel head , i need the topend bolt torque spec's


I always pull them to 70 foot pounds in a criss cross pattern. Start the engine up and allow it to warm up. When cool, retorque the heads in the same manner. I only use Fire Ring head gaskets.

Good luck
Steve

Aug 09, 2010 | Harley Davidson FLHT Electra Glide...

2 Answers

Wat kind of oil should i use on my harley fatboy


the motor company says use only harley davidson 30 wt or better, but I use regular old motor oil.

Jul 09, 2010 | Harley Davidson Harley-Davidson Motorcycle...

1 Answer

My 1980 Harley FLT shovel head is making louder then normal sounds and seams to get hot. I think maybe oil pump?


Shovel head lifters tend to wear out. Check your adjustment first. Shovels also run on the warm side. Does it idle good? If not, check for intake leaks.

Apr 15, 2010 | 2000 Harley Davidson FLHT Electra Glide...

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...