Question about Daelim Motorcycles

Open Question

Handlebar size i am replacing the mirrors on my daelim vs 125cc motorcycle for bar-end mirrors i need to know the size of the handlebars

Posted by Anonymous on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 72 Answers

SOURCE: Harley Davidson Ultra classic handlebar replacement

1.cover the tank with towls beachtowls 2.remove switches,unbolt both ,clutch and front brake from bars,leftside grip pry under it with a flat crewdriver and spray under it with hairspray and turn on it to make it come off, right side loosen the bars and move them so when you loosen the rightside it can come right off.unbolt the bars from center of the bars

Posted on Mar 27, 2009

  • 136 Answers

SOURCE: Need part number for 2005 883C stock handlebars and recommendatio

56021-04B
Fits ’04-’06 XL883C . i have the bars if you are intrested i could list on eby. find me on fb m. loud.

Posted on Aug 19, 2009

Testimonial: "Hope I can find him or he finds me... jflyer2@aol.com"

stephensaon_
  • 284 Answers

SOURCE: needing diagram of how to tighten handlebars on motorcycle

You have to remove the headlight, then the Nacelle ( passing lamps if you have them ) Under the lock ( which is removed with a small flat head screwdriver ( it's held in by 3 little push in tabs ) There are 2 phillips head screws( remove them ) then once you have the headlight out, there is a 5/16 nut holding the top chrome spine in place. Remove the nut lift the spline. then remove the nacelle one side at a time. Once you remove the nacelle the 1/4 allen bolts are right there to tighten. Make sure you tighten them evenly. Reverse steps to re-install back to normal.

Posted on Aug 27, 2009

4ucustom
  • 42 Answers

SOURCE: replacing forward controls and handlebar grips.

all harley bars are 1" dia

Posted on Feb 08, 2010

  • 3799 Answers

SOURCE: Handlebar size for Intruder 1400 1992 GLPN

From the information I have found it would seem to be 7/8"

Posted on Jun 11, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I'm too tall :s


I don't know what the laws are in Norway, here in the Colonies, it is generally legal to change stock handlebars for after market handlebars. I wouldn't modify the handlebars by welding, myself. If I were so inclined, I would purchase what we call "Ape Hangars". We have some ridiculously huge handlebars available in the aftermarket market. To my mind, they cannot be comfortable to use and there are probably some safety concerns. Then there is the wiring that must be extended. Affect resale? Depends upon who you expect to sell to. I wouldn't be the slightest bit interested in a bike that was not stock ... but that is just me. Check here: https://www.google.com/#q=ape+hangers&hl=en&source=univ&tbm=shop&tbo=u&sa=X&ei=wGMrUdr7MYW_0QHWkYG4CQ&sqi=2&ved=0CGEQsxg&bav=on.2,or.r_gc.r_pw.r_cp.r_qf.&bvm=bv.42768644,d.dmg&fp=8c456d1ca700482f&biw=1267&bih=800 or Google "Ape Hangers"
You can get your legal question aswered at your police department ... just ask them.
Thanks for your interest in FixYa.com

Feb 25, 2013 | 2007 Daelim Daystar

1 Answer

How do i change handlebars on a 2010 Dyna


Unplug the handlebar wires where they connect to the wiring harness. Remove the black electrical connectors at the end of the wires. Pull the wires through the ends of the handlebars. Silicone lubricant sprayed into the bars will make this a bit easier, and you should be able to leave the silver pins on the ends of the wires, saving yourself some work when installing your new bars. Leave the wires connected at the handlebar controls when doing this. Just unscrew the controls from the bars and pull the wires.

Aug 21, 2012 | 2000 Harley Davidson FXD Dyna Super Glide

1 Answer

Handlebars won't stay straight.


If your handlebars don't appear to be straight, the pinch bolts on the lower triple tree may be loose or the rubber handle bar riser bushings need to be replaced. Either way, you'll have to remove the "Tins" from the front end of your Fat Boy to access this area.

Good Luck
Steve

Sep 20, 2011 | 2006 Harley Davidson FLSTFSE Screamin...

1 Answer

My throttle won't snap back. I recently packed the end of the handle bars with silicon to help with vibration. Now my throttle sticks and won't snap back right away. How can I fix this?


I'd be willing to bet that you have gotten silicone on the outside of the bars between the handlebar and the throttle sleeve. But, let's try this first. Loosen the two screws that hold the right handlebar switch halves together. Once you get them loose, slide the throttle assembly and the switch housing towards the end of the handlebars about an 1/8" or so. Not much, just a bit to make sure the end of the handlebar is not rubbing inside the throttle grip at the very end. Tighten the screws and try the throttle now. If it works, tighten the two screws securely and loosen the bolts for the front brake master cylinder and slide it down against the handlebar switch housing so you brake light will work correctly.

If this doesn't work, try loosen the cables just a bit. If they're adjusted too tight, the throttle will stick.

If that doesn't work, you'll have to take the throttle sleeve back off the handlebars. Clean out the inside of the sleeve and the handlebars good. Then apply a thin even coat of white lithium grease to the inside of the throttle sleeve and on the outside of the handlebar. Slide the sleeve uo on the handlebar and work it around to make sure it moves absolutely freely. Then reconnect the cables and reassemble the switch housing. Adjust the cables and make sure the throttle works as it should.

Good Luck
Steve

Feb 11, 2011 | 2003 Harley Davidson XLH Sportster 883...

1 Answer

I am trying to install Z Bar handle Bars on my Harley Davidson. I need install instructions on how to thread the wires.


I assume you are talking about running the wiring internal of the new handlebars and you need to know how to pull the wires through the them. You need to get a "fish tape" through the bars. The easiest way to get the fish tape into the bars is to start off by getting a string through them.

Use a shop vacuum and connect it to one end of the bars. Plug the other end of the bars temporarily. Turn on the vacuum cleaner and feed a string in from the hole in the center of the bars. If the bars are not too rough on the inside, the string will be sucked out the end of the bars.

Once you get the string through the bars, form a loop on the end of a scrap piece of wire and use the string to pull it through the bars. Now, use the wire to pull the switch wiring through the handlebar.

You may want to put some type of "sleeving" over the switch wiring so that you don't skin the insulation off the wires as you pull them through the handlebars.

Good Luck!!

Oct 30, 2009 | 2004 Harley Davidson VRSCA V-Rod

2 Answers

I need 2 modify my bajaj discover to some sporty looks wht can i do???


Removing some of the parts from yor bike ll give you sporty lok. 1. Replace the chain guard with semi covered one 2. remove the saree guard 3. remove the original handlebar and install 3 peice handle bars. 4. increase the size of rear suspension. (this can be done by increasing the size of the metal holder in bottom end of the suspension).
Rate this!!

Jul 28, 2009 | Bajaj Discover Motorcycles

1 Answer

Trying to find a new or second hand rear light lens for daelim vs 125 2002 reg


im too looking for a rear light cover for the Daelim vs custom 2004 125cc can anybody help me? please contact me here asurridge@hotmail.com

Mar 09, 2009 | 2002 Daelim VS 125

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daelim Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Joseph Hoffmann

Level 3 Expert

1702 Answers

RAYMONDO1953

Level 2 Expert

545 Answers

Are you a Daelim Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...