Question about 1993 Suzuki VS 1400 Intruder

1 Answer

What is an inlet manifold - 1993 Suzuki VS 1400 Intruder

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

This is the part of the engine where the fuel/air mix is supplied to the combustion chambers. In a fuel injected engine, it only supplies air.

Posted on Oct 19, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a gasket between motor an carb there is a neapreen inlay where it bolts on


The rubber inlet manifold fits onto the cylinder but inside the rubber is a small 'pipe' that must fit into the small hole on the cylinder block otherwise there will not be sufficient vacuum created as the piston rises to drive the diaphragm in the carb. It is easier to fit the inlet manifold rubber to the cylinder before putting it back into the housing. Between the carb and the inlet manifold is a thin plastic 'gasket' with a small pipe. That pipe fits into the vacuum hole on the inlet manifold. Often when the machine is dismantled the inlet manifold will not go back right - it will either be less flexible or gone hard over the years so a replacement is necessary. The Stihl part is expensive but aftermarket ones are available.

Nov 02, 2015 | Stihl 16" Chainsaw Bar Chain Saw 018 025...

2 Answers

Water on spark plugs on starting is it a blown gasket


not necessarily
have a compression test done first to eliminate the gasket
other points are: - the inlet manifold v motors use a passage in the inlet manifold to cross water between the heads at the back
if your motor is a v motor (not included in the question ) then there could be a corrosion hole in the manifold letting water in to the combustion chamber
corrosion in the head that is allowing water to the inlet manifold --won't show up in a compression test as it will be on the inlet side of the valves
any problems such as a blown head gasket , cracked head or corrosion in the combustion chamber will result in overheating of the engine so the problem ( if the compression test is good ) will be corrosion in a part that is connected to the inlet manifold such as a EGR valve

Jun 29, 2015 | Cars & Trucks

1 Answer

1991Buick skylark stall when hitting brakes


Check the brake booster. It is connected to the inlet manifold as it uses the vacuum coming from the inlet manifold. A leaking diaphragm might cause to much air entering the inlet manifold. Start the engine and let it idle - check that it doesn\'t idle to low, if so adjust first - step hard on the brake pedal as during an emergency stop. If the engines stalls it is the brake booster.

May 09, 2014 | Cars & Trucks

1 Answer

Runs good idle but when give gas cut off


sounds like a carburation problem to me
(1)
may be your choke is not switching off when you push the lever
and is seized where it joins the carburetor
get some light oil and lubricate the cable and take the choke mechs apart and clean it up then reassemble
(2)
cracked inlet manifold carburetor (connecting pipe)
it sounds like a damaged air filter or a cracked inlet manifold

if it is a cracked manifold
a quick get you home trick is to remove your carburetors
get 4 condoms put the condoms over the inlet manifold
cut holes in the end to refit your carbs
reassemble the bike
to get you home on the way home call in at your local motorcycle spares shop and order some new inlet manifolds

order a new air filter while you are there as well

hope this helps out

ride safe

May 07, 2014 | Honda CRF 100 F Motorcycles

1 Answer

2004jaguar s-type 4.2 liter water leak in back of manifold


there are 2 hoses that run under the inlet manifold that are prone to failing. also the plastic tower at the front of the inlet manifold on top of the engine can leak from its o ring seal where it bolts to the cyl, block. have a look if you can see coolant under the inlet manifold, you may have to remove the manifold to locate the problem area. hope this helps. i am a retired jag. technician.ps. there are also coolant hoses on the throttle body that can fail.

Aug 16, 2013 | 2004 Jaguar X-Type

1 Answer

What does IMT stand for


Refers to the Inlet Manifold Tuning Valves, two large black valves on the top or side of the inlet manifold. The O rings can fail on these and the inlet manifold can get contaminated with oil. check out Jaguar Technical Info XT303-13 here http://www.bluejag.co.uk/technical-bulletin.php

Aug 07, 2013 | 2005 Jaguar X-Type

1 Answer

I need instructions on how to replace a fuel pressure regulator and intake gasket manifold in a 1994 Toyota 4runner. Do you know where I can get that information?


The pressure regulator should be fitted ot the fuel rail firewall end and the inlet manifold gasket on the inlet manifold when you take it off ,and the inlet manifold is the one which goes to the air filter pipe and airfilter box.

Nov 18, 2009 | 1993 Toyota 4Runner

2 Answers

FOCUS 1.6 ZETEC CLIMATE TDCI 2006- FAULT CODE P242F


If the cat was blocked you would have noticed a massive power loss and your speed would have been down to - 40kph

If that was the case then yes the cat has collapsed and needs replacing

Jun 30, 2009 | 2005 Volvo S40

1 Answer

Air leak on inlet manifold gasket


ive got a vw bora 2.3 v5 2001 got a hissin from inlet manifold

Apr 14, 2009 | Volkswagen Passat Cars & Trucks

Not finding what you are looking for?
1993 Suzuki VS 1400 Intruder Logo

52 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...