Question about 2007 AMERICAN IronHorse Texas Chopper

1 Answer

Front right signal and back right stop light not

Front right signal and back right stop light not working but others are

Posted by Anonymous on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • AMERICAN Master
  • 41,636 Answers

Hi Anonymous, before diagnosing any turn signal issue make sure the bulb is good and the light fuse has continuity. If no turn signals work the cause could be a faulty turn signal module or the connector going to it, look for corroded, loose, or broken pins/sockets. Contact spray cleaner is great for removing corrosion. If your speedometer does not function properly it will have to be fixed first because your turn signal module gets the data from the speedometer for normal turn signal function. If your front turn signals don't work use a test light to check for power and ground at the bulb socket, then start backtracking the wiring through every wire connector to the turn signal switch/button and check for continuity, go all the way back to the fuse if necessary to find the cause of the malfunction. If your rear turn signals don't work check your rear fender wiring harness connector first for corroded, broken, loose pins/sockets, power, and a good ground, (the harness connector is usually located under the seat on the front of the rear fender) then keep tracing the wiring look for obvious harness damage caused by the rear tire. If you still can't find the malfunction backtrack from the rear fender wiring harness connector. If one side does not work you could have a faulty turn signal switch or module check for continuity. For more information about your issue, please visit the websites below. Good luck and have a nice day. service manuals

Posted on Oct 12, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Front right and back right turn signal wont work but the front left and back left do


first check the bulbs on that side by visual or changing to the other side if you can't see that well if the bulbs from the front and back work or are good when checked the flasher has blown out on one side and you have to replace it other possible cause could be a broken wire for the right side lights so look at the connectors for that side front & back if all is good one more thing could do this the actual turn signal lever that you use to activate the signals could be bad for the right side especially if it does not go back to the normal position after making a turn and the steering wheel rotates back to it's normal position but the turn signal lever does not click back to the center position this would burn out that side from the signal constantly being on good luck stephen

Jan 03, 2015 | 1991 Ford Probe

1 Answer

If one turn signal light burns out do the other 3 stop working


If you have one in the front and two in the back, on one side, one bad bulb can make the other two light up but not flash. Each side is separate from the other side.

Apr 25, 2013 | Cars & Trucks

1 Answer

On my 2004 impala, the front right turn signal doesn't work, (only works with hazard lights). And the back right signal is fast. The signal "clicking" sound is non stop but on the other hand...


If the turn signal filament of the right front park/turn lamp is known to be OK and the hazard switch is in the normal position, the hazard switch or the turn signal/multi-function switch could be defective

Oct 16, 2012 | Cars & Trucks

1 Answer

Town and counrty front right signal light flashing faster, rear light stop flashing


the signal indicator lights are suppose to flash in perticular time interval which is connected to a timer relay when the light flashes faster that means the other light is not working and the relay is getting double the current and moving faster so check the other light either the bulb is fuse or the current is not reaching up to the bulb

Aug 22, 2012 | 2005 Chrysler Town & Country

1 Answer

2009 Impala rear lights not working


Turn Signal Lamps
The LT T/SIG and RT T/SIG fuses located in the underhood fuse block supplies battery positive voltage to the body control module (BCM) for turn signal and hazard lamp operation. When the turn signal switch is place in either the LEFT or RIGHT position, ground from G202 is applied through the turn signal switch signal circuit to the BCM indicating the turn signal request. In response to this signal, the BCM applies a pulsating voltage to the front and rear turn signal lamps supply voltage circuits cycling the lamps ON and OFF. The BCM also sends a message via GMLAN to the instrument panel cluster (IPC) to cycle the turn signal indicator ON and OFF depending on the position of the turn signal switch.
Ground for the turn signal lamps is supplied as follows:
• G101 provides ground for the left front turn signal lamp
• G100 provides ground for the right front turn signal lamp
• G302 provides ground for the left and right rear turn signal lamps

The LT T/SIG and RT T/SIG fuses located in the underhood fuse block are also used by the body control module (BCM) for stop lamp operation.
The brake pedal position sensor is used to sense the action of the driver application of the brake pedal. The body control module (BCM) provides both, a 5-volt reference voltage and low reference to the brake pedal position sensor. The position sensor provides an analog voltage signal back to the BCM that will increase as the brake pedal is applied. When the brake pedal is applied, the BCM will then apply battery voltage to the left and right stop lamp supply voltage circuits and the center high mounted stop lamp (CHMSL) supply voltage circuit illuminating the stop lamps. At the same time the BCM signals the transmission control module (TCM) and the engine control module (ECM) that the brakes are applied. Ground for all stop lamps is provided at G302.
The stop lamps on this vehicle will not illuminate unless the ignition is in the accessory, run, or crank positions. When the ignition is in the OFF position the stop lamps will not illuminate when the brake pedal is applied.

Did you check the fuse's. ? Wouldn't think it's a ground because right an left tail lamp Assembly's use same ground ! Did you check for B+ voltage at the bulb. with a volt meter ? Power is supplied by the BCM . Could be the tail lamp assembly

Jul 19, 2017 | Cars & Trucks

1 Answer

Back signal blinks fast no front signal


Right front signal bulb not working (burnt or disconected). Check bulb and connections.

Nov 02, 2011 | 2011 Chevrolet Traverse

1 Answer

2001 Toyota Tacoma- turn lights not working and cruise control


fuses???
Check relays.....
Harness grounds, engine ground,
Check the trailer harnes for short.
Vitally

Jun 02, 2009 | 2001 Toyota Tacoma

1 Answer

Front turning light does not work, i replaced the bulb, and when i turn the truning signal does not turn off.


Sounds like you have a bad ground. Follow the wiring harnesses under the hood and in the trunk, there should be a ground wire going to the chassis or to the body. If they are all clean and tight, you might be looking at a bad light socket.

May 28, 2009 | 1996 Dodge Neon

Not finding what you are looking for?
2007 AMERICAN IronHorse Texas Chopper Logo

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top AMERICAN Experts

David Payne
David Payne

Level 3 Expert

14161 Answers

Larry Maranto

Level 2 Expert

198 Answers

richie46

Level 3 Expert

12962 Answers

Are you an AMERICAN Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...