Question about 2011 Dafra Citycom 300i

1 Answer

Start problems Dear Expert, my Dafra Citycom 300i does not start anymore even though the battery seems to be ok (lights are on and so is the panel). The problem appeared slowly, in the beginning i needed to push the start button a few times before the engine kicked in. Then it got worse and this morning the scooter just would not start. Many thanks in advance for your help.

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 108 Answers

Same with most chinese motorcycles and scooters
take the wiring blocks out and solder the wires in place
as the wire blocks are useless

Posted on Oct 18, 2013

Testimonial: "Neil, thanks for the advise. I must admit my ignorance, I do not know what wires you are referring to. Btw, I just replaced the battery (many people told me to do so), but nothing changed."

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kymco downtown 300i oil light stay on and won't start


Hi, Michael and the usual suspects are:
1. Ignition Switch not in the "ON" position.
2. Engine Run Switch in the "OFF" position.
3. Discharged battery, needs to be 12.5 volts or better and be able to pass a load test if necessary.
4. Check the battery terminals for damage or corrosion check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
5. Tip over sensor needs a reset.
6. Faulty ignition switch.
7. Faulty starter button.
8. Faulty kickstand or clutch pull in switch/sensor.
9. Starter control circuit, relay, or solenoid faulty.
10. Main fuse or circuit breaker may be blown or faulty.
11. Check for engine trouble codes.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day
Downtown 300i Won Turn Over
http://meiguohosting.com/How-to-fix-start-problem-for-your-2011-Kymco-Downtown-300i
KYMCO People GT 300i Service Manual
Downtown 300i Kymco Scooter Parts Racing Planet USA
KYMCO downtown 300i Owner Manual

Feb 26, 2017 | 2013 Kymco Downtown 300i

1 Answer

Does sym citycom 300i start with a burned rectifier


Hi, Ntina_poulop and the usual suspects are:
1. Fouled spark plugs.
2. Severely discharged or a damaged battery, should have 12.5 volts or better and be able to pass a load test if necessary.
3. Check battery terminals for damage or corrosion, check the battery cables at "BOTH" ends for loose, corroded, or broken connectors, "INSIDE" and outside the cable harness, perform connector wiggle test and check cables with an ohmmeter if necessary.
4. Loose connection at ignition coil or plug between ignition sensor and module.
5. Spark plug cables in bad condition, shorting / leaking, spark plug cable connections loose.
6. Faulty ignition coil or electronic control module or CDI box.
7. Faulty CKP, CMP, or BAS sensor.
8. Faulty ignition switch.
9. Tilt sensor needs a reset.
10. Security alarm failing to disarm needs reset
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
Sym Citycom won start 1200km
Piaggio Won start
http://symcity.altervista.org/wp-content/uploads/2013/01/CITY-COM-Service-Manual_noPWg.pdf
SYM Citycom 300i User Manual

Jul 13, 2016 | 2008 Sym Citycom 300i

1 Answer

How to remove the rear wheel of a sym 2013 300i gts scooter


remove the silencer first and then the rear wheel is accessible

Apr 13, 2014 | 2010 Sym Citycom 300

1 Answer

Main fuse?


HAVE A LOOK AT THE SPARK PLUG IT COULD BE THAT IT NEEDS REPLASING

Oct 18, 2013 | 2011 Dafra Citycom 300i

1 Answer

Wpn824NA Not working


Hello.
If the test light on the router stays on after 20 seconds, even after turning off the router and back on it stays lit, it means the router has a problem.
What you can try to do is reset the router to factory settings:1. With the router powered on, hold down the reset button on the back of the router for 20 seconds until the test light on the fron panel turns on.2. Release the reset button and wait for the router to restart and become stable.
If the test light does not stay on anymore, the router should be ok, you need to set it up again though.
Hope this helps. Glad to be of service.

Nov 24, 2011 | NetGear Computers & Internet

1 Answer

Wont start


Start by checking the battery connections. If they seem okay then, even though it may be pretty new, I would take the battery to the dealer and have them check it for an internal short in the battery. I had this happen 2 weeks after picking up a new car.

Mar 14, 2009 | 2004 Dodge Durango

1 Answer

Machine won't start


My friend got somebody in to fix it in the end. It actually did turn out to be a problem with the door switch. I don't think it was able to lock it's self properly even though the light was on. (Don't know the exact details though). Think they guy just played with the lock to sort it out rather than getting a new part. I noticed when I played with it that if you got the door open, pulled out the plug and switched it back on again it would make a clicking noise for a while as if it was trying to shut it's self if this is any help? Mark.

Oct 21, 2006 | Zanussi WJS1265W Front Load Washer/Dryer

1 Answer

Machine will not start.


Hi I am not an expert but, have you looked to see if the pressure swithch is blocked?

Oct 04, 2006 | Zanussi WJS1265W Front Load Washer/Dryer

Not finding what you are looking for?
2011 Dafra Citycom 300i Logo

167 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dafra Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

kakima

Level 3 Expert

102366 Answers

Are you a Dafra Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...