Question about Qianjiang Motorcycles

1 Answer

Motor running fast - Qianjiang Motorcycles

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Night Owl:

    An expert who has answered 10 or more questions between 12 midnight and 6am on the same day.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 79 Answers

You may just need to locate the idle adjustment and turn it down a bit.

Posted on Oct 22, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

On a 1976 115 hp johnson boat motor i have to hold choke in to get it to run fast


remove and have the carburettor serviced as what that indicates is blockages in the main jets and circuits
could be corrosion from, or water in the fuel

Jun 07, 2015 | Boating

1 Answer

Hegner motor fast


you might need a new switch

Mar 30, 2014 | Saws

1 Answer

Motor is running fast when i start it chock seems to stay closed engin light is on


A 2000 Isuzu would have fuel injection not a carb, so no choke is used.
You would need to get the computer checked for trouble codes, I would suspect a huge vac leak is the cause of the fast idle.

Jan 31, 2014 | 2000 Isuzu Rodeo

1 Answer

Need schematic


Most of the time when the motor is running to fast it's the pinch roller not doing its job it may need cleaned.

Aug 17, 2012 | RCA RP3503

1 Answer

Its actually a B1500 3.9 v6 my question is on the oil guage its at about 30 when i start driving it go to about 100 but when i stop it go back to 30 is this normal


Yes, this is normal what is going on is that your oil pump is not spinning as fast. your pump runs off the motor and the fast the motor goes ( rmp ) the fast the pump spins and pumps. the motor dose not need as much at low rmp as high rpm. look up toroidal oil pump.
Mark
C.C. Motorsports

Feb 24, 2010 | Dodge Ram B150 Cars & Trucks

1 Answer

1985 gmc k1500 wipers only move at 1 slow spped, interminttent doesnt work at all. How fast is fast and why is fast not working?


Slow is the same speed as 'mist'. Mist is when you twist the control arm backwards to induce a single swipe. If you hold it, you will run the wipers in low speed. Fast is faster than that. Probably by 30% or more.

Turn the wipers on high speed. Wiggle the connector at the wiper motor. If the wipers run sporadically as you wiggle the connector, you either have a bad connector or a bad circuit board on the wiper motor.


Jan 15, 2010 | 1985 GMC K1500

2 Answers

My side by side was not very cold.


you will have to replace the condensor fan motor

Jul 01, 2009 | Whirlpool GC5SHEXNS Side by Side...

1 Answer

I have a sony TC 530. Fast fwd and rewind work


You need to replace the motor run capacitor. It's a small aluminum can looking thing with three wires right next to the motor; they often leak paraffin wax into the bottom of the case when they overheat. Whether or not yours has leaked it's easy to replace if you can use a soldering iron. Search eBay for a Sony reel to reel 1.5uf 250VAC motor run capacitor - they're less than $15 and come with detailed instructions.

Please wait Image not available
s.gif

Jun 14, 2009 | Quantegy 456 Reel-To-Reel Recording Tape

1 Answer

Motor is sluggish, Necchi Model#4795


Set machine to wind the bobbin to check for how fast the machine will run. I believe it will run fast or slow according to how hard you depress the foot control. If it runs fast and slow you have a problem in the machine. Most likely the machine, if turned by hand, is hard to turn and it needs to be professionally serviced. before it is ruined.
sewman7

Dec 29, 2008 | Sewing Machines

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

30 people viewed this question

Ask a Question

Usually answered in minutes!

Top Qianjiang Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

GQ-ROD

Level 3 Expert

635 Answers

Steve Luck
Steve Luck

Level 3 Expert

817 Answers

Are you a Qianjiang Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...