Question about 2000 Harley Davidson FXSTS Springer Softail

1 Answer

WIRING DIAGRAM FOR 2000 HARLEY FXST CHANGED HANDLEBARS AND TURN SIGNALS ARE BOTH BLINKING WHEN I HIT THE BRAKES

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 21 Answers

I bet you swapped the turn signal and brake lights cable.

Posted on Oct 21, 2013

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 302 Answers

SOURCE: picture wiring diagram for 2003 harley fatboy

May I suggest a trip to your local library. Cycle repair books should be in 646 stacks of reference.
Otherwise you can Google for 2003 Clymer Service manuals on the internet.
I think Clymer had electrical diagrams in their books. I doubt that any except the HD service book would have anything about the physical location of the harness, but the pictures in the other books would help you.

Posted on Oct 11, 2009

wd4ity
  • 4565 Answers

SOURCE: harley 1998 ultra wiring schematic

Sorry but I don't have a wiring diagram that I can send you but I may can offer a bit of help.

Your passing lamps are simply wired into a hot circuit somewhere. A lot of schematics don't show them because they are considered "add ons". They also may have a fuse inline with the "hot" wire. They have only one wire that connects them to the bike with the rest being inside the "light bar" itself. Find the wire coming out of the center of the "light bar" and trace it back to where it hooks up. Sorry but that's the best I can do on this one.

On your front brake light, there is a switch located inside your right hand switch housing where your throttle is located. It is a plunger type switch that is activated when you pull the front brake lever. A simple test of the switch is to loosen the bolts of the master cylinder and slide it towards the center of the handlebars. If the switch is good, the brake light will come on. If the switch is bad, it will not.

To get to the switch, you'll have to take the right hand switch housing apart. First, loosen the throttle cables at the adjusters and then remove the two bolts that hold the switch housing halves together. Carefully open up the switch housing. You will see the small switch in the front of the housing. You'll have to desolder the wires, replace the switch with a new one, and resolder the wires to the new switch.

Reassembly is the reverse of the disassembly. Make sure you slide the master cylinder all the way back against the switch housing or the brake light will stay on constantly. Readjust the throttle cables and check for proper operation. You don't want your throttle sticking.

Good Luck
Steve

Posted on Jun 15, 2010

wd4ity
  • 4565 Answers

SOURCE: 1974 Harley Davidson SPORTSTER TURN SIGNAL WIRING

I can help you with the wiring diagram but it will be the complete diagram. I have never seen just a turn signal only type wiring diagram. But, there's nothing to a '74 model Ironhead turn signal system.

All the wires for the system were gray but had these little "colored rubber bands" on the ends of the wires near the signal lights. The violet bands were for the left side and the brown bands were for the right side turn signals

Now, I cannot send the wiring diagram through this forum as it will not allow for an attachment. If you will contact me directly, I'll send you a wiring diagram as a jpeg attachment via e-mail. My address is wd4ity@bellsouth.net.

Good luck
Steve

Posted on Aug 22, 2010

wd4ity
  • 4565 Answers

SOURCE: i have a 2000 roadking.

To begin with, there is no relay for the brake light. That thing you hear clicking is a circuit breaker. You probably have a short circuit between the rear brake light switch underneath the bike and the brake light itself. If the tail lights work, then you know what circuit is ok.

Look at your rear brake master cylinder. Find the metal line coming out of it going to the rear of the bike. In that line, under the bike, you'll find a pressure switch. This is the rear brake light switch. The front brake light switch is located in the right side handlebar switch housing. If neither switch works the brake light, odds are you have a short circuit in the wiring from the rear brake light switch to the rear brake light itself.

Good Luck
Steve

Posted on Feb 26, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2000 dyna fxdl and the rear blinker is lighted all the time and dose not flash and when u hit brake light it acts like a brake light and the left front blinker wont flash


Hi Anonymous, check your wiring and connections from the turn signal switch to the turn signal module with a testlite. Make sure all connector pins are corroded, broken, or loose. For a free wiring diagram please visit the website below:
Good luck
Harley Davidson Wiring Diagrams and Schematics

Feb 05, 2014 | 2000 Harley Davidson FXDL Dyna Low Rider

1 Answer

Horn,turn signals lights dont work


Hi Anonymous, always check fuses and bulbs first. This all points to the left handlebar switch control housing open it up and check for damaged, cut, or pinched wires, check continuity on all switches. For a free wiring diagram please visit the website below and good luck. Harley Davidson Wiring Diagrams and Schematics

Jun 22, 2013 | 2000 Harley Davidson FXD Dyna Super Glide

1 Answer

2005 harley rr turn signal only works with brake applied


Hi Anonymous, always check fuses and bulbs first, you could have a faulty turn signal module or a bad turn signal button/switch, remove it from the switch housing and check for continuity, check your wiring and connections from the turn signal switch to the turn signal module with a testlite. Make sure all wires are not worn or pinched and connector pins are not corroded, broken, or loose. For a free wiring diagram please visit the website below:
Harley Davidson Wiring Diagrams and Schematics

Sep 10, 2012 | 2005 Harley Davidson FLHTCUI Electra Glide...

1 Answer

1989 FXST harley davidson turn signal problem


Hi Jun_gar, you could have a faulty module, check your wiring and connections from the turn signal switch to the turn signal module with a testlite. Make sure all wires are not worn or pinched and connector pins are not corroded, broken, or loose. For a free wiring diagram please visit the website below.
Harley Davidson Wiring Diagrams and Schematics

Jun 03, 2012 | 2000 Harley Davidson FXSTD Softail Duece

1 Answer

My turn signals and brake light won't work? It's a


Hi Hd84softail, always check fuses and bulbs first, you could have a faulty turn signal module or a bad turn signal button/switch, remove it from the switch housing and check for continuity, check your wiring and connections from the turn signal switch to the turn signal module with a testlite. Make sure all wires are not worn or pinched and connector pins are not corroded, broken, or loose. For a free wiring diagram please visit the website below: Harley Davidson Wiring Diagrams and Schematics

Apr 30, 2012 | 2000 Harley Davidson FXST Softail Standard

1 Answer

Turn signal schematic for 2000 hd softail


Hi Jason, for a free wiring diagram please visit the website below and good luck. Harley Davidson Wiring Diagrams and Schematics

Nov 19, 2011 | 2000 Harley Davidson FXST Softail Standard

1 Answer

2001 fxst harley brake light stays on all the time


Loosen the two bolts that holds the front brake master cylinder on to the handlebars and slide the front brake master cylinder down as close to the right handlebar switch housing as possible. If this does not solve the problem, I'd guess that the front brake light switch was bad and needs replacing. It's inside the right handlebar swich housing.

Good Luck
Steve

Jul 24, 2010 | 2000 Harley Davidson FLHR-FLHRI Road king

1 Answer

2000 FXST HARLEY engine light blinks on and off,speedo drops off while running, engine does not stop running,also notice that blinker stays on


Hi Nofkbed, always check fuses and bulbs first, you could have a faulty turn signal module or a bad turn signal button/switch, remove it from the switch housing and check for continuity, check your wiring and connections from the turn signal switch to the turn signal module with a testlite. Make sure all wires are not worn or pinched and connector pins are not corroded, broken, or loose. For a free wiring diagram please visit the website below: Harley Davidson Wiring Diagrams and Schematics Big Twin Carb EFI DTC Intructions codes Harley Davidson Forums Harley...

Jun 30, 2010 | 2000 Harley Davidson FXST Softail Standard

Not finding what you are looking for?
2000 Harley Davidson FXSTS Springer Softail Logo

303 people viewed this question

Ask a Question

Usually answered in minutes!

Top Harley Davidson Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Gills Lango

Level 2 Expert

195 Answers

Mike

Level 3 Expert

4336 Answers

Are you a Harley Davidson Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...