Question about kawasaki Motorcycles

Open Question

2002 2510 kawasaki mule engine will not turn over new batt tried to jump the relay very weak spark

Posted by on

4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 25 Answers

SOURCE: Kawasaki Mule 3010, keeps getting flat battery, wont jump start

Sometimes when the battery keeps going dead like that, a component may be creating a current draw. you can do a simple current draw test with a fluke meter by setting the meter to read amps, make sure the test leads are in the proper portals on the fluke for an amp test, and disconnect one of the battery cables and connect the test leads in-line with the battery and cable. It would help to know you have a good fuse inside the fluke. They are easy to blow, and whatever you do, DO NOT try to start the unit with the meter hooked up for the amp draw test. That is how fuses are blown. With the key off, check for any amp draw. If there is, you can start unplugging components until the draw goes away. If there was no draw to begin with, you may have a stator coil (or alternantor, whichever it has) that is weak and can't keep up.

Posted on Jun 11, 2009

  • 2 Answers

SOURCE: 1999 kawasaki mule will not

the problem might be a cdi box or stater or might be a rectifire/regulator

Posted on Jun 25, 2011

  • 1 Answer

SOURCE: engine wont turn over when start button is pushed

i posted a question bout my 93 almost the same prob i added a push button directly to selinoid an now mine start but i gotta use both buttons to start it. but just using one button i get no spark

Posted on Apr 11, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to adjust valves on a kawasaki mule 4010 trans

You must have a mark on the main crank shaft, and take the spark plug out, slowly and manually turn the crank shaft, put screw driver inside the spark plug hole and screw driver will raise and when stop and then go low turn back that your tdc

Aug 21, 2014 | Kawasaki Mule 4010 Trans Full Cab...

1 Answer

Kawasaki problems

it can be a few things it can be a bad solonid, bad connection, bad battery, or your starter needs new brushes

Jul 23, 2014 | kawasaki 2010 Mule 600

1 Answer

Why is #1cylinder spark weak on 2005 Kawasaki mule

All batteries decline in power with usage, or through a meachanical or chemical failure. If power from one cell is significantly lower than all the rest, it sounds like it will need replacing - the whole battery that is!

May 20, 2014 | 2003-2007 Kawasaki Kaf620 Mule 3010 4x4...

1 Answer

2012 kawasaki mule 4010 hitting on front cylinder only

First is the engine Diesel or Gas?
if it is a diesel engine it has almost got to be a compression or fuel problem if it is a Gas engine it can be a valve adjustment, fuel, compression, or spark problem

May 16, 2014 | kawasaki 2012 Mule 4010 4x4

1 Answer

Where is spark plug located on 550 kawasaki mule

on engine head it will looks like want to pull the socket first...

Feb 08, 2014 | All Years Kawasaki Kaf300 Mule 500 520 550...

1 Answer

Kawasaki mule 3010 won't do right and left signals when i press them, how to switch fuse for them?

Identify the fuse responsable for turn signals, extract it and insert another one with the same value in it's place.
Also could be turn's signals relay fault.

Oct 20, 2013 | kawasaki 2008 Mule 3010 4x4 Diesel

1 Answer

Changed the batt in a 2510 mule now it will not turn over the relay is working

hi if you changed the batt and relay is working check startermotor is turning and check the wires are tight if this is ok then check you coils and ht /plug caps are ok because if weak spark also check sparkplug is fitting ok or check for short circuit on the electrics hope you find out why this has happend

Oct 17, 2013 | kawasaki Motorcycles

1 Answer

My Kawasaki mule 550 clicks and the starter wont turn over. it has a new battery and selonoid.

It could be a relay clicking. Check with the parts department to find out if it `has one.

Oct 13, 2013 | All Years Kawasaki Kaf300 Mule 500 520 550...

1 Answer

My Kawasaki mule 3010 doesn't do anything when key is turned. I have changed the starter and relay. I have 12V at starter and all fuses are good. Horn and lights work. Any help?

Even if the relay under the seat makes a click when you turn the key, it can still be bad. Try jumping the hot leads and see if it cranks.

Oct 27, 2011 | Motorcycles

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

108 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers


Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides