Question about Aprilia RS 125 Motorcycles

1 Answer

My Aprilia doesn't go up 8000rpm on idle and when on gear 5000rpm I have changed the needle, idle and main jets on carburetor About the weather in here it is about 0-5C (32-41F) so should i put the bike on winter storage?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Aprilia Master
  • 43,005 Answers

Hi Atte_pekka, you may have a faulty high output coil and for this situation I would call my local dealer or reputable shop's service/parts department and inquire about any possible quick fix/test or parts inquiry. If necessary transport your vehicle to the dealer or shop and have a professional technician take it for a test drive, if it is in running condition, and give you a written estimate of repairs and answer any specific questions you may have about your issue. For more information about your issue please visit the website below. Good luck and have a nice day. DOWNLOAD Aprilia Rs 125

Posted on Oct 22, 2015

Ad

4 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get 2 Free calls (no credit card required) and instant help on almost anything you can think of (from cars to computers, appliances, handyman, and even pets).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 23 Answers

SOURCE: GSXR 750 Slingshot wont rev past 5000rpm, with or without choke

I have seen this before a few things to do too make sure. First take the air filter out and shine a light use your fingers to move the slides up and down I suspect the springs that go on the slide is not seated in center you can tell from the slide going halfway and hanging up. Next, the boots on the slides only go on 1 way there is a notch on the carbs for them. I would guess this would fix you up if not we can get deeper into it with air-fuel mix screw settings.good luck

Posted on Mar 25, 2009

BearWeb
  • 357 Answers

SOURCE: Yamaha 2002 TTr 250

Hi hoeygatt

Look around your bike near where the throttle cable meets the engine, when you pull the throttle, the cable pulls a quarter circle piece of metal which is connected to a spring, then connected to that should be a screw, that is the idle screw, turn it very slightly, usually clockwise to make the idle higher, and this should sort out the problem.

Please remember to rate this solution as FixYa!

Kind regards
BearWeb

Posted on Apr 12, 2009

  • 5 Answers

SOURCE: aprilia rs 125 2003 wont rev past 5000rpm in first or second

check the rev limmiter

Posted on May 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i lower the throttle pin on 2001 ktm 300 exc


if you need you bike jetted for 7000, take it to a shop and have it jetted.
If you dont understand your carburetor and make the wrong adjustment you can lean out and blow up the engine.
when you jet a bike for 7000, you need to change everything, main jet, idle jet, idle mixture, idle, and needle position.

Apr 15, 2013 | 2001 KTM EXC 300

1 Answer

Runs for a while then starts spluttering


Hi, Anonymous and the usual suspects are:
1. Idle speed improperly adjusted.
2. Inlet system air leak.
3. Damaged or restricted fuel tank venting system.
4. Dirty or damaged air cleaner element.
5. The accelerator pump is inoperative.
6. Vacuum piston assembly malfunction.
7. Enrichner valve is not seated or leaking.
8. Restricted fuel supply tract.
9. Plugged bowl vent.
10. Loose or plugged fuel and air jets or passages.
11. Improper fuel level.
12. Worn or damaged needle or needle jet.
13. Loose or plugged main jets or passages.
For more information about your issue please visit the websites below. Good luck and have a nice day.
DOWNLOAD 2007 Aprilia Sportcity 250

Mar 20, 2013 | 2007 Aprilia Sportcity 250

1 Answer

Aprilia rx 50 poor running


Hi, Anonymous and the usual suspects are:
1. Idle speed improperly adjusted.
2. Inlet system air leak.
3. Damaged or restricted fuel tank venting system.
4. Dirty or damaged air cleaner element.
5. The accelerator pump is inoperative.
6. Vacuum piston assembly malfunction.
7. Enrichner valve is not seated or leaking.
8. Restricted fuel supply tract.
9. Plugged bowl vent.
10. Loose or plugged fuel and air jets or passages.
11. Improper fuel level.
12. Worn or damaged needle or needle jet.
13. Loose or plugged main jets or passages.
For more information about your issue please visit the websites below. Good luck and have a nice day.
DOWNLOAD 2010 Aprilia Rx 50

Jan 14, 2013 | 2010 Aprilia RX 50

1 Answer

Wont start


Instructions
    • 1 Remove the seat by unscrewing the bolts found on the four corners of the seat. Remove the clamps from the top of the air box using a pair of pliers to access and remove the air filter. The air filter is removed by unscrewing the wing nut and sliding the filter out of the box. Loosen the hose clamp that connects the carburetor to the intake manifold, using a screwdriver.
    • 2 Loosen the fuel delivery hose clamp with a screwdriver and pull the carburetor out of the Blaster. Before troubleshooting the carburetor, it's important to note whether you've made a significant change in altitude or a change in your exhaust/intake setup. If you've made an altitude change, installed an aftermarket exhaust pipe or modified your air box, the jets will need to be changed. Refer to your manual for specific re-jetting instructions based on your altitude. Your exhaust kit will provide a recommended jetting setup. Do-it-yourself modifications like removing an air box will require you to experiment with the jet setup until you find the right one.
    • 3 Disassemble the carburetor by unscrewing the bowl screws from the bottom of the carburetor. With the bowl removed, the float, pilot jet and main jet will be exposed. To remove the pilot and main jet, unscrew them from their respective holes. The main jet will sit in the exact center of the bowl, while the smaller pilot jet will be set just below the main jet.
      Use a blunt object like a stick or rod to push the bottom of the needle receiver assembly out of the carburetor. The needle receiver (which houses the needle jet) will slide out of the top of the carburetor along with the slide, spring, carburetor cap and gasket. The carburetor is now completely disassembled and ready to be inspected.
    • 4 Inspect the pilot jet for blockage, slide a thin wire through the pilot jet's hole, spray it with carburetor spray and blow the center hole with compressed air. Repeat this process with the main jet. If there is any blockage or wear, replace the jets. If you have made altitude changes or exhaust/intake modifications, insert jets that correspond to your changes as recommended in your manual. Note that this may take some experimentation with different jets to get the correct jet setup, as there are many jet sizes for different scenarios.
    • 5 Inspect the bowl, floats and ports for any signs of debris or gunk. If debris or gunk is found, remove it using a spray carburetor cleaner, soft wire brush, or thin wire (to insert into small orifices). If no gunk or debris is found, you've ruled this out as a possible cause for the starting issues, and can focus on the replacement of carburetor components.
    • 6 Look for abnormal wearing on the jets, float valve, gaskets, O-rings and springs. If you have not changed altitude or modified your bike in any way, then it is best to inspect these components. Any one of these components, or a combination, may be contributing to your starting issues. You may choose to replace individual parts such as a new float valve, though replacing all the interior components with a carburetor "rebuild kit" is advised. Rebuild kits can be ordered online or through your dealer, and will ensure your carburetor is fully repaired.
    • 7 Slide the gasket, spring, spring holder and needle jet assembly back onto the carburetor cap and insert the assembly into the top of the carburetor. Screw the main jet into the bottom of the needle jet assembly by accessing it through the bowl area. Screw the pilot jet back into its hole below the main jet. Clip the float valve onto its hinge within the bowl a insert the bowl gasket. Screw the bowl to the bottom of the carburetor to complete the re-assembly process.
    • 8 Re-attach the carburetor to the intake manifold using the hose clamp and screwdriver. Slide the fuel feeder line onto the brass receiver port on the side of the carburetor and slide the air box boot over the carburetor's intake port, which should be facing toward the back of the bike. Re-install the air filter with its wing nut, slide the clips over the air box top to secure it to the box and slide the seat into place. Re-install the seat screws to complete the re-assembly process.
    • 9 Prime the carburetor by twisting the throttle once and start the Blaster.

Jan 14, 2013 | Yamaha V Star 1100 Custom Motorcycles

1 Answer

1992 Suzuki GSF 400 Bandit carburetor jetting


Hi, Crazystang79 if you have changed your fuel delivery system, air filter size or flow rate, mufflers or exhaust system or a significant change in altitude your carburetors need re-tuning and if your fuel system (gas tank, filters, fuel valve and carburetor) is contaminated with ethanol sludge, varnish, rust, dirt, water etc. or your bike has been sitting for months or years without running these components must be "PROPERLY" cleaned and reassembled "CORRECTLY" before any adjustments can be made. Tuning your carburetor is fairly simple once you understand the basic principals. You engine is a simple airbox sucking air in and blowing it out, it is finely tuned at the factory for maximum performance once you upset that delicate balance by changing air filters, camshafts or exhaust systems your performance may go down the and the engine may run poorly, you need to compensate the air-fuel mixture in the carburetor in order for the engine to run smoothly and at peak performance. If you are running multi carburetors you need to sync them first and make sure your air cleaner element is clean and dry for paper elements or lightly oiled for foam and meshed elements and properly installed. Here is how and where you compensate trouble: "TIP" if your engine "BOGS" your not getting enough fuel.
1. Closed to 1/8 throttle is managed by the air screw and pilot/slow jet.
2. 1/8 to 1/4 throttle is managed by the air-screw, pilot/slow jet, and throttle slide.
3. 1/4 to 1/2 throttle is managed by the throttle slide and jet needle.
4. 1/2 to 3/4 throttle is managed by the jet needle, needle jet, main jet, and air jet.
5. 3/4 to wide open throttle is managed by the main jet and air jet.
6. Wide open throttle is managed by the main jet.
If you are running lean, spark plug electrode color is white, engine runs hot and feels like it is starving for fuel you need to go up on the jet size or move the c-clip down one notch. If you are running rich, spark plug color is black or dark gray, engine runs cool, and bogs down when accelerating you need to go down on jet size or move the c-clip up one notch. When your carburetor is properly tuned for maximum performance your spark plug electrode will be a light tan color like coffee with cream. If you prefer fuel economy over performance you can go down on main jet sizes until a satisfactory level of lower performance is acceptable versus MPH, your spark plug color will be whiter and your engine will run warmer. These tuning adjustments will only make improvements if your intake and exhaust system have no air leaks or sealing issues and the entire electrical system is in proper working order and you have no mechanical issues.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Carb Rebuilding Needle Jets Jet Needles etc
Carburator Theory and Tuning
Suzuki GSF 400 BANDIT Service Manual
OEM parts for Suzuki
http://mybikemanuals.com/suzuki

May 17, 2017 | 1992 Suzuki GSF 400 Bandit

1 Answer

1982 Yamaha XJ750 Maxim will not idle


Hi, Davehougen6 if you have changed your fuel delivery system, air filter size or flow rate, mufflers or exhaust system or a significant change in altitude your carburetors need re-tuning and if your fuel system (gas tank, filters, fuel valve and carburetor) is contaminated with ethanol sludge, varnish, rust, dirt, water etc. or your bike has been sitting for months or years without running these components must be "PROPERLY" cleaned and reassembled "CORRECTLY" before any adjustments can be made. Tuning your carburetor is fairly simple once you understand the basic principals. You engine is a simple airbox sucking air in and blowing it out, it is finely tuned at the factory for maximum performance once you upset that delicate balance by changing air filters, camshafts or exhaust systems your performance may go down the and the engine may run poorly, you need to compensate the air-fuel mixture in the carburetor in order for the engine to run smoothly and at peak performance. If you are running multi carburetors you need to sync them first and make sure your air cleaner element is clean and dry for paper elements or lightly oiled for foam and meshed elements and properly installed. Here is how and where you compensate trouble: "TIP" if your engine "BOGS" your not getting enough fuel.
1. Closed to 1/8 throttle is managed by the air screw and pilot/slow jet.
2. 1/8 to 1/4 throttle is managed by the air-screw, pilot/slow jet, and throttle slide.
3. 1/4 to 1/2 throttle is managed by the throttle slide and jet needle.
4. 1/2 to 3/4 throttle is managed by the jet needle, needle jet, main jet, and air jet.
5. 3/4 to wide open throttle is managed by the main jet and air jet.
6. Wide open throttle is managed by the main jet.
If you are running lean, spark plug electrode color is white, engine runs hot and feels like it is starving for fuel you need to go up on the jet size or move the c-clip down one notch. If you are running rich, spark plug color is black or dark gray, the engine runs cool, and bogs down when accelerating you need to go down on jet size or move the c-clip up one notch. When your carburetor is properly tuned for maximum performance your spark plug electrode will be a light tan color like coffee with cream. If you prefer fuel economy over performance you can go down on main jet sizes until a satisfactory level of lower performance is acceptable versus MPH, your spark plug color will be whiter and your engine will run warmer. These tuning adjustments will only make improvements if your intake and exhaust system have no air leaks or sealing issues and the entire electrical system is in proper working order and you have no mechanical issues.
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
Life On 2 Wheels
Carburator Theory and Tuning
Yamaha XJ750 Owner Manual Typo actually a service manual
OEM parts for Yamaha
http://mybikemanuals.com/yamaha/yamaha-xj-owners-manuals

Jan 29, 2011 | Yamaha Motorcycles

2 Answers

Will ethanol in 93 octane cause the coughing poping out of the air intake?


Not likely. You probably do have a plugged circuit in the carburetor though. Remove the carb and clean. Pay special attention to the pilot and main jets and circuits. Blow out with carb cleaner and air. If you pull the idle mixture screw, (recommended, also, screw the idle mixture screw inwards counting the turns as you go before removing), be sure to remove the washer and "o" ring with the mixture screw, sometimes they will not come willingly. Clean the carburetor thoroughly, re-install idle mixture screw to number of turns out, (as you counted before removing), re-install carb on bike and test.

Nov 03, 2010 | 2000 Harley Davidson FLHR-FLHRI Road king

2 Answers

Yamaha 125 grizzly starts and idles when choked but dies when acc


check that reed valves not sticking and check the pilot jet its prob. half blocked. have to stick a very thin wire through it.

Aug 12, 2009 | 2003 Yamaha YZ 125

1 Answer

Flat spot from 5000rpm-6000rpm


it sounds like you have a blocked jet,pull the carbs out,remove the bowls and inspect /clean the fuel jets,be carefull not to overtighten the jets when you put them back in as they are only very thin brass and quite fragile..hope this helps

Jul 06, 2009 | 1998 Aprilia RS 125 Extrema

Not finding what you are looking for?
Motorcycles Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Aprilia Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4535 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you an Aprilia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...