Question about 1992 Suzuki GSX 600 F (Katana)

1 Answer

I have just replaced the petcock and now the engine will not start. There are two wires, one black and one yellow, that go to the fuel gauge. I know that yellow goes with yellow, but where does the black one go? The engine will try to start, but it won't catch. what do i do?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 381 Answers

Hello,
Generally speaking on Suzuki's, the yellow wire is +12vdc and Black is a ground wire. You should connect it to the closest frame connection. It also might appear that you have another wiring problem in that same area due to the no start issue. Make sure all wires in the immediate area where you were working are connected properly and none were forgotten! You should verify that the gas does flow freely from your repair as that also could cause the start issue if no gas is flowing!

Posted on Nov 05, 2013

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My car is not starting and thinking it's the fuel pump. Try jumping it and still not go. Alternator and starter are fine. So I've removed the fuel pump from the tank. There's a white connector that...


Four wires the the sender unit. One will have 12 volts all the time with key on. This is the fuel gauge. One will have power for 2 seconds when the key is turned on. This is the fuel pump. Two of them will have a constant ground. Grounds will be black, black with a colored stripe on it, or have a black stripe. Check the harness plug plug for voltage, again it only last for 2 seconds. If you have voltage at the wire. replace the pump. If not, probe the wire about 3 inches back from the plug, check for voltage again. If you have voltage there repair or replace the plug. Most wires break right behind the harness plug.

Feb 14, 2015 | 2003 Toyota Corolla

1 Answer

Look the fuel pump is the gas tank of a 1996 ford


On most models the fuel pump wires are pink-black and black. The third wire is usually yellow and its for the gas gauge.

Sep 04, 2014 | Cars & Trucks

1 Answer

K my 2005flht harleydavidson gage quit working and only fuel gage I have power to it and light work


The fuel gauge sender is mounted internally in the fuel tank. There is a three pin connector that will have a Yellow/White wire in it (the middle wire) under the center console. This is the sender wire. Connect an ohm meter between this wire and the black wire and check for the following readings:
If fuel tank is full, the reading should be 7-14 ohms. An empty tank should have a 74-95 ohm resistance. A half full tank will be approximately 30-38 ohms.
If you ground this wire that comes from the harness, the fuel gauge should read full. If not, then fault may be in wiring or the fuel gauge itself.
Remove the front fairing to gain access to the gauge. You should have 12 volts across the orange/white and black wires. If not, check accessory fuse. If 12 volts present ground the yellow/white wire at the gauge. Gauge should read full scale. If not, gauge faulty. If gauge reads full scale, check wiring from gauge to three pin plug under tank console.

Jul 27, 2014 | Harley Davidson Motorcycles

1 Answer

My gas gage reads empty but stays lit up on 2005flht


The fuel gauge sender is mounted internally in the fuel tank. There is a three pin connector that will have a Yellow/White wire in it (the middle wire) under the center console. This is the sender wire. Connect an ohm meter between this wire and the black wire and check for the following readings:
If fuel tank is full, the reading should be 7-14 ohms. An empty tank should have a 74-95 ohm resistance. A half full tank will be approximately 30-38 ohms.
If you ground this wire that comes from the harness, the fuel gauge should read full. If not, then fault may be in wiring or the fuel gauge itself.
Remove the front fairing to gain access to the gauge. You should have 12 volts across the orange/white and black wires. If not, check accessory fuse. If 12 volts present ground the yellow/white wire at the gauge. Gauge should read full scale. If not, gauge faulty. If gauge reads full scale, check wiring from gauge to three pin plug under tank console.

Jul 27, 2014 | Harley Davidson Motorcycles

1 Answer

1990 gmc K1500 5.7L, temp. gauge not working:


To review, you have two temp sensors, one for the gauge on the dash and one for the computer. If you unplug the sensor for the computer the reading will be minus 30 degrees or over 300 which will make it very hard to start. Unplugging the sensor for the gauge would have no effect on the computer.
According to the wiring diagram, the wire for the temp gauge is green, and the wires for the temp sensor for the computer are yellow and black.

Aug 24, 2012 | 1990 GMC Sierra

1 Answer

Bike just quit, will not crank. I have gas and plenty of battery. I changed both plugs. I suspect no fire from the coil. But I;m not sure how to troubleshoot the coil.


Pull the spark plug wires off the spark plugs. Get another set of spark plugs and put them in the wires. Make sure the spark plugs are grounded to the engine, turn the switch on and press the start button. You should see the plugs spark as the engine turns over. On another note, if your bike is equipped with a carburetor, you may have fuel in the fuel tank but none in the carb. In 1996, Harley went to a vacuum operated fuel petcock and they give problems. The diaphragm in the backside of the petcock gets a hole in it and it will not open and allow fuel to flow to the carb. You can have a full fuel tank but not a drop of fuel in the carb. The petcock can be repaired but you'll have to drain the fuel tank and remove the petcock. I usually suggest that the petcock be replaced with a high quality manually operated petcock like a PIngel. You'll have to manually turn your fuel on and off old school style but you'll solve that problem permanently.

Good Luck
steve

Jun 10, 2011 | Harley Davidson FLSTS Heritage Springer...

1 Answer

While driving motorcycle stalled.


Sounds like you've lost either spark or fuel. Take another set of spark plugs and plug them into your spark plug wires. Do not remove the plugs from the head. Spin the engine and watch for spark. If no spark, first check the "run/start" switch. If it's alright, you need to check the fuse for you ignition system to see if it's blown.

On fuel injected engines, you have a fuel pump. Check the fuse for the fuel pump. Listen for the fuel pump to run when the switch is turned on.

If you bike is carburated, check the petcock. In 1996, H-D went to a vacuum operated fuel petcock. These things are notorious for giving problems. Either the diaphragm gets a hole in it and shuts off the fuel or the vacuum hose comes loose. Check the vacuum hose that comes off the back of the carburetor and runs to the VOES switch and the petcock. You may have to remove the petcock to service the diphragm in it.

If you remove the petcock, there are four small bolts on the backside. Remove the four bolts, lift the plate and theres a spring and a diaphragm behind the plate. Check the diaphragm for holes. If you find hole, replace the diaphragm. If not, replace everything and test the petcock by applying vacuum to the rear of the petcock while blowing though the fuel line nipple. When you appy the vacuum, the petcock should be open. With no vacuum, petcock should be closed. Good Luck, Steve

Apr 27, 2010 | 2004 Harley Davidson FLTRI Road Glide

1 Answer

Bike won't start


Start by narrowing it down to fire or fuel problem. Pull a sparkplug, ground it to the head, and crank the engine. If there is no spark, then test the plug wires, coil, then ignition module in order down the line until you find where the power stops. If you have spark, then check the petcock to carb for fuel. If there is no fuel from the petcock, then it will be the petcock filter or the petcock is bad. If you do have fuel to the carb, but no to the cylinders, then the carb may need to be cleaned and/or rebuilt. Try these and let me know.

Aug 19, 2008 | Harley Davidson Harley-Davidson Motorcycle...

Not finding what you are looking for?
1992 Suzuki GSX 600 F (Katana) Logo

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

Ed Nelson
Ed Nelson

Level 2 Expert

149 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...