Rear wheel bearings on Hyundai Accent

The easy way is to go to the dealership parts department. They would keep those in stock. Or you go to a spares motor factor like the ones below. They are picking up 'wheel bearings', but they can supply all bearing parts..

Wheel bearing for HYUNDAI Coupe II (GK) - Buycarparts.co.uk

https://www.buycarparts.co.uk > ... > COUPE (GK)
Hub bearing for HYUNDAI Coupe II (GK) Petrol / 1.6 - 2.7 liters / 2001 - 2009 MY ... G4GC 02/2003 - 08/2009; 2.7 V6 (121 kW / 165 hp) G6BA 01/2001 - 08/2009 ...
Missing: manual ‎' Must include: manual

• 
  

  Wheel bearing for HYUNDAI COUPE - Buycarparts.co.uk

  https://www.buycarparts.co.uk > ... > COUPE
  Couldn't find your car in the catalogue? or. Enter your registration below. GB. Search ...

Wheel bearing for Hyundai Coupe gk - AUTODOC

https://www.autodoc.co.uk > ... > HYUNDAI > COUPE
Wheel bearing rear and front for HYUNDAI COUPE (GK) from 2001 MY from various OEM part manufacturers. Huge brand selection at low prices ? Hub bearing for ...
Missing: litre ‎output

• 
  

  Car parts & accessories for HYUNDAI COUPE - AUTODOC

  https://www.autodoc.co.uk > spares > hyundai > coupe
  Over 5000 car parts for HYUNDAI COUPE found in stock at AUTODOC ? Purchase vehicle parts ? auto accessories for HYUNDAI COUPE online at affordable prices ...

Transmission output shaft bearing. - Hyundai - JustAnswer

https://www.justanswer.com > hyundai > 94h1d-transmi...
Jun. 3, 2015 - Transmission output shaft bearing. problem. Our 2005 Hyundai Accent stick shift. Parts errand car. Replaced CV - Answered by a verified ...
1 answer · Top answer: See the answer on the image
Missing: reg ‎' Must include: reg

Yes, Undo the 32mm nut, first. And, don't get the bearings dirty with dust from the brake drums, or , if you do, replace the inner and outer bearings with new greased up ones. REAR DRUM BRAKES Brake Drums REMOVAL & INSTALLATION CAUTION
Brake linings contain asbestos. Asbestos is a known cancer-causing agent. When working on brakes, remember that the dust which accumulates on the brake parts and/or in the drum contains asbestos. Always wear a protective face covering, such as a painter's mask, when working on the brakes. NEVER blow the dust from the brakes or drum.

1. Raise the vehicle and support safely.
2. Remove the wheel and tire assembly.
3. On vehicles without rear bearing hub, remove the dust cap, cotter pin, nut lock, wheel bearing nut and washer from the spindle. Remove the outer wheel bearing. Remove the drum with the inner wheel bearing from the spindle. If the drum is difficult to remove, remove the plug from the rear of the backing plate and push the self adjuster lever away from the star wheel. Rotate the star wheel to retract the shoes. Remove the grease seal.
4. If equipped with a rear bearing hub, remove the drum by removing the retainer screws from the drum and pulling the drum from the hub assembly. If the drum is difficult to remove, remove the plug from the rear of the backing plate and push the self adjuster lever away from the star wheel. Rotate the star wheel to retract the shoes. To install:
   
5. On vehicles equipped without rear bearing hub, lubricate and install the inner wheel bearing. Install a new grease seal. Install the drum to the spindle. Lubricate and install the outer wheel bearing, washer and nut. Adjust the bearing preload following the procedure outlined in the "Rear Wheel Bearing'' of this section. When the bearing preload is properly set, install the nut lock and a new cotter pin. Install the grease cap.
6. On vehicles with rear bearing hub, install the brake drum to the hub assembly and install the retaining screws.
7. Install the wheel and tire assembly. Adjust the rear brakes as required.
8. Apply the brakes until a firm pedal is obtained, prior to moving the vehicle.

With Rear Hub Bearing

1. Raise the vehicle and support safely.
   
2. Remove the wheels.
   
3. Remove the dust cap, cotter pin and loosen the locknut
   
4. Remove the washer and outer wheel bearing.
   

If the drum is difficult to remove, remove the plug from the rear of the backing plate and push the self adjuster lever away from the star wheel. Rotate the star wheel to retract the shoes.

1. Remove the drum with the inner wheel bearing from the spindle.
   

To install:

1. Install the drum on the spindle.
   
2. Install the outer wheel bearing and washer.
   
3. Tighten the locknut to 108-145 ft. lbs. (150-200 Nm). Turn the brake drum while tightening the spindle nut to seat the wheel bearings.
   
4. Install the cotter pin and dust cap.
   
5. Install the wheels
   
6. Adjust the rear brakes.
   

hi from uk to remove rear hub/s you have to remove the bolts that secure the hub and brake backplate to th axle these hubs come complete with bearing and is not normally the case of replacing the actual bearing ? and this type of hub is becoming common fitting on lots of vehicles like hyundai/ford/vauxhall etc hope this helps ?

it could be problem with any sensor of abs of any wheel, it as not a major problem , dont worry check with technician.

just remove the wheel and count the teeth on the ring on the rear brake thats all you need to do. Since you can't drive it take it off and take it in to compare parts so you don't have to go back twice. You will need a new wheel seal and race and bearings.

drum brakes you remove rear wheel- speed sensor-grease cap-flange nut-outer bearing-brake drum-inner grease seal-inner bearing-drive the bearing races out of the drum hub.to install -install the inner and outer bearing races.apply grease to the bearings and hub cavity.then you install the inner bearing -inner grease seal-brake drum-outer bearing-flange nut torque it to 159 to 192 ft lbs. THE REAR DISC BRAKE WHEEL BEARINGS-you have to remove rear wheel -wheel speed sensor-brake caliper and rotor-rear axle hub bolts-tone the wheel with tool 09445-21000-carrier assembly-nut after unstaking it-press out the rear axle hub-remove the bearing inner race with tool 09445-21000-remove the bushings from the carrier with tools 09453-33000b and 09545-21100.to install -press in the bushings to the carrier with tools 09453-33000b and 09545-21100- press in the bearings to the hub with tool 09221-21000.tighten the flange nut to meet the concave portion of the spindle-press in the tone wheel with tool 09221-21000-torque the nut to 191 ft lbs -install the hub and bearing assembly to the backing plate and torque the bolts to 88 ft lbs-install the brake caliper and rotor.install the wheel speed sensor if equipped.install the rear wheel.TO BUY THE TOOLS TO DO THE JOB.LOOK UP KENT MOORE TOOLS ON INTERNET.

REAR BRAKE NOISE - SHOE AND LINING KIT
A shoe and lining kit is available for installation if an Elantra (XD) or Accent (LC)
equipped with rear drum brakes exhibits a chattering noise from the rear brakes when
the brakes are applied.

APPLICABLE VEHICLES:
• Accent (LC) and Elantra (XD) equipped with rear drum brakes and in the following
Production Date and VIN Range:
SERVICE PROCEDURE:
For further information, refer to the applicable Shop Manual.
Model Production Date Range VIN Range
ACCENT (LC) May 21,1999 - Dec. 28, 2005 ALL WITH DRUM
BRAKES.
ELANTRA(XD) June 30, 2000 - May 23, 2006 JOB#1-
KMHDN46016V363974

ACCENT SHOE & LINING
KIT
ASSEMBLY
58305-25A00 58305-25F00 7"(00MY - 05MY)
58305-25A10 58305-25F10 8"(00MY - 05MY)

jack up the rear wheel and spin it, do this with the other wheels chocked for safety, and listen for any rubbing sound, do this with both rear wheels and if one is bad then remove the drum again to check if the retainer has come off of the brake lining, hope this helps you.

Ouch, get your wheel bearings checked. I had a 97 Hyundai and in the 3 years I had it, the front bearings had to be replaced twice and the rear once once.