Question about 2002 BMW R 1150 GS

1 Answer

Front abs brakes

I replaced the to brake pipes in the front and i have blead the brakes but the first push on the brake is spungy but the second push is hard and the abs light is flashing

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • BMW Master
  • 39,945 Answers

Hi, Anonymous I am sorry you can't find the first and best tool you ever bought for your BMW but despair not for a mere $0 you can download another one. For more information about your issue, please visit the websites below. Good luck and have a nice day.
How to bleed brakes on Motorcycle with ABS or after installing stainless...
BMW R1100RT Brake lines replacement line bleed
1999 2005 BMW R1150GS Service Manual Moto Data Project
BMW Motorcycle Parts Fiche OEM BMW Motorcycle Parts online 1970 present BMW
http://www.bmw-motorrad.com/us/en/index.html?content=http://www.bmw-motorrad.com/us/en/services/manuals/manuals_main.html¬rack=1

Posted on Dec 30, 2015

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

cape cod bob
  • 292 Answers

SOURCE: bleeding brakes on bmw k1200gt 2003

you can probably find out here http://www.carlsalter.com/motorcycle-manuals.asp for free pdf service manual

Posted on Apr 04, 2009

  • 1 Answer

SOURCE: ABS light flashs - push switch and it stays on completley

it is caused by low battery voltage run bike for about a mile then stop turn of turn back on wait till abs lights go out then start

Posted on Apr 14, 2009

  • 375 Answers

SOURCE: abs fault on 2004 r1150rt

I would take it in to get the ABS system serviced - you may have introduced air into the hydraulics or moved the ABS sensor out of position. If oyu have the power-assist brakes, you will notice that there isn't any - assist, that is.

Posted on Jul 03, 2009

Adrian762
  • 425 Answers

SOURCE: I have a 2000 BMW R 1100 RT (ABS). The front brake

Because the fluid services both side evenly, you should only need to bleed the LHS. Just bleed it the same as you would a normal hydraulic system.

Put a small piece of plastic tubing over the bleeder valve, and make it as airtight as possible, I generally lock it with a piece of brass wire.
Place this into a jar with enough brake fluid to cover the bottom of the tube. Open the reservoir, it is easier with two people, open the bleeder valve, and pump like carzy, adding more fluid to the reservoir as required until no bubbles appear in the jar. Then lock off the bleeder valve and clean up the mess, after re-fitting the reservoir cover.

Posted on Feb 17, 2010

  • 4 Answers

SOURCE: ABS failure on 04 R1200C Montauk, very limited braking ability

check brake fluid levels and also, believe it or not, the brake light bulb.

Posted on Jul 04, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What is the proper way to bleed the brakes on this bike with ABS?


Hi,I had a yamaha fj1200 that had abs and when bleading the brakes I just blead the brakes in the normal way,I found that it makes it easyer to blead,open resouveor cap and top up and put a rag around the resouvor to protect any paintwork then get a bungie tie and slowly pump the brake lever slowly as not to creat lots of air bubbles in the system,then rap the bungie around the lever and handle bar to keep the lever pulled in,then go to the back caliper and put the tube in a glass and fill with brake fluid untill it covers the end of the tube,put the other end on the blead nipple a slowly open the nipple just so you can see the fluid coming out,when it stops flowing tighten the blead nipple and do this again untill all the air is out and you have clean fluid coming through,the do the same to the front,job done.
there is a self bleading tube with a valve on the end so that the air dose not go back in the system,there is also a brake bleading system on the market that is a self bleading system where you have tube that connects to the resouvor with its own lid, and a tube that runs from that to a bottle which you put the brake fluid in,and a tube runs from that to a connector like the one that is on a foot pump,that connects to a wheel wich supplies the presure to push the fluid through the system,so with this system all you have to do is open the blead nipple and lock it again when done.
I hope this was some help.
Ive explaned it becouse not every one knows how to do this,so sorry if im telling you how to suck eggs.

Apr 17, 2015 | Ducati Motorcycles

1 Answer

Replaced the brake line on the front of a silverado but now the back brakes don't work


you have to do an automated bleed with a scan tool.There is a section in the scan tool to do such a task.

Jan 15, 2014 | 2000 Chevrolet Silverado 1500

1 Answer

Abs engages on routine stops, brake pedal low and stopping distance seems greater.


Sounds like you might have a bad ABS pump.
Or you can try and adjust the rear brakes.
And if it is just the ABS pump. You do not have to worried about not having brakes. The only thing you will not have is the sliding control or skidding control.
And that means in a panic stop all your tries will lock up

Nov 16, 2012 | Ford Vehicle Parts & Accessories

1 Answer

Spungy brakes


Car over heated the heater tubing was broke its was fixed put water in the radader and the water is going some where

Jan 17, 2012 | 1995 Honda Accord

1 Answer

I have a 96 ford explorer xlt 4wd with ABS. When I bought it it had a broken back break line. I replaced the line blead the breaks and the breaks are spongy. I googled the issuse and found out it could be...


Check your parking brake. if it goes down to the floor or does not hold, then your back brakes needs adjusted. bad master cylinders bleed off slowly to the floor while pushing on the brake pedal. If you need assistance on adjusting let me know.
Randy

Nov 09, 2010 | 1996 Ford Explorer

2 Answers

I relaced all brake pads on 2003 buick bleed brakes very little air my brake peddle still spungy and anti brake light stays on


you must re-bleed the system properly, especially the back brakes. Bring your vehicle to a local autozone to reset the ABS light or check for an ABS fault code and post it on fixya!!

Sep 27, 2010 | Buick Rendezvous Cars & Trucks

2 Answers

How can I tell if I have abs on my 1996 Dodge dakota the abs and brake light is on and the brakes got spungy.


seeing an abs light is a good clue that you have that feature. Additionally, you will have a far more elaborate set of brake lines and devices attached to the master cylinder than you see on a non-abs vehicle.

Jan 18, 2010 | 1996 Dodge Dakota

1 Answer

Fixing brakes


Try bleading the brakes, sounds like you have in them. Than the ABS light should go out & you shouldn't have to worry about the fuses.

Jun 02, 2009 | 1993 Plymouth Voyager

1 Answer

Can I replace a brake hose front and back on 95 escort easily???


Not a good idea, if vehichle has abs then you can't blead it properly and even if it did'nt without bleading system, air in lines can cause brake failure.

Apr 26, 2009 | 1995 Ford Escort

1 Answer

2000 chevy lunima rear brake line blew replaced brake line and bleed but anti-brake lite stays on


Chevys are bare to blead, especially if it has ABS. Chevy dealers actually use TECH 2 / their computer to blead ABS systems properly. With it, they open the ports in ABS module, which helps the brake fluid flow. Unless of course you have ripped the sensor wire for ABS by accident.

Jul 21, 2008 | Chevrolet Chevy Cars & Trucks

Not finding what you are looking for?
2002 BMW R 1150 GS Logo

Related Topics:

43 people viewed this question

Ask a Question

Usually answered in minutes!

Top BMW Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4514 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

phil cuzins
phil cuzins

Level 2 Expert

79 Answers

Are you a BMW Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...