Question about 1981 kawasaki Csr 1000

1 Answer

Battery not charging Is there a known problem with the stator or Regulator?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 11 Answers

I don't of specific problems with Kawa electrics. I assume you have checked the charge voltage across the battery. Get the engine running and measure the voltage at the battery terminals. The voltage should be between 13.5 & 14.5v with engine running. If your meter shows 12v, then the battery is not receiving a charge. I once had this problem on an old Suzi GT380. The fault was caused by an earth wire missing! Make sure the regulator and rectifier are earthed. Assuming all the above is ok then the stator may be burned out. recommend the Haynes Motorcycle Electrical Manual.

Posted on Apr 23, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 vl 1500 charging system system not charging checked generator 3 wires giving pluss 80v at 5000rpm instaled new rectifier voltage across battery under 13 volts could faulty battery be problem


Hi, Anonymous the following is a comprehensive charging system test that I found on a Rider Groups website
1. Battery Test: The battery needs to be a fully charged battery that has been load tested to ensure proper readings. If you are not working with a fully charged and functional battery, all other voltage tests will be incorrect. Most places like Auto Zone, Advance Auto, and Pep Boys will charge and test motorcycle batteries for free. Standing battery Voltage should be 12.5-13.2 DCV.
2. Charging System Voltage Test: Start motorcycle, Measure DC Volts across the battery terminals (you should have a reading of approximately 13.2-15 DC Volts).
3. Check Connections/Wires: Inspect the regulator/stator plug, and check the battery terminals for connection/corrosion. If everything seems to be in order, move on to number 4 below to determine if there's a failed component.
4. Stator Checks/Rotor Check: Each of the following tests isolate the stator & Rotor, If AC Output test Fails and Resistance Check, and Stator IB Test Pass then Rotor is at fault (Pull Primary covers and inspect rotor for damage).
AC Output Check:
Unplug the regulator plug from the stator
Start motorcycle and change Voltmeter to AC volts.
Probe both stator wires with your meter leads.
The motorcycle should be putting out approximately 18-20 ACV per 1,000 rpm. (Reading will vary depending on system, check service manual specification)
Generic Specs:
22 amp system produces about 19-26 VAC per 1,000 rpm
32 amp system produces about 16-20 VAC per 1,000 rpm
45 amp system produces about 19-26 VAC per 1,000 rpm
Stator Resistance Check:
Switch your multimeter to Ohm x 1 scale.
Probe each stator wires with meter leads and check resistance on the meter.
Resistance should be in the range of 0.1-0.5 Ohms. (Reading will vary depending on system, check service manual for specification)
Generic Specs:
22 amp system produces about 0.2 to 0.4 ohms
32 amp system produces about 0.1 to 0.2 ohms
45 amp system produces about 0.1 to 0.2 ohms
Stator IB test or Ground Check:
Switch your multimeter to Ohm x 1 scale.
Probe each stator wire with your positive lead on the multimeter and the negative to ground.
There should be no continuity to ground on either wire.
If there is continuity to ground your stator is shorted to ground.
5. Regulator Test: Each of the following tests isolates the regulator only, so if any of these tests fail, the regulator is at fault.
Identifying Wires:
Battery Charge Lead- Wire going from regulator to battery positive.
AC output leads- Wires coming from the Stator to the regulator.
Ground- Wire from Regulator to ground or regulator may be grounded via the physical bolting to chassis.
Regulator Ground Test: Ensure the regulator body is grounded or grounding wire is fastened tightly to a good ground (you should verify this by checking continuity from regulator body to chassis ground).
Fwd/Reverse Bias Test/Diode Test: This check is testing the Diode function to ensure it is regulating the AC current for the stator into DC Current.
Switch multimeter to Diode Scale.
Place your Multimeter positive lead on each AC output wire.
Place your multimeter negative lead on the battery Charge wire.
The meter should read voltage typically around .5 volts.
Next, switch your multimeter leads putting the negative lead on the AC output wires and the Positive lead on the Battery Charge Wire.
The reading should be Infinite.
With your meter on the same setting, place your multimeter positive lead on the regulator ground wire or to the regulator directly, and then place your meter negative lead on the AC output leads.
The meter should read voltage typically around .5 volts.
Next, switch your multimeter leads putting the negative lead on the regulator ground and the Positive lead on the AC output wires.
The reading should be Infinite.
Note: Below is a table to show the readings:
Positive Lead Negative Lead Reading
AC output 1 Battery charge lead Voltage
AC output 2 Battery Charge Lead Voltage
Battery charge lead AC output 1 ?
Battery charge lead AC output 2 ?
Ground AC output 1 Voltage
Ground AC output 2 Voltage
AC output 1 Ground ?
AC output 2 Ground ?
For more information about your issue and valuable "FREE" downloads that you will need please click on the links below. Good luck and have a nice day.
http://www.crowitis.com/images/VL1500_Charging_System_Wiring_Upgrades.pdf
stator output voltage
http://www.jetav8r.com/Vision/Stator/fault_finding_by_www.electrosport.com.pdf
Suzuki VL1500 Service Manual
OEM parts for Suzuki
Suzuki VZ1500 Owner Manual

Jan 16, 2017 | Motorcycles

1 Answer

Looking for help charging system not charging battery on 1999 Harley Davidson fatboy


Check regulator ground by using an ohmmeter with one lead on a known good ground, such as the battery ground cable, and the other on the regulator base.
The connection where the alternator stator wires plug into the regulator could be corroded/dirty and need to be cleaned and sprayed with electrical contact cleaner and protected with dielectric grease because corroded wires going to the battery or alternator from the stator or the regulator will affect the ability of the charging system to properly charge a battery.

Motorcycle voltage regulator connections must be clean and tight for proper operation so it must be verified that both the AC (stator) connections and the DC (battery supply side) connectors are clean, fully inserted and locked in place with the regulator latches (they should also be coated with dielectric grease to keep them clean and corrosion free).

The motorcycle voltage regulator is a series regulator that is also a rectifier that changes stator supplied alternating current (AC) to direct current (DC) which the battery system requires. If the charging system does not keep the battery properly charged both with regards to Voltage (between 13 VDC minimum and 15.5 VDC maximum) and the current supply at a high enough amperage to meet the system lighting, ignition, TSM/TSSM, security and accessory requirements plus a minimum of 3.5 more amps (3.5 amps more than the foregoing system requirements) there are a number of tests that can be done to ascertain why.

As the voltage regulator must have a good, clean, tight (and otherwise secure) ground connection for proper operation a Voltage Regulator Ground Circuit Test can be accomplished by connecting an ohmmeter to a known good ground (like the battery negative post) and the case of the regulator. If there is continuity with little resistance the ground is GOOD and nothing more needs to be done BUT if there is NO continuity or there is more than minimal resistance the ground will need to be fixed so there is a low resistance continuity by either locating and fixing the poor ground or adding a new grounding wire from the regulator case to a know good ground.

A Voltage Regulator Power Circuit Test can be accomplished by turning OFF the Ignition, disconnecting the voltage regulator and with an ohmmeter set to the Rx1 setting, testing for continuity between the voltage regulator wire harness supply terminal and the main fuse terminal (with the fuse removed) and if there is continuity present then the wiring circuit here is GOOD but if there is NO continuity then you will need to either find the open and repair it or replace the whole wire running from the voltage regulator to the main fuse.

As there should be no short circuit in the power supply from the regulator to battery (main fuse) wiring OR in the regulator internal circuitry continuity from these both need to be checked again with an ohmmeter set to the Rx1 setting. If the regulator to main fuse wiring connector is not disconnected from the regulator you can connect an ohmmeter with one lead on the regulator supply wire terminal end at the main fuse (with the main fuse removed) and the other lead to a known good ground. If there is NO continuity then you know that both the supply wire and the regulator are okay (as there is no short to ground). BUT if there is continuity then either the regulator or wiring or both is/are shorted to ground. To determine where there is a short circuit (i.e. either the wiring or the regulator internal circuitry) you must disconnect the DC side of the wiring harness (the connector at the DC side of the regulator) from the regulator and test between either or both ends of the wire i.e. from the regulator wire harness.

AC Output Check
Disconnect the voltage regulator connector from the alternator stator wiring and then connect an AC voltmeter across both stator sockets of a two wire stator, or if a three wire stator across two of the three for example 1 & 3 and then later you will repeat the test between 2 & 3 and later between 1 & 2. THEN run the engine at as close as possible in the circumstances to 2000 RPM. The AC output should be approximately 32-40 VAC, approximately 16-20VAC per 1000 RPM. If you have done a stator static test and the stator has proven to be in good mechanical condition and the AC output is below specifications, the charging problem is going to be a faulty rotor. If you have not done a static stator check yet and the AC output is less than as set out above it may be that the stator is defective and the static stator check will need to be done. While the regulator has nothing whatsoever to do with the alternator output, if the alternator output is good the regulator might be defective in either rectification or in limiting the output to the battery to under 15 VDC. If AC output is low and the stator has passed the static stator check then it is likely that the permanent magnets in the alternator rotor are weak. A permanent magnet can lose its magnetic strength if it is dropped or shocked such as letting it snap into place when being installed or possibly by use of an impact wrench to remove the compensator fastener etc.

May 27, 2014 | Harley Davidson FLSTF - FLSTFI Fat Boy...

1 Answer

2004 Ultra classic won't charge battery


Motorcycle voltage regulator connections must be clean and tight for proper operation so it must be verified that both the AC (stator) connections and the DC (battery supply side) connectors are clean, fully inserted and locked in place with the regulator latches (they should also be coated with dielectric grease to keep them clean and corrosion free).

The motorcycle voltage regulator is a series regulator that is also a rectifier that changes stator supplied alternating current (AC) to direct current (DC) which the battery system requires. If the charging system does not keep the battery properly charged both with regards to Voltage (between 13 VDC minimum and 15.5 VDC maximum) and the current supply at a high enough amperage to meet the system lighting, ignition, TSM/TSSM, security and accessory requirements plus a minimum of 3.5 more amps (3.5 amps more than the foregoing system requirements) there are a number of tests that can be done to ascertain why.

As the voltage regulator must have a good, clean, tight (and otherwise secure) ground connection for proper operation a Voltage Regulator Ground Circuit Test can be accomplished by connecting an ohmmeter to a known good ground (like the battery negative post) and the case of the regulator. If there is continuity with little resistance the ground is GOOD and nothing more needs to be done BUT if there is NO continuity or there is more than minimal resistance the ground will need to be fixed so there is a low resistance continuity by either locating and fixing the poor ground or adding a new grounding wire from the regulator case to a know good ground.

A Voltage Regulator Power Circuit Test can be accomplished by turning OFF the Ignition, disconnecting the voltage regulator and with an ohmmeter set to the Rx1 setting, testing for continuity between the voltage regulator wire harness supply terminal and the main fuse terminal (with the fuse removed) and if there is continuity present then the wiring circuit here is GOOD but if there is NO continuity then you will need to either find the open and repair it or replace the whole wire running from the voltage regulator to the main fuse.

As there should be no short circuit in the power supply from the regulator to battery (main fuse) wiring OR in the regulator internal circuitry continuity from these both need to be checked again with an ohmmeter set to the Rx1 setting. If the regulator to main fuse wiring connector is not disconnected from the regulator you can connect an ohmmeter with one lead on the regulator supply wire terminal end at the main fuse (with the main fuse removed) and the other lead to a known good ground. If there is NO continuity then you know that both the supply wire and the regulator are okay (as there is no short to ground). BUT if there is continuity then either the regulator or wiring or both is/are shorted to ground. To determine where there is a short circuit (i.e. either the wiring or the regulator internal circuitry) you must disconnect the DC side of the wiring harness (the connector at the DC side of the regulator) from the regulator and test between either or both ends of the wire i.e. from the regulator wire harness connector terminal and a known good ground and/or the main fuse terminal end of the wire and a known good ground. If there is any continuity the wire is shorted to ground and the short circuit must be found and repaired or the wire must be completely replaced. If there is no such continuity then the regulator DC supply terminal (with the DC side of the regulator connector disconnected) must be tested by putting one lead of an ohmmeter on the regulator terminal and the other on a known good ground. If there is continuity the regulator is shorted to ground and must be replaced. If there is a short in the wiring it is unlikely BUT the regulator could ALSO be internally shorted so it should also be checked either before or after any wiring short is located and repaired.

The voltage regulator must also properly regulate the rectified DC voltage supplied to the battery so that it is not less than 13 VDC or more than 15.5 VDC. If the regulator is not properly limiting supply voltage to the battery to 15.5 VDC or less it will be overcharging the battery. This can be tested for by operating the motorcycle engine at 3000 rpm while placing a voltmeter between the battery positive and negative posts and reading the supplied voltage. If the reading is greater than 15.5 VDC the regulator is defective and must be replaced. If the voltage is less than 15.5 VDC but more than 13 VDC the regulator and the rest of the charging system are operating correctly. If the supplied voltage is less than 13 VDC the AC side of the system must be tested and if the AC side is good but the supplied voltage at the battery is less than 13 VDC then the regulator is defective and must be replaced. If the AC side of the system is not providing correct AC supply then the stator must be tested and if it is bad, replaced and if it is good then the rotor inspected (cannot be electrically tested as it consists of permanent magnets but it could be inspected fro physical damage and roughly tested for strong magnetic force fields by using a ferrous metal object to see if the attraction of the magnets is strong or weak, but this is basically a better guess rather than a precise measurement). The rotor can also be physically inspected for physical signs of damage including signs of the center hole having become oval AND the stator bolts inspected for possibly having come loose and into contact with the rotor.


AC Output Check
Disconnect the voltage regulator connector from the alternator stator wiring and then connect an AC voltmeter across both stator sockets of a two wire stator, or if a three wire stator across two of the three for example 1 & 3 and then later you will repeat the test between 2 & 3 and later between 1 & 2. THEN run the engine at as close as possible in the circumstances to 2000 RPM. The AC output should be approximately 32-40 VAC, approximately 16-20 VAC per 1000 RPM. If you have done a stator static test and the stator has proven to be in good mechanical condition and the AC output is below specifications, the charging problem is going to be a faulty rotor. If you have not done a static stator check yet and the AC output is less than as set out above it may be that the stator is defective and the static stator check will need to be done. While the regulator has nothing whatsoever to do with the alternator output, if the alternator output is good the regulator might be defective in either rectification or in limiting the output to the battery to under 15 VDC. If AC output is low and the stator has passed the static stator check then it is likely that the permanent magnets in the alternator rotor are weak. A permanent magnet can lose its magnetic strength if it is dropped or shocked such as letting it snap into place when being installed or possibly by use of an impact wrench to remove the compensator fastener etc.

Apr 28, 2014 | 2004 Harley Davidson FLHTCUI Electra Glide...

1 Answer

2011 Honda CBF Stunner not charging


Hi, Jithin before testing any electrical component in the Charging System it is "IMPERATIVE" that you have a fully charged battery of 12.5 volts or more and be able to pass a proper "LOAD" test if necessary, you may have a preliminary reading of 12.5 volts or more but little or zero amperage, the battery is faulty and must be replaced. AGM type batteries fall into this scenario more so than lead-acid batteries.
1. Battery Test:
The battery needs to be a fully charged and load tested to ensure proper readings, connections need to be clean and tight. If you are not working with a fully charged and functional battery, all other voltage tests will be incorrect. Standing battery Voltage should be 12.5-13.2 DCV.
2. Charging System Voltage Test:
Start motorcycle, measure DC volts across the battery terminals you should have a reading of approximately 13.2-15 DC Volts.
3. Connections and wires:
Inspect the regulator stator plug, and check the battery terminals for connection corrosion. If everything seems to be in order, move on to number 4 below to determine if there's a failed component.
4. Stator Checks/Rotor Check: Each of the following tests isolates the Stator & Rotor. If AC output and resistance test fail and stator test passes then the rotor is at fault (Pull Primary covers and inspect rotor for damage).
5. AC Output Check:
Unplug the regulator plug from the stator start motorcycle and change Voltmeter to AC volts. Probe both stator wires with your meter lead. The motorcycle should be putting out approximately 18-20 ACV per 1,000 rpm. Reading will vary depending on system, check service manual specification
Generic Specs:
22 amp system produces about 19-26 VAC per 1,000 rpm
32 amp system produces about 16-20 VAC per 1,000 rpm
45 amp system produces about 19-26 VAC per 1,000 rpm
Stator Resistance Check:
Switch your multimeter to Ohm x 1 scale. Probe each stator wires with meter leads and check resistance on the meter.
Resistance should be in the range of 0.1-0.5 Ohms. Reading will vary depending on the system, check the service manual for specifications.
Generic Specs:
22 amp system produces about 0.2 to 0.4 ohms
32 amp system produces about 0.1 to 0.2 ohms
45 amp system produces about 0.1 to 0.2 ohms
5. Stator Ground Check:
Switch your multimeter to Ohm x 1 scale.
Probe each stator wire with your positive lead on the multimeter and the negative to ground.
There should be no continuity to ground on either wire.
If there is continuity your stator is shorted to ground and must be replaced.
6. Regulator Test:
Each of the following tests isolates the regulator only, so if any of these tests fail, the regulator is at fault.
Identifying Wires:
Battery Charge Lead- Wire going from the regulator to battery positive.
AC output leads- Wires coming from the Stator to the regulator.
Ground- Wire from Regulator to ground or regulator may be grounded via the physical bolting to chassis.
Regulator Ground Test: Ensure the regulator body is grounded or grounding wire is fastened tightly to a good ground (you should verify this by checking continuity from the regulator body to chassis ground).
Fwd/Reverse Bias Test/Diode Test:
This check is testing the Diode function to ensure it is regulating the AC current for the stator into DC Current.
Switch multimeter to Diode Scale.
Place your Multimeter positive lead on each AC output wire.
Place your multimeter negative lead on the battery Charge wire.
The meter should read voltage typically around .5 volts.
Next, switch your multimeter leads putting the negative lead on the AC output wires and the Positive lead on the Battery Charge Wire. The reading should be Infinite. With your meter on the same setting, place your multimeter positive lead on the regulator ground wire or to the regulator directly, and then place your meter negative lead on the AC output leads.
The meter should read voltage typically around .5 volts.
Next, switch your multimeter leads putting the negative lead on the regulator ground and the Positive lead on the AC output wires. The reading should be Infinite.
Note: Below is a table to show the readings:
Positive Lead Negative Lead Reading
AC output 1 Battery charge lead Voltage
AC output 2 Battery Charge Lead Voltage
Battery charge lead AC output 1 ?
Battery charge lead AC output 2 ?
Ground AC output 1 Voltage
Ground AC output 2 Voltage
AC output 1 Ground ?
AC output 2 Ground ?
For more information about your issue and valuable "FREE" downloads for viewing or printing that you will need please click on the blue links below. Good luck and have a wonderful day.
Honda cbf 125 battery not charging
HOW TO CHECK YOUR CHARGING SYSTEM and CHANGING the STATOR and REGULATOR...
https://haynes.com/en-gb/honda-cbf125-09-14-haynes-repair-manual
http://www.partsfish.com/page/oem-parts-for-honda
Honda CB Owners Manuals

Jan 22, 2013 | 2011 Honda CBF Stunner

1 Answer

Replaced stator only putting out 11.7 voltage to battery running


HOw old is the battery? If the battery is no good then the stator and voltage regulator will work overtime trying to charge a bad battery and eventually burn up.
First make sure you have a good fully charged battery ( 12.60 + ). Next check to be sure all of your grounds are good. Battery to chassis, and chassis to motor. The regulator grounds to the frame through its body. Be sure there is no paint or corrossion where the regulator mounts... be sure it has a good ground.
If you have a good battery and good grounds then its either the regulator or the stator. Regulator usually fails before the stator.
A service manual will give the proper test procedure for checking stator output

Oct 01, 2012 | 2006 Harley Davidson FLHR Road king

1 Answer

I have a 1992 v750 motorcycle and i cant get it to charge


It has a battery,a stator,and a regulator. The best thing i can tell you,is to download a service manual for your bike. They are as little as $5.00 on tradebit. Use it to troubleshoot your charging issue. I Will tell you this,...if the battery is a known good battery,then it is either the stator or regulator,and you will need a volt/ohm meter to do the tests required.

Sep 25, 2012 | Motorcycles

1 Answer

I have an 04 thundercat and the charging voltage at the battery is only about 12.2 vdc what voltage should i have coming out of the stator before regulator


Hi, Kenneth the following is a comprehensive charging system test that is guaranteed to the find issue with your system.
1. Battery Test: The battery needs to be a fully charged and load tested to ensure proper readings, connections need to be clean and tight. If you are not working with a fully charged and functional battery, all other voltage tests will be incorrect. Standing battery Voltage should be 12.5-13.2 DCV.
2. Charging System Voltage Test: Start motorcycle, measure DC volts across the battery terminals you should have a reading of approximately 13.2-15 DC Volts.
3. Check Connections/Wires: Inspect the regulator/stator plug, and check the battery terminals for connection/corrosion. If everything seems to be in order, move on to number 4 below to determine if there's a failed component.
4. Stator Checks/Rotor Check: Each of the following tests isolates the Stator & Rotor. If AC Output test Fails and Resistance Check, and Stator IB Test Pass then Rotor is at fault (Pull Primary covers and inspect rotor for damage).
5. AC Output Check:
Unplug the regulator plug from the stator
Start motorcycle and change Voltmeter to AC volts.
Probe both stator wires with your meter lead.
The motorcycle should be putting out approximately 18-20 ACV per 1,000 rpm. Reading will vary depending on system, check service manual specification
Generic Specs:
22 amp system produces about 19-26 VAC per 1,000 rpm
32 amp system produces about 16-20 VAC per 1,000 rpm
45 amp system produces about 19-26 VAC per 1,000 rpm
Stator Resistance Check:
Switch your multimeter to Ohm x 1 scale.
Probe each stator wires with meter leads and check resistance on the meter.
Resistance should be in the range of 0.1-0.5 Ohms. Reading will vary depending on system, check service manual for specification
Generic Specs:
22 amp system produces about 0.2 to 0.4 ohms
32 amp system produces about 0.1 to 0.2 ohms
45 amp system produces about 0.1 to 0.2 ohms
Stator IB test or Ground Check:
Switch your multimeter to Ohm x 1 scale.
Probe each stator wire with your positive lead on the multimeter and the negative to ground.
There should be no continuity to ground on either wire.
If there is continuity to ground your stator is shorted to ground.
5. Regulator Test: Each of the following tests isolates the regulator only, so if any of these tests fail, the regulator is at fault.
Identifying Wires:
Battery Charge Lead- Wire going from regulator to battery positive.
AC output leads- Wires coming from the Stator to the regulator.
Ground- Wire from Regulator to ground or regulator may be grounded via the physical bolting to chassis.
Regulator Ground Test: Ensure the regulator body is grounded or grounding wire is fastened tightly to a good ground (you should verify this by checking continuity from regulator body to chassis ground).
Fwd/Reverse Bias Test/Diode Test: This check is testing the Diode function to ensure it is regulating the AC current for the stator into DC Current.
Switch multimeter to Diode Scale.
Place your Multimeter positive lead on each AC output wire.
Place your multimeter negative lead on the battery Charge wire.
The meter should read voltage typically around .5 volts.
Next, switch your multimeter leads putting the negative lead on the AC output wires and the Positive lead on the Battery Charge Wire.
The reading should be Infinite.
With your meter on the same setting, place your multimeter positive lead on the regulator ground wire or to the regulator directly, and then place your meter negative lead on the AC output leads.
The meter should read voltage typically around .5 volts.
Next, switch your multimeter leads putting the negative lead on the regulator ground and the Positive lead on the AC output wires.
The reading should be Infinite.
Note: Below is a table to show the readings:
Positive Lead Negative Lead Reading
AC output 1 Battery charge lead Voltage
AC output 2 Battery Charge Lead Voltage
Battery charge lead AC output 1 ?
Battery charge lead AC output 2 ?
Ground AC output 1 Voltage
Ground AC output 2 Voltage
AC output 1 Ground ?
AC output 2 Ground ?
For more information about your issue and valuable "FREE" downloads that you will need please click on the blue links below. Good luck and have a wonderful day.
http://www.jetav8r.com/Vision/Stator/fault_finding_by_www.electrosport.com.pdf
HOW TO CHECK YOUR CHARGING SYSTEM and CHANGING the STATOR and REGULATOR...
http://www.thundercat.nl/index.php/download/category/2-manuals
OEM parts for Yamaha
YAMAHA YZF600R Owner Manual
YAMAHA YZF600R Owner Manual

Aug 15, 2012 | 2002 Yamaha YZF 600 R thunder cat

1 Answer

2007 Boulevard C90T - Battery seems to not be charging. After a few hours of riding, the battery starts to lose power. I have tested with a volt meter and I get about 13.8 volts when idling, so it looks...


I have a 2006 C90T and had the exact same issues. I have no great solution for you other than to tell you that in my case it turned out to by the stator. This is one of the only known reliability issues with this bike. With the regulator and stator setup on the standard C90 the stator is basically 'running' all the time due to the type of regulator/rectifier. What myself and many other have done is to replcae the regulator with Cycle Electric CE602 (made for Dynaglide Harley). This type reduces the load to the stator hopefully extending the life of the stator. The CE602 is much larger than the stock one and will have to be relocated. All my power issue went away once upgrading to a better charging system. To be sure though I would get it into a shop to have them test it right.
Regards,
GGrinds@clubsuzuki.ord

Mar 30, 2011 | 2005 Suzuki Boulevard C90

1 Answer

I have replaced the battery and it will not hold a charge.the motor sounds like it is not firing right and when it idles the led mileage indicator flashes on and off. after I let it run for a period of...


Three things. The battery, voltage regulator and stator/rotor are all dependent on one another. If the battery is bad it can pull the voltage regulator and stator both down trying to keep it charged. So you need a known good battery to start, then check the output of the regulator with a voltmeter, if that is good, then it will keep the battery charged. If not good check stator output. Somewhere therein lies the problem, as they say.
The engine will misfire and run erratic because it is not getting enough electrical power to run the electronics that control it.
Bottom line, it sounds like the voltage regulator or stator is the problem, which are both easy to check.

May 19, 2010 | 2003 Harley Davidson FXDL Dyna Low Rider

2 Answers

My battery wont charge and I just bought it


Hi and welcome to FixYA,

Two possibilities:
  • rectifier / regulator combo (most likely);
  • corroded, burned, loose connection from the stator to the regulator (likely);
  • faulty stator (least likely).
The stator would be producing relatively high AC voltage while revving the bike. The stator output AC voltage are fed to the rectifier / regulator through 3 white wires. Check calls for testiing for the presence of the AC voltage on any pairing of the white wires before and after the connector before the voltage regulator. Check on the regulator calls for checking the battery voltage when revving the bike (14.5 VDC).

Good luck and thank you for asking FixYa.

Jan 04, 2010 | 2002 Yamaha YZF Thunder ace 1000 R

Not finding what you are looking for?
1981 kawasaki Csr 1000 Logo

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top kawasaki Experts

Arnie Burke
Arnie Burke

Level 3 Expert

4525 Answers

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a kawasaki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...