Question about 2009 Honda XL700V Transalp
Posted by Anonymous on
Hi, Anonymous for this scenario you will need your service, parts fiche, and owners manual if you can't find the best tool you ever bought for your Honda, despair not, for a mere zero $0 you can download another one. For more information about your issue and valuable "FREE" downloads that you will need for viewing or printing please click on the blue links below. Good luck and have a wonderful day.
2009 Honda XL700V Transalp bank angle sensor location Google Search
Honda Transalp XL700V Manual
Honda XL700V Owner Manual
Btw, I’m available to help over the phone in case u need at https://www.6ya.com/expert/gregg_c0ec1df182c7330e
Posted on Sep 27, 2017
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
Here's a link to this great service
Posted on Jan 02, 2017
there is not as much rake and trail on a dual sport as say a cruiser type making the straight line steering less stable at higher speeds than a bike w/ more rake and trail.,but on the other hand , much less steering effort and slow speed manueverability at lower speeds on the dual sport. raise front wheel up off ground and secure bike. come around to front of bike, kneel down and grab bottom of forks and pull & push front to back looking for steering stem bearing play if any tighten steering stem & recheck not too tight -steering should flop over when just off center ,if not -too tight loosen just enough.if still play after tightening, check bearing condition. also check front wheel bearing for play, and look for leaking fork seal,finally look for uneven tread wear caused by these conditions.make sure tire is properly inflated.
Posted on Feb 16, 2009
4 or 6 cylinder engine.
It's the rear O2 sensor,the one behind the catalytic converter.
Clear the code with OBDII scanner or remove negative cable for 2 minutes.
Wait until the exhaust cool for 1 hours
Disconnect the connector and clean the contacts with CRC electrical contact cleaner the contacts.
reconnect negative battery cable
Start the car and let the motor warm up.
If the code keeps coming back then you will need to purchase a O2 sensor socket + O2 to change it out.
Please rate my answer if it's helpful to you.
Posted on Dec 12, 2009
SOURCE: Honda Odyssey 1999 wher is
The oxygen sensor for bank 1 sensor 1 is located just behind where the exhaust pipes from the front bank of cylinders and rear bank of cylinders join up. If you look under the car from the front and follow the exhaust pipes, it is the one you can see easily. There are only two oxygen sensors on the car---the one described above is bank 1 sensor 1. The other sensor goes into the side of the catalytic converter. It is bank 1 sensor 2.
Posted on Feb 08, 2011
Tips for a great answer:
Jan 27, 2018 | 2009 Honda XL700V Transalp
Mar 12, 2017 | 2009 Honda XL700V Transalp
Sep 16, 2016 | 2009 Honda XL700V Transalp
Feb 11, 2015 | 2009 Honda XL700V Transalp
Mar 25, 2014 | 2008 Honda XL 700 V Transalp
Jan 12, 2014 | 2008 Honda XL 700 V Transalp
Nov 07, 2013 | 2009 Honda XL700V Transalp
May 12, 2013 | 2008 Honda XL 700 V Transalp
Oct 09, 2012 | 2009 Honda XL700V Transalp
Jul 16, 2011 | 2009 Honda XL700V Transalp
23 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: